E Star Fokker Eindecker Manuale utente

INSTRUCTIONS

www.estarmodels.com

KIT INCLUDES

ITEMS NEEDED TO COMPLETE

Full size plan.

Lasercut parts.

3.0mm W100xL600mm plywood : 3sheets

2.0mm W100xL300mm plywood : 1sheet

5.0mm W100xL565mm balsa : 1sheet

5.0mm W100xL365mm balsa : 1sheet

3.0mm W100xL600mm balsa : 1sheet

3.0mm W100xL590mm balsa : 2sheets

3.0mm W100xL465mm balsa : 1sheet

3.0mm W100xL340mm balsa : 2sheets

3.0mm W100xL330mm balsa : 1sheet

1.5mm W100xL525mm balsa : 2sheets

1.5mm W100xL465mm balsa : 2sheets

1.5mm W100xL405mm balsa : 2sheets

1.5mm W100xL230mm balsa : 1sheet

Landing gear (2.0mm Music wire 414, 395, 350mm)

Tail hardware (1.5mm Music wire 220, 72mm, PVC sleeve)

Aileron Pushrods (2ea)

CA hinge

Rubber rings for tire(2ea)

Clear Plastic

Instructions and Stickers.

Download full color instructions from

http://www.estarmodels.com [Download] menu.

CAUTION

Be sure to use suitable power.

Too much power makes this plane unstable.

Brushless Motor (Max 20A/220W)

Brushless ESC 30A

Slow Propeller 1047~1147

Receiver (4ch Min.)

4 submicro Servos

Li-Poly 3s(11.1V) 1800mAh Battery

One and half rolls of covering film.

Thick nylon thread, rubber bands

EZ connectors (2ea) and Wheel Collars (4ea)

Page 1

PREPARATION



Remove parts from laser-cut panel and group as shown

above.

VERTICAL TAIL

1. Lay waxed paper or PE film over the plan.

Pin the vertical tail parts(R1-R5) on the plan and glue

together with thick CA.

2. Remove vertical tail from the plan and glue the parts(R6-

R7). Apply thick CA glue at each joints for reinforcing.

3. Carefully sand surfaces.

HORIZONTAL TAIL

1. Lay waxed paper or PE film over the plan.

Pin the horizontal tail parts(E1-E8) on the plan and glue

together with thick CA.

Use scrap balsa as a supports for the edge parts.

2. Remove horizontal tail from the plan and glue the

capstrips(E9). Cut PVC sleeve(L=75mm) and insert to the

hole of ribs and glue it.

3. glue the leading and trailing edge (E10-E11).

Apply thick CA glue at each joints for reinforcing and then

carefully sand surfaces.

Page 2

RIGHT WING

1. Glue rear spars (W10) together with thick CA.

2. Lay waxed paper or PE film over the plan.

Pin fore lower spar(W9), rear lower spar(W10), trailing

edge(W12) on the plan. Use scrap balsa as a supports for

the spars.

Assemble wing ribs(W1-W5).

3. Assemble fore riblets(W7-W8), upper spars(W9-W10),

wingtip(W13) and wingtip rib(W6).

Glue together with thick CA.

4. Glue wingroot upper panels(W19-W21), small

sheets(W22), servo trays(W23), gusset(W26) and wingtip

support(W13A).

5. Glue wingroot lower panels (W16-W18), small

sheets(W22), servo bay(W24), leading edge(W14) and

wingtip trailing edge(W15).

Apply thick CA glue at each joints for reinforcing.

LEFT WING

1. Assemble left wing as same way of right wing.

2. Carefully sand surfaces.

AILERONS

1. Lay waxed paper or PE film over the plan.

Pin trailing edge(A4)and small sheets(A6) on the plan and

assemble aileron ribs(A2-A3), tip(A5), sub leading

edge(A1), gusset(A9) and leading edge(A7).

2. Apply thick CA glue at each joints for reinforcing and

then carefully sand surfaces.

3. Assemble left aileron as same way of right aileron.

Page 3

FUSELAGE

1. Lay waxed paper or PE film over the plan.

Pin the fuselage fore right side panel(F4), doublers(F5,F6A)

and longerons(F1-F3) on the plan and glue together with

thick CA.

2. Pin the fuselage rear right side panel(F20-F21,F22,

F24,F26,F28,F30) on the plan and glue together with thick

CA.

3. Assemble bulkheads(F6-F9) and longerons(F2),

doublers(F5,F6A), battery tray(F8A) and servo tray(F10).

Glue together with thick CA.

Attention Check your battery size before assemble

bulkheads(F6-F8). If necessary, enlage battery space.

4. Assemble fore right side panel(F4) and glue.

5. Pin the parts for fuselage rear left side panel(F1-F2,F20-

F21,F22, F24,F26,F28,F30) on the plan and glue together

with thick CA.

6. Glue fore and rear left side panel.

7. Glue horizontal spacers(F23,F25,F27,F29,F31,F31A)

with thick CA.

8. Glue rear fuselage upper panel(F32).

9. Assemble and glue stringers(F14-F15), instrument

panel(F11), servo mounts(F12) and cockpit fairing(F13).

10. Glue fore fuselage upper panel(F16).

11. Glue fore fuselage lower panel(F17-F19) and rear

fuselage lower panel(F33).

Page 4

12. Assemble and glue motor mount(F34,F34A,F35).

13. Assemble and glue fire wall(F36), cowling stiffners(F38)

and cowling ring(F37).

14. Glue cowl fairing(F39).

15. Glue fore cowl parts(F40-F42).

16. Assemble and glue rear cowl parts(F40-F42) as shown

above.

17. Temporary insert wing joners(F48-F49) and left wing.

18. Assemble and glue parts(F40-F42) as shown above.

Caution Do not glue it in this step. If necessary, glue it

temporarily.

19. Assemble left side.

20. Carv and sand surfaces.

Page 5

21. Glue cowl in place.

22. Glue cockpit coarming(F52).

23. Carefully sand fuselage surfaces.

24.Thread fuselage diagonal wire bracing.

WHEELS and DUMMY ENGINE

1. Glue wheels as shown(L11-L12)

Impregnate wheels with thin CA glue for reinforcing.

2. Assemble and glue crank case of dummy engine(M1-M3,

M9).

3. Roll up PVC film to the parts(M6) for dummy engine

cylinders.

(Refer to dummy engine cylinder template on the drawing.)

4. Glue dummy engine cylinders to crank case.



Page 6

PAINTING and COVERING

1. Paint cockpit coarming, cockpit inside, cowl inside,

wheels, upper cabane strut, undercarriage struts, skid

mounting struts, machine gun and dummy engine.

Impregnate struts with thin CA glue for reinforcing.

2. Cover film as shown above.

FINAL ASSEMBLY

1. Glue skid mounting strut(L5-L8) and tail skid(L9).

2. Cut CA hinges as shown above.



3. Make hinge slots and install hinges.

4. Glue plywood horns right & left(R8).

5. Insert and glue PVC sleeve to the fuselage(L=65mm).

Insert and glue elevator joiners(1.5mm piano wire,

L=220mm, L=72mm).

Glue plywood horns right & left, upper & lower(E12).

6. Connect control wires to the rudder and elevator horns.

Page 7

7. Install rudder and elevator servos.

8. Glue the parts(W25), make aileron hinge slots and then

install hinges.

9. Glue the parts(W25), plywood horn(A8) and install

aileron pushrod.

10. Install motor.

11. Glue dummy engine to the motor mount with M9 parts.

12. Glue undercarriage fore(L1), rear(L2), center strut(L3).

Install main landing gear, main gear axle, gear strut and tie

with thread and then apply with thin CA glue.

Tie main landing gear and fore strut with elastic cord to

function as a shock absorber.

13. Glue rubber rings to the wheel with thin CA.

Install wheel and collars.

14. Glue plywood landing gear(L4) and tie with thread.

Page 8

15. Insert and glue wing joiner(F48-F49).

It must be same length with left and right.

16. Insert wing to the wing joiner.

17. Glue upper cabane strut(F51) and tie upper front spar

bracing wires(A), rear spar bracing wires(B) and strut fore

bracing wires(C).

18. Tie lower front spar bracing wires(D), rear spar bracing

wires(E) and undercarriage strut bracing wires(F).

Sight the trailing edge of both wings and check for warps.

Adjust tention of bracing wires to straighten wings

19. Glue windshield, step(L10) and machine gun(F50).

(Refer to windshield template on the drawing.)

PRE-FLIGHT CHECK

CG.

Check CG. (CG location is shown on the drawing.)

Control Throws.

The following control throws are recommended starting

points. After you are familiar with this plane, you may

increase, or decrease.

- Ailerons : 16mm(5/8”) up down.

- Elevator : 10mm(3/8”) up and down.

- Rudder : 19mm(3/4”) right and left.

Page 9

Indice

Altri manuali E Star Giocattolo

E Star

E Star Bleriot XI La Manche Manuale utente

E Star

E Star AIR TRACTOR AT-802 Manuale utente

E Star

E Star OV-10 BRONCO Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente