Eagle G600AF Manuale utente
G600AF, G600AG, G600AH, G600AJ, G600AK, G600AL
G600BA, G600BB, G600BC, G600BD, G600BE, G600BF
45M / 90M LED Rope Light
Installation Information and Guidance
IMPORTANT
Installers Please Note:
This Imformation should be read carefully before installation.
CONTENTS
Mains Lead Mains Connector In-Line Coupler End Cap Heat shrink
45m Kit
1 x 45m Roll of LED Rope Light
5 x End Caps
5 x Inline Couplers
5 x Mains Leads
5 x Mains Connector
5 x Strips of Heat shrink and glue
90m Kit
1 x 90m Roll of LED Rope Light
10 x End Caps
10 x Inline Couplers
10 x Mains Leads
10 x Mains Connector
10 x Strips of Heat shrink and glue
Important Information
This item and it’s components are designed for use by a professional/competent
person to produce a bespoke design/effect. It is not a finished product, and as such, it
is the responsibility of the installer to make sure that the finished product/installation
is suitable for the purposes it is being used for and is installed to meet all current
legislation and standards. The installer should pass onto the user a comprehensive
working document on how to safely use and maintain the product in the form of a
professionally written manual. A qualified electrician should test the finished item
before commissioning and handing over to the user.
Operation and Installation Guide
1) The rope light can be cut every 1m at the point marked on the rope light by
a pair of scissors or broken line.
2) The cut must be made by a sharp knife and at right angles to the rope.
Incorrect cutting of the product can cause the final join to suffer from poor
electrical connection which can lead to product failure.
3) The product can be reconnected in various ways by using the connectors
provided.
1. In-Line Coupler
2. Mains Connector
3. End Cap
4) All connections MUST be sealed with the heat shrink provided to make a
permanent join. Failure to use the heat shrink may result in the ingress of
water and/or the breaking of electrical connection leading to the possibility
of electrical shock/product damage.
5) The rope is suitable for use outside but if any connections are to be
mounted outside or are to be exposed to any form of weathering then these
connections must be additionally weather proofed. The accessories supplied
do NOT offer any form of IP rated protection.
6) The rope light should not be switched on while on the roll, in a tight coil or
in very close proximity to other LED ropes. This can lead to overheating and
damage to the product.
7) The maximum achievable curve is 75mm. A
curve of less than 75mm may stress the PVC
sheath lead to product damage and Electrical
failure.
8) The product should NOT be mounted using staples, nails or metal fixings
which can cause damage to the plastic sheath. Cable ties can be used but
must not be over tightened.
9) Only the connectors supplied are suitable for this product. Further
accessories are available on request. The use of alternative connectors may
lead to poor electrical contact and product damage/failure. A list of these
appears on the foot of this document.
10) The maximum single length that can be run from one power supply is 90m.
11) The LED rope is polarity sensitive and
will only work one way so if the product
does not illuminate switch the contacts
the other way by reversing the
connection. To do this remove the
power lead and rotate 180 Degrees and
re-connect.
Maintenance
Periodically check the product for LED failure and general damage. If any of the LED’s
have failed or the product is damaged in anyway switch off and disconnect from the
mains supply.
To clean the product, switch off and disconnect from the mains supply. Using a
slightly damp cloth gently wipe over. Do not use bleach,
solvent based cleaners or strong detergents. These may
damage the product and invalidate the warranty.
If the mains lead is damaged, it must be replaced by the
manufacturer or and authorised service centre.
If the mains plug needs to be replaced, proceed as follows:
• Connect the brown wire to the terminal labelled "L".
• Connect the blue wire to the terminal labelled "N".
• Make sure that the cord-grip is positioned correctly (over the
outer sheath of the cable) and it fully tightened.
• If the plug is fitted with a 13 A or 5 A fuse, replace it by a 3 A fuse.
DISPOSAL AND RECYCLING
You must not dispose of this item with domestic household waste.
PAT TESTING
When used in an office environment, we recommend that this product should be
safety-tested yearly by a qualified electrician (PAT Tested).
We recommend that it is PAT tested regularly when used in a domestic environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at least once
every 10 years or at every change of occupancy.
For office and retail premises, and buildings such as village halls, the wiring must be
inspected at least once every 5 years.
It is recommended that all building be fitted with smoke alarms (it is mandatory for
new buildings).
List of other available accessories (Not Supplied)
G800AM Inline Coupler
G800AN Mains connector
G800AP End Cap
G800AT Accessory kit
G800AV Power Lead
G803AN 13mm Clip
G803AQ 13mm Channel
G803AS 13mm flexible channel
G803AT 13mm reflective channel
TECHNICAL SPECIFICATION
Voltage ............................................................................... 230V ~ 50Hz
Fuse Rating ......................................................................... 3A
Power Consumption............................................................ 1.8W per m
Tube Diameter .................................................................... 13 mm
Number of LED’s ................................................................. 36 per m
Weight
45m .................................................................................... 10kg
90m .................................................................................... 20kg
SERVICE WARRANTY
Eagle guarantees the product free from defects in materials and workmanship for a period of
twelve months. Should this appliance be operated under conditions other than those
recommended, at voltages other than the voltage indicated on the appliance, or any attempts
made to service or modify the appliance, then the warranty will be rendered void. The product
you buy may sometimes differ slightly from illustrations. This warranty is in addition to, and
does not affect, your statutory rights. Our guarantee is administered by our retailers. If your
product arrives damaged, you must contact the retailer from whom you bought it. The
retailer's contact details will be on the invoice that arrived with the product, or on the e-mail
you received when you placed the order. Do not contact Eagle, only your retailer can arrange a
replacement. If your product fails within the guarantee period, firstly read the "fault finding"
section of this manual, because temperature and weather conditions can affect the
performance of certain products. If the product needs to be repaired or replaced, you must
contact the retailer from whom you bought it. The retailer's contact details will be on the
invoice that arrived with the product, or on the e-mail you received when you placed the
order. If you have just received your product and require technical help in using it, please call
our Help Desk on (0845) 459 4816 If you have any other technical queries about the product,
please call our Help Desk on (0845) 459 4816.
Eagle is a Trademark of Electrovision Ltd.
Lancots Lane, Sutton, St. Helens, Merseyside. WA9 3EX
website: www.electrovision.co.uk
Questo manuale è adatto per i seguenti modelli
11
Indice
Altri manuali Eagle Attrezzatura di illuminazione
