Dynamix HP Dynamix HP-51M Manuale utente

Dynamix HP-51M User Manual EN-V1.00

Dynamix HP

Dynamix HP-

-51M

51M

HomePNA3.1 Coax MDU Master Bridge

User’s Guide

Version 1.0

Jul. 2008

STATEMENT

TATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to correct the interference by one or more

of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help

VCCI & CE...

CAUTION: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate

the equipment.

Dynamix HP-51M User Manual EN-V1.00

TA B L E O F

A B L E O F C

CO N T E N T S

O N T E N T S

INTRODUCTION

INTRODUCTION __________________________________________________________ 1!

Features _________________________________________________________________________ 1!

Glossary _________________________________________________________________________ 1!

INSTALLATION

INSTALLATION ___________________________________________________________ 2!

Packing List ______________________________________________________________________ 2!

Rear Panel _______________________________________________________________________ 2!

Connectors_______________________________________________________________________________ 2!

LED Indicators ___________________________________________________________________________ 2!

Connecting the Cables______________________________________________________________ 3!

Verification_______________________________________________________________________ 4!

CONFIGURATION

CONFIGURATION_________________________________________________________ 5!

Configuration Methods _____________________________________________________________ 5!

Use Web Browser__________________________________________________________________ 5!

System Setup (TCP/IP Properties) ____________________________________________________________ 6!

System Assets (Information) _________________________________________________________________ 6!

EP (User) Management _____________________________________________________________________ 6!

Firmware/Driver Files ___________________________________________________________________ 7!

EP ___________________________________________________________________________________ 7!

Smart EP ___________________________________________________________________________ 8!

Properties Profile – Stored the Settings ___________________________________________________ 9!

Master HomePNA Properties (HPNA) ____________________________________________________ 9!

Security Mode _______________________________________________________________________ 9!

Privacy Mode ________________________________________________________________________ 9!

Privacy Mode Usage Example _________________________________________________________ 10!

Privacy Mode/Key Summary __________________________________________________________ 12!

Profile Status for Master and EP ________________________________________________________ 12!

EP HomePNA Properties (HPNA) _______________________________________________________ 13!

Note _______________________________________________________________________________ 13!

Host Limit _________________________________________________________________________ 13!

Upstream Rate ______________________________________________________________________ 13!

Master/Smart EP Ethernet Properties (Ether) _____________________________________________ 13!

Port Setup__________________________________________________________________________ 13!

Service and Speed/Duplex ____________________________________________________________ 14!

Bandwidth Control __________________________________________________________________ 14!

QoS Setup__________________________________________________________________________ 15!

IGMP v2 Snooping Setup _____________________________________________________________ 15!

Tag VLAN Setup ____________________________________________________________________ 15!

Status and Statistics _________________________________________________________________17!

Reset to Default _____________________________________________________________________ 17!

Delete the Obsolete EP Profile__________________________________________________________ 17!

Diagnosis ____________________________________________________________________________ 17!

Device Noise in Master and EP ________________________________________________________ 18!

Physical Connection between Master and EP ____________________________________________ 18!

Administration___________________________________________________________________________ 19!

Administrator _________________________________________________________________________ 20!

Allowed Source _______________________________________________________________________ 20!

Telnet/Http/Snmp Setup _______________________________________________________________ 21!

System Log _____________________________________________________________________________ 22!

System Time ____________________________________________________________________________ 22!

Static MAC _____________________________________________________________________________ 23!

Reboot System___________________________________________________________________________ 23!

Default Setting___________________________________________________________________________ 23!

Upload Firmware_________________________________________________________________________ 23!

Activate Firmware________________________________________________________________________ 24!

Backup/Restore Configuration ______________________________________________________________ 24!

Example to Upload then Activate System Firmware and HCNA Driver ______________________________ 24!

Current System Firmware and HCNA Driver Version_______________________________________ 24!

New System Firmware and HCNA Driver Files ____________________________________________ 25!

System Firmware _____________________________________________________________________ 25!

Upload the New System Firmware _____________________________________________________ 25!

Check the New System Firmware in ‘Upload Area’ _______________________________________ 27!

Activate the New System Firmware ____________________________________________________ 28!

HCNA Driver _________________________________________________________________________ 29!

Upload the New Master/EP HCNA Driver _______________________________________________ 29!

Upgrade the New HCNA Driver _______________________________________________________ 30!

Master/EP runs the New HCNA Driver _________________________________________________ 32!

System Firmware and HCNA Driver Version after Upgrade _________________________________32!

Use Telnet _______________________________________________________________________ 34!

Command Sets for Telnet Console ___________________________________________________________ 35!

dconfig ______________________________________________________________________________ 35!

default_______________________________________________________________________________ 35!

diag _________________________________________________________________________________ 35!

dir __________________________________________________________________________________ 36!

dns _________________________________________________________________________________ 36!

exit__________________________________________________________________________________ 36!

quit _________________________________________________________________________________ 36!

ep __________________________________________________________________________________ 36!

ephpnareboot ________________________________________________________________________ 36!

epstat _______________________________________________________________________________ 36!

epswc _______________________________________________________________________________ 36!

epswigmp____________________________________________________________________________ 36!

epswqosq____________________________________________________________________________ 36!

epswqosrate _________________________________________________________________________ 36!

epswqostc ___________________________________________________________________________ 36!

epswtagvlan__________________________________________________________________________ 36!

filter _________________________________________________________________________________ 36!

help _________________________________________________________________________________ 36!

hpnareboot___________________________________________________________________________ 37!

ipconfig ______________________________________________________________________________ 37!

logserver ____________________________________________________________________________ 37!

master_______________________________________________________________________________ 37!

passwd ______________________________________________________________________________ 37!

ping _________________________________________________________________________________ 37!

reboot _______________________________________________________________________________ 37!

rmep ________________________________________________________________________________ 37!

service ______________________________________________________________________________ 37!

showep ______________________________________________________________________________ 37!

showlog _____________________________________________________________________________ 37!

showmaster __________________________________________________________________________ 37!

snmp ________________________________________________________________________________ 37!

snmptrapserver _______________________________________________________________________ 38!

snmptrapsetup _______________________________________________________________________ 38!

sntp _________________________________________________________________________________ 38!

stat _________________________________________________________________________________ 38!

swconfig _____________________________________________________________________________ 38!

swigmp ______________________________________________________________________________ 38!

swqos _______________________________________________________________________________ 38!

Dynamix HP-51M User Manual EN-V1.00

swqosrate____________________________________________________________________________ 38!

swqostc _____________________________________________________________________________ 38!

swsmac _____________________________________________________________________________ 38!

swtagvlan ____________________________________________________________________________ 39!

tftp __________________________________________________________________________________ 39!

time _________________________________________________________________________________ 39!

upep ________________________________________________________________________________ 39!

upmaster ____________________________________________________________________________ 39!

upsys _______________________________________________________________________________ 39!

useradd _____________________________________________________________________________ 39!

userdel ______________________________________________________________________________ 39!

users ________________________________________________________________________________ 39!

Use SNMP_______________________________________________________________________ 40!

ADVANCED FEATURES

ADVANCED FEATURES __________________________________________________ 41!

QoS ____________________________________________________________________________ 41!

Priority in Upstream and Downstream ________________________________________________________ 41!

802.1p _________________________________________________________________________________ 41!

IP TOS_________________________________________________________________________________ 41!

TCP/UDP Port Number____________________________________________________________________ 41!

SPECIFICATIONS

SPECIFICATIONS ________________________________________________________ 42!

DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide

INTROD UCTION

NTROD UCTION

This chapter describes the features of your HomePNA3.1 over Coax to Ethernet Master (Management) Bridge --

HP-51M. Refer to “HomePNA3.1 over Coax” as HCNA from this point.

Features

♦One HCNA Port for Driving HomePNA3.1 Signal into Existing Coaxial Cable

♦One TV/Antenna Port for TV Set Connection or for TV Signal from VHF/UHF Antenna/CATV

♦Two Fast Ethernet Port with Auto-Detect MDIX Function(Auto Crossover) and Auto-Negotiating Half/Full

Duplex 10M/100M for Expansion or Link to FTTx/xDSL Modem

♦One Reset Button

♦Priority Queue based QoS Support for 802.1p, IP TOS, UDP/TCP Protocols

♦Supports up to 31 EP (Endpoint, as HP-51S Slave Unit) Concurrent Connections

♦Built-in Diagnostic Function for Individual EP Connection

♦Built-in Web Server and Telnet Server to Support Remote Configuration via Web Browser or Telnet Protocol

♦Supports Remote HTTP/TFTP Upgrade Function for System Firmware and HCNA Driver

♦Supports HCNA Driver Upgrade On-line for Connected EPs

♦Supports SNMP Function

Glossary

♦HCNA HomePNA3.1 over coaxial cable

♦MDU Multiple Dwelling Unit

♦Coax Coaxial cable

♦SyncMode HCNA device operates in Synchronous mode

♦AsyncMode HCNA device operates in Asynchronous mode

♦Master Master HCNA device in one coax network

♦Slave Slave HCNA device in one coax network

♦EP Endpoint, equivalent to Slave HCNA device, as HP-51S

♦Smart EP Smart Endpoint, as HP-51S. HP-51M could configure Smart EP’s Ethernet properties.

♦QoS Quality of Service

♦M/C Fiber-Optic Ethernet Media Converter

♦Mixer Coax device sums two or more signals into one

♦Splitter Coax device divides a signal into two or more smaller and approximately equal signals.

♦Combiner Coax device adds several discrete signal inputs to one and has high isolation between inputs

♦Duplexer Coax device separates 2 signals within the same band

♦Diplexer Coax device separates 2 signals in different bands

♦Tap Coax device uses for matching impedance or connecting subscriber drops

♦dB Decibel, to express either a gain or loss power ration(log) after the signal has been transmitted

DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide

INSTALLATION

NSTALLATION

This chapter describes the installation procedure for your bridge.

Packing List

Your package should come with the equipment listed below,

♦One Main Unit (HCNA to Ethernet Master Bridge) HP-51M

♦One DC 5V Power Adaptor

♦One F-Type Coaxial Cable (RG-59U)

♦One RJ-45 Ethernet Cable (CAT-5)

Rear Panel

Figure 1: Rear Panel of HP-51M

Connectors

1. DC5V: Connect to the power adapter plug.

2. LAN1/LAN2: Two fast Ethernet ports to connect Switch/FTTx/xDSL Modem for Internet access.

3. Reset: While HP-51M is turned on, press and release this button will reboot HP-51M. Press it for lasting 5

seconds will restore all settings to factory default. For example, the IP address will restore to default

‘192.168.1.1’.

4. HCNA: Attach to existing coaxial cable and use it as the networking backbone in one or more MDUs. HP-51M

is the HCNA Master device and controls the other Slave HCNA devices (refer to Endpoint or EP, as HP-51S)

on the same coax network. Refer “Connecting the Cables” for more details.

5. TV/Antenna: Connect to TV Set. Or connect to VHF/UHF antenna or CATV to bypass TV signal to HCNA

port.

LED Indicators

1. Power: Lighting up when power on.

2. LAN1: Lighting up when LAN1 port is active, and flashing when there is any data traffic.

3. LAN2: Lighting up when LAN2 port is active, and flashing when there is any data traffic.

4. Link/Act: Lighting up when HCNA port is active, and flashing when there is any data traffic.

5. SyncMode: Lighting up when HCNA port is working in HCNA Synchronous MAC mode.

6. Diagnosis: Lighting up when HP-51M is diagnosing EP.

NOTE: HCNA always adopt the Synchronous MAC protocol layer in coax system in order to coordinate all the

transmissions and eliminate any collisions. The SyncMode led should be always on after power on.

DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide

Connecting the Cables

To establish a new coax networking system by HP-51M, reroute the CATV/Antenna signal source over coax toward

HP-51M ‘TV/Antenna’ port and connect HP-51M ‘HCNA’ port to the original coax entrance to building. HP-51M

works as a Combiner for TV and HCNA signal. In each Dwelling Unit, use the HCNA EP to extract the TV signal

and Ethernet packets. See Figure 2 for the detail cabling in one MDU,

Figure 2: Detail cabling of HP-51M

HP-51S

Splitter

Tap

Optical

Fiber

VHF/UH

Satellite/CAT

HP-51M

DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide

You can also use other Combiner or Mixer-Splitter with HP-51M to build the same system, see the following Figure

3for different cabling,

Figure 3: Different Cabling of HP-51M

NOTE: After power up HP-51M, the led ‘SynMode’ will always be glowing, and led ‘Link/Act’ will light up for at

least one EP is detected on the HCNA network. A dimmed led ‘Link/Act’ shows no EP attached to the HCNA

network.

NOTE: The minimum attenuation between Master and EP is 12dB. EP is usually connected to the coaxial cable via

a Tap device that provides enough attenuation (contributes more than 20dB). If you intend to connect the Master

and EP directly for test purpose, please add the attenuator that exceeds 12dB to the coaxial cable.

Verification

After you have finished the installation, you should be able to access HP-51M through Ethernet link or through

HCNA link (via Host PC behind EP) to verify the installation is completed. (See next Chapter for details).

HP-51M

Splitter

M/C

Optical Fiber

ISP

VHF/UHF

Satellite/CATV

Combiner

Mixer

Indice

Altri manuali Dynamix Hardware di rete

Dynamix

Dynamix DC-16S Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente