Dynacord PowerMax PM 2600 Manuale utente
POWER AMPLIFIERS 31
Originally designed for the Xa-Systems, this system power
amplifier offers various adjustment features and reveals its
true versatility when being used with any other Hi/Mid/
Sub woofer speaker system combination.
The Mid/Hi-Equalizer with integrated horn-equalization at
12 kHz can be optimally used with medium or long-throw
Mid/Hi speaker systems.
Separating the LF-range from the rest of the audio signal,
an active Butterworth/Constant-Power-Response-Cross-
over provides a crossover frequency at 160 Hz with
18 dB/oct. slope. A 12 dB/oct. Lo-Cut filter cuts ultra-low
frequencies below 30 Hz.
Xa2600/PM2600
DualActive2-Way
ProcessedPrecisionPowerAmplifier
2600Watts
The heart of any Xa-system, PowerMax system or of a
freely configured 2-way system is one of our 2600 Series
Controller Amps.
Based on the topology of the “LINEAR PRECISION” Series
power amps, these system power amplifiers offer an out-
put power capacity of 2,600 watts (RMS) each, when
operated in active 2-way mode. Both models provide in-
tegrated active frequency crossovers, several processor-
controlled functions and extensive protection circuitry.
The provided output power is:
2 x 700 watts Lo
2 x 600 watts Hi
The multitude of processor functions includes our patented
LPN-filters, the ”Thermal Brain Circuit" protection, and an
APC-controlled limiter for each amplifier channel.
Additional protection circuitry prevents thermal overload,
HF, DC or short-circuit in the output stage. The Linear
Precision Series' Back-EMF-protection circuitry contributes
to the overall operational stability.
The integrated bass equalizer is meant to be used for live
concerts. The 4 kHz Dip-switched EQ allows the adjust-
ment of several different cabinets to match varying acous-
tical environments. A 12 dB/oct. Lo-Cut filter attenuates
ultra-low frequencies.
•LPN Processor Function
The patented LPN-Processors (Low Pass Notch Filter)
electronically neutralize speaker-typical transient response
distortion already within the power amp.
•APC Processor Function
Four super-high-speed audio processors continuously
monitor the amplifier's internal and external operational
state, activating the four internal dynamic limiters on the
occurrence of any non-linear operation.
•TBC Processor Function
Four Thermal-Brain circuits simulate the thermal model of
a typical voice coil and limit the energy fed to the speaker
components during impending overload.
32 POWER AMPLIFIERS
PM2600
Crossover Section Xa2600 PM2600
Crossover Type 3rd Order BU, Constant-Power-Response PowerMax12*, Stereo active 2-way
Stereo active 2-way
Crossover Frequency 160 Hz 110 Hz
Lo-Cut 12dB/octave, 30Hz at -3dB ref. 1kHz 12dB/octave, 25Hz at -3dB ref. 1kHz
*Patent pending
Xa2600, PM2600
HI-Channels LO-Channels
Load Impedance 8Ω4Ω8Ω4Ω
Maximum Midband Output Power, THD = 1%, 1kHz, 60Hz 380W 700W 380W 700W
Rated Output Power, THD < 0.1% 300W 600W 350W 700W
Maximum Single Channel Output Power, 400W 750W 400W 750W
Dynamic-Headroom, IHF-A
Maximum RMS Voltage Swing, THD = 1% 58.7V
Frequency Response, -3dB, ref. 1kHz, Lo-Cut 25Hz ... 45kHz
Minimum Load Impedance 2.5 Ω
Input Sensitivity at rated output power @ 4Ω0dBu (775mV)
Maximum Input Level +21dBu (8.7V)
THD at rated output power, MBW =80kHz < 0.05%
Crosstalk Attenuation > 60dB
Slew Rate 30V/µs
Power Bandwith, THD = 1%, ref. 1kHz, half power @ 4Ω10Hz ... 50kHz
Input Impedance, 20Hz ... 20kHz, balanced 20kΩ
Damping Factor > 300
Signal-to-Noise Ratio, A-weighted > 100dB
Power Requirements 230V, 50Hz ... 60Hz
Power Consumption at 1/8 maximum output power @ 4Ω1800W
Protection Audio limiter (APC), TBC, High temperature,
DC, HF, Back-EMF, Peak current limiter,
Inrush current limiter, Turn-on delay
Cooling Front-to-rear, 4-stage-fans
Safety Class I
Dimensions (W x H x D), mm 483 x 177 x 426
Weight 30kg
Amplifier at rated conditions, all channels driven, 8Ωloads, HI-Channel rated at 1kHz, LO-Channel rated at 60Hz unless otherwise
specified. Note: 0dBu = 0.775V
Basically, the PM2600 can drive any active 2-way system
that consists of full-range cabinets and sub woofers. The
integrated frequency crossover operates in PowerMax
function mode and has been optimised for those com-
binations. Intelligently configuring system components
leads to outstanding results. For more details, please refer
to the PowerMax Systems and PowerMax230 Controller
descriptions.
PM2600
DualActive2-Way
”PowerMax“ControlledAmplifier
2600Watts
Altri manuali per PowerMax PM 2600
3
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Dynacord Amplificatore
Dynacord
Dynacord L300 Manuale utente
Dynacord
Dynacord Power Amplifier DPA 4245 Manuale utente
Dynacord
Dynacord Xa 4000 Manuale utente
Dynacord
Dynacord Power Amplifier DPA 4120 Manuale utente
Dynacord
Dynacord PCA 2250 Manuale utente
Dynacord
Dynacord PROMATRIX 8000 Series Manuale utente
Dynacord
Dynacord FX12 Guida rapida
Dynacord
Dynacord PAA 990 - SERVICE Manuale utente
Dynacord
Dynacord Promatrix 6000 PMX-2P500 Manuale utente
Dynacord
Dynacord SL 1200 - Manuale utente
Dynacord
Dynacord LX 1600 Manuale utente
Dynacord
Dynacord H 2500 Manuale utente
Dynacord
Dynacord Power Amplifier DPA 4245 Manuale utente
Dynacord
Dynacord Professional Power Amplifiers Manuale utente
Dynacord
Dynacord PCA 2450 Manuale utente
Dynacord
Dynacord SR20TGX-EU Manuale utente
Dynacord
Dynacord PSX 850 Manuale utente
Dynacord
Dynacord PROMATRIX 8000 Series Manuale utente
Dynacord
Dynacord S 900 Manuale utente
Dynacord
Dynacord DSA 8405 Manuale utente
