Dynabrade 51520 Guida rapida

Altri manuali Dynabrade Levigatrice

Dynabrade

Dynabrade 50371 Istruzioni per l'installazione

Dynabrade

Dynabrade 57220 Guida utente

Dynabrade

Dynabrade Dynafine 10800 Guida

Dynabrade

Dynabrade Dynaline 57405 Manuale utente

Dynabrade

Dynabrade Dynorbital 57600 Manuale utente

Dynabrade

Dynabrade Dynorbital 57130 Manuale utente

Dynabrade

Dynabrade 58441 Manuale utente

Dynabrade

Dynabrade 51582 Guida

Dynabrade

Dynabrade 57240 Manuale utente

Dynabrade

Dynabrade 51584 Guida

Dynabrade

Dynabrade Dynorbital Supreme 56800 Guida

Dynabrade

Dynabrade 57400 Manuale utente

Dynabrade

Dynabrade 48500 Guida

Dynabrade

Dynabrade 58040 Manuale utente

Dynabrade

Dynabrade Dynorbital EXTREME X31V Manuale utente

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Manuale utente

Dynabrade

Dynabrade 10600 Istruzioni per l'installazione

Dynabrade

Dynabrade Dynalocke 10750 Manuale utente

Dynabrade

Dynabrade 59306 Guida

Dynabrade

Dynabrade Dynorbital 57610 Manuale utente

Dynabrade

Dynabrade 56801 Manuale utente

Dynabrade

Dynabrade 59302 Istruzioni operative

Dynabrade

Dynabrade FB8 Guida

Dynabrade

Dynabrade 51602 Manuale utente

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente

Disassembly Instructions - Wet, Stone Polisher

Model: 51520

Important: Use these instructions along with tool parts page or manual.

Notice:

Shut off air supply and depress throttle lever to deplete air.

Disconnect tool from air supply hose.

Shut off water supply faucet and disconnect.

Remove all accessories (abrasive product, backup disc, and flanges) from tool.

Motor Disassembly:

1. Push against collar of 96227 Fitting and pull 95579 Water Line tubing from fitting.

2. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 95492 Screws in vise to hold tool with 51546 Valve Body pointing up.

Use a 3 mm hex key to remove 96296, 95916 Screws along with 01211 Lock

Washers. Turn counterclockwise.

Carefully remove valve body assembly, spacers, gaskets and o-rings.

Set aside and save parts.

3 mm hex key

3. Remove motor form housing.

4. Fasten 96346 Bearing Separator (2") around 01028 Cylinder.

Place assembly in 96232 Arbor Press (#2) with pinion pointing down.

Use a Ø 1/4" drive punch to push 02373 Rotor out of 02649 Bearing.

96346 Bearing Separator

5. NOTICE: In the same way, use bearing separator, arbor press and 96213 Bearing

Removal Tool, to remove 02649 Bearing from 01732 Rear Bearing Plate.

Save parts.

96213 Bearing Removal Tool

6. Fasten 02373 Rotor in vise with aluminum or bronze jaws, with pinion pointing up.

Use an adjustable hook spanner wrench to remove 51513 Pinion Gear. Turn

counterclockwise.

Remove front bearing, plate, spacer and shims.

Motor disassembly completed.

Clean and inspect parts for wear or damage. Save and reuse good parts.

Right Angle Gear Disassembly:

1. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 51545 Housing in vise with spindle pointing up.

Use a HEAT GUN to warm housing.

Use an adjustable pin spanner wrench to remove 51551 Spindle Retainer. Turn

clockwise. Left Hand Thread.

HEAT

GUN

2. Loosen vise and remove housing.

Remove 96584 O-Ring.

Remove spindle and bevel gear assembly.

Remove 98243 Wave Spring.

3. Fasten 96346 Bearing Separator (2") under 02057 Bearing.

Place assembly in 96232 Arbor Press (#2) with threaded end of spindle pointing

down.

Use a Ø 3/16" drive punch to push spindle out of 02057 Bearing.

NOTICE: In the same way, use bearing separator and arbor press to remove

51514 Gear and 02685 Bearing.

IMPORTANT: Inspect 95913 Seals and 51550 Spindle. Replace worn parts!

NOTICE: Loctite #380 is used to retain 95913 Seals in 51551 Spindle Retainer.

Acetone can be used to soften adhesive and remove seals. SEE: Right Angle

Gear Assembly.

Right angle gear disassembly completed.

Clean and inspect all parts for wear or damage. Only reuse good parts.

Notice: To disassemble and assemble muffler and valve components, refer to

parts page or tool manual and follow exploded view instructions.

96346 Bearing Separator

Assembly Instructions - Wet, Stone Polisher

Motor Assembly:

1. Install 01010 Spacer onto rotor.

Install .003" (~0.08 mm) shim thickness into 02375 Front Bearing Plate.

Install 01007 Bearing into front bearing plate.

Install bearing and plate onto rotor.