Eachine E011C Manuale utente
AGE 14+
E011C
DRONE X BRICK 2 IN 1
*Please read this manual carefully before operation
and keep it properly for future reference.
1
4
3
2
1
7
6
5
1
23
4
5
6
7
KNOW YOUR
E011C
Block-man
Protective Guard
Propeller
Motor Holder
Battery
Casing
Motor
E011C Drone applies building blocks into the drone
construction and uses 2.4GHz to enable multiple
players compete without any risk of interference. It is
easy to operate via remote control to control functions
such as flying, 3D flips and rolls, return to home,
headless mode and other features.
2
AGE 14+
E011C
DRONE X BRICK 2 IN 1
*Please read this manual carefully before operation
and keep it properly for future reference.
ACCESSORIES
E011C
x1
(Battery Included) Remote Control x1
Backup Propeller x4 USB Charging Cable x1
User Manual x1
Notes:
Please check the number of accessories carefully
(as shown above). Please provide proof of purchase
and contact the store for replacement if any missing
parts.
Flat Screwdriver x1
3
PRE-FLIGHT PREPARATION
1.Flight Environment
Please keep the drone in sight during the flight and
keep it away from barriers, high-tension cables,
trees and people.
Do not fly in extreme environment, such as hotness,
coldness, strong wind or heavy rain.
Indoor: Spacious spaces away from barriers, crowds
or pets are preferred.
Outdoor: Sunny, windless and breezy weathers are
preferred.
4
A
AB
B
A corresponds to A
B corresponds to B
①Fix Block-man onto
the drone.
②Block-man stands
still above the drone.
Hold onto the hat of the
blades, align the hat to
the motor shaft and
press until fixed.
FRONT
3.Block-man Installation
Notes:
When installing or dismantling the propeller, please
do not exert force on the propeller to avoid distortion.
2.Propellers Installation
5
4.Battery Charging for Drone
Notes:
LED lights on when charging, LED lights off when finish
charging. Charging time is about 30-50 minutes.
A.Remove the battery from drone bottom.
B.Connect USB charging cable with lithium
battery and the USB charging interface to
charge up.
Battery lnstructions
!
There is a certain risk when using lithium battery.
It may cause fire, body injury or property loss.
Users must be aware of the risks and take full
responsibility of using battery improperly.
If battery leakage occurs, please avoid contacting
your eyes or skin with electrolyte. Once it
happens, please wash your eyes with clean water
and seek medical care immediately.
Please remove the plug immediately if you sense
any peculiar smell, noise or smog.
Battery Charging
Please use the charger from original factory to
ensure your safe usage.
Do not charge dilatant or outworn battery.
Do not over charge battery. Please unplug the
charger once fully charged.
Do not charge the battery next to inflammables,
such as carpet, timber floor or wood furniture or
on the surface of electro-conductive objects.
Please always keep an eye on the battery when
charging.
Do not charge battery which not cool down yet.
The charging temperature should be between
0℃to 40℃.
Battery Recycling
Do not dispose the battery as daily rubbish. Please
familiarize yourself with the local garbage disposal
method and dispose it according to the
special requirement.
6
7
KNOW YOUR REMOTE CONTROL
Operation Board of Remote Control
Throttle Joystick/
Press for Return to
Home/Push the Rubber
Joystick to Enter Headless
Mode During Return
Forward/Backward
Fine-Tuning
Power Switch
Left/Right Turn
Fine-tuning
Indicator Light
Rubber Joystick/Short
Press for Flips&Rolls/
Long Press for Three
Seconds to Enter
Flight Mode
(Brick Block Mode/
Power Save Mode)
Notes:
Brick Block Mode is set as the default mode during flights.
However, it consumes a large amount of power to flip
and roll, resulting in shorter flight time. Therefore, it is
suggestive to disassemble the block-man and press the
mode button for three seconds to switch to another mode
for longer flight time.
1
12
34
5
6
4
5
6
2
3
8
+
-
1.5V“AAA”
+
-
1.5V“AAA”
+
-
1.5V“AAA”
+
-
1.5V“AAA”
+
-
1.5V“AAA”
+
-
1.5V“AAA”
1.Battery Assembling for Remote Control
①Open the Remote Control Battery Cover
Open the battery cover by sliding the cover downward
(as shown in figure).
②Battery Assembling for Remote Control
AAA batteries *3
Open the cover of battery compartment, insert three
AAA batteries (not included).
9
1
2
2.Pairing Remote Control with Drone
①Turn on the power of the drone; put the drone on
plain ground; check whether the indicator lights
of remote control and LED lights of drone flash.
②Push the accelerator joystick to the top and then
pull back to the bottom. On hearing a clear sound,
the indicator light of remote control and LED lights
of drone will turn from flashing lights to constant
lights, which means the pairing completes.
3.Calibration
①Calibration ②Reset the course
Calibrate the drone when it cannot vertically ascend.
Press “Calibration” button and the indicator light of
drone would start flashing,then trun to constant light.
Thus the calibration completes. Ensure the whole
process of calibration is operated under horizontal
and steady circumstances.
Indice
Altri manuali Eachine Drone
Eachine
Eachine FB90 Manuale utente
Eachine
Eachine Novice-III Manuale utente
Eachine
Eachine X140HV Manuale utente
Eachine
Eachine TYRO129 Manuale utente
Eachine
Eachine RACER 180 Manuale utente
Eachine
Eachine Racer 250 Manuale utente
Eachine
Eachine UZ65 Manuale utente
Eachine
Eachine TYRO79 Manuale utente
Eachine
Eachine E58 Manuale utente
Eachine
Eachine US65 Manuale utente
Eachine
Eachine QX105 BAT Manuale utente
Eachine
Eachine Wizard TS130 Manuale utente
Eachine
Eachine EX5 Manuale utente
Eachine
Eachine Wizard X220HV Istruzioni operative e di manutenzione
Eachine
Eachine 1S Cinefun 75mm 1080P/ 4K Cinewhoop Manuale utente
Eachine
Eachine EX3 Manuale utente
Eachine
Eachine E013 Manuale utente
Eachine
Eachine V-tail 210 Manuale utente
Eachine
Eachine Wizard X220s Manuale utente
Eachine
Eachine TYRO99 Manuale utente
