Easee Charge Lite Istruzioni per il montaggio
Charge Lite
EN Installer guide
2
Introduction
Read the Important product information guide in the
product packaging or at easee.com/manuals before
installing the product.
Installation of this product requires a mobile device
with NFC or Bluetooth support.
WARNINGS AND CAUTIONS
A Warning indicates a condition, hazard or unsafe
practice that can result in serious personal injury
or death.
A Caution indicates a condition, hazard or unsafe
practice that can result in minor personal injury or
damage to the product.
WARNING
This product shall only be installed, repaired or
serviced by an authorised electrician. All applicable
local, regional and national regulations for electrical
installations must be respected.
Charge Lite is a home-charging device manufactured
and designed strictly for residential use only. Charge
Lite chargers shall not be used for non-residential
use. Residential use is to be understood as use in or
around an individual’s own residence. The Charge Lite
charger at all times must make use of an individual’s
private connection to the electricity grid. Charge Lite
chargers cannot be used for charging electric vehicles for
which reimbursement is desired, based on the realized
consumption of electricity. The Charge Lite charger
cannot be used to calculate this consumption.
3
Product overview
Installation kit
Strain relief and
front cover
screws (T25)
x 5
Wall screws
(T25)
x 4
Sealing plug
x 2
Blind plug
x 3
Strain relief
x 2
Front cover tool
x 1
Front cover
Protects the electronics from
external influences.
Chargeberry Lite
(1.4–11 kW)
Contains the electronics for
charging the vehicle.
Backplate
(1.4–22 kW)
For attaching and connecting to
the charging infrastructure.
4
Technical specifications
General
Type designation Easee AC Charger Platform CB-A3-2
Dimensions 256 x 193 x 106 mm (H x W x D)
Drilling hole distance c/c 160 x 125 mm (H x W)
Operating temperature -30 °C to +40 °C (indoor and outdoor use)
Weight 1.5 kg
Sensors and indicators
Light strip with LEDs showing the status of the charger
Touch button
Temperature sensors in all main contacts
Chargeberry technical specifications
Max charging power capacity IT 3 phase: 3x 27 A = 6.37 kW
TN 3 phase: 3x 16 A = 11 kW
IT/TN 1 phase: 1x 32 A = 7,2 kW
Connection point Type 2 socket (IEC 62196-2)
Number of phases 1 or 3 (fully dynamic)
Voltage 3x 230/400V AC (±10%)
Mains frequency 50 Hz
Built-in energy meter (±2 %)
Backplate technical specifications
Max charging power capacity 1.4–22 kW
6 A 1 phase – 32 A 3 phase
Up to 7.36 kW at 32 A 1 phase
Up to 22 kW at 32 A 3 phase
Voltage 3x 230/400V AC (±10%)
Mains frequency 50 Hz
5
Connectivity
WiFi 2.4 GHz b/g/n connection
Easee Link RFTM
Control charging via Easee App
RFID/NFC reader
OCPP 1.6 via Easee API
Bluetooth BLE 4.2
Protection
Integrated overload protection according to EN IEC 61851-1:2019
Built-in ground fault protection (30 mA AC/6 mA DC)
External approved Type-A RCD (1 phase: 2P; 3 phase 3P+N; max 40 A) is required
Degree of protection IP54 (the backplate is IP22 without cover)
Impact resistance IK10
Insulation class I
Overvoltage category III
Installation
Installation network TN, IT or TT (detected automatically)
Installation circuit breaker Max 40 A
Short circuit current limited to 10 kA
Wire cross-section Copper wire, between 2.5 and 16 mm2:
1 phase 32 A: 4.0 mm2to 16mm2
3 phase 16 A: 2.5 mm2to 16mm2
Protective earth: minimum 4 mm2
Use the largest possible wire cross-section to make the site future-proof
Cable diameter 8–22 mm
Terminal torque 5 Nm
Cable strip length 12 mm
Notes
Charging station is mode 3 equipment
6
Planning the installation
Prior to the installation, it is recommended that you
consider future charging needs, so that you can easily
expand accordingly in the future.
For an optimal result
— We always recommend a 3 phase installation if
possible, to make it future-proof.
— If possible, use the largest approved cable cross-
section (see Technical specifications).
— Consider installing Easee Ready backplates if there
are plans for adding more chargers in the future.
— To avoid overloading the building's main fuse, the
Easee Equalizer can be used for dynamic load
balancing. The maximum current value can also be
set as required during configuration.
RCDs
Easee Charge Lite shall be installed with an external
Type-A RCD in front of each charge point.1Easee
Charge Lite will disconnect the supply in case of DC
fault currents above 6 mA, thus no external Type-B
RCD is required. The internal DC fault protection is
automatically tested at start-up, between every
charging session or at least every 24 h.
The external RCD is not included with the charger and
must be according to one of the following standards:
— EN 61009-1
— EN 61008-1
— EN 62423
— EN 60947-2
Overcurrent
Easee Charge Lite shall be installed with an external
overcurrent protection device in front of each charge
point. The external overcurrent device is not included
1Easee will continue to challenge the standards and fight to ensure that new and safer technology can gain ground. Until further notice, an
external RCD is required.
with the charger and must be according to one of the
following standards:
— EN 61009-1
— EN 60898
— EN 60947-2
— EN 60269
A combined RCD and overcurrent protection device
(RCBO), according to EN 61009-1, is typically the
preferred choice recommended by Easee for a safe, user-
friendly and cost efficient installation.
NOTES
— RCDs must disconnect all live conductors.
— For manual diagnostic and initialization of the RCD
test, please use the Installer App and diagnostic tool.
Special considerations
— The equipment is intended for non-restricted access.
— The charging station is mode 3 equipment.
— PIN code: The PIN code is required for installation
and located on the front of the Chargeberry. It is
recommended to keep the PIN code for safe keeping,
e.g. inside the fuse cabinet.
— Site Key: During installation, a Site Key must
be used to assign the Charging Robots to the
correct location in the Easee Cloud. A Site Key will
automatically be generated when creating a new
charging site using the Easee Installer App or it can
be obtained by creating a new charging site at
easee.cloud.
CAUTION
This device can emit electromagnetic radiation,
including high-frequency electromagnetic radiation.
7
Your house, power grid and EV
The Charging Robot automatically adapts to the power
grid, the electric car and the capacity of the electrical
installation. In the table you can see what charging
effect you can expect from your installation and
situation. The table is only meant as a guide.
CAUTION
The type of installation as well as cable cross-
sections must be determined by a qualified
electrician in accordance with valid local, regional
and national regulations for electrical systems.
Load Chargeberry power (Charge Lite)
Ampere (A) 1 phase (kW) 3 phase (kW)2
6 1.4 4.1
8 1.8 5.5
10 2.3 6.9
13 3.0 9
16 3.7 11
20 4.6 –
25 5.8 –
32 7.4 –
Padlock
It is possible to lock the electronics with a padlock. This
will create an extra layer of security (padlock is not
included).
Max total lock height 56 mm
Shackle height (outer dimensions) 19 - 20 mm
Shackle thickness 3.2 - 4 mm
2Example for 400 V TN, deviating values for other grid types.
8
WARNING
Always work with the power off and in
accordance with local regulations. Use
extreme caution and follow instructions
carefully.
Installation
instructions
Bend down the lower part of the rubber cover and
insert the two ends of the front cover tool into the
two openings at the bottom of the front cover.
Pull the tool until the front cover comes loose and
remove the cover.
Grasp the Type 2 socket and push upwards with
good force until the Chargeberry disconnects. Make
sure you do not touch the cable locking mechanism.
1
2
3
1
1
2
2
3
Opening
Charging Robot
1
9
Fix the backplate to a solid, non-perforated wall
or structure with sufficient load-bearing capacity
using the 4 wall screws provided in the mounting kit.
Use suitable wall plugs for mounting and observe
the local regulations for recommended installation
height.
CAUTIONS
— The installation wall must cover the entire back of
the product. If this is not possible to achieve, it is
possible to use the Easee Mount.
— The area should not be exposed to direct rain, direct
sunlight or explosive gases. A physical barrier is
recommended to protect the charger.
— Install at a height of 130–140cm, with an angle no
more than +/- 3 degrees from vertical. Suggested
installation height for accessibility: 80–95 cm.
1
Backplate
Mounting
2
1
1
Fuse box / enclosure
Adding external
protection
3
External Type A RCD protection is required for each
backplate with Charge Lite. The RCD must meet the
regulations and requirements stated in Planning the
installation.
NOTE
If you will have multiple charging points at the same
time, you must have a requisite external Type A RCD
protection for each backplate with an Charge Lite
charger. Examples can be found at support.easee.com.
1
x 4
1
1
Installation height
10
Backplate
Preparing
4Shorten the sealing plug to fit the cable. The hole
should be slightly smaller than the cable to ensure
a good seal.
Insert the cable through one of the 4 cable entries
and secure it to the backplate with the strain relief
provided.
Close all cable entries that are not in use with the
supplied blind plugs.
1
2
3
1 2
3
33
1
x 1
2
x 2
3
x 3
Indice
Altri manuali Easee Caricabatterie per batterie
Easee
Easee Charging Robot Istruzioni per il montaggio
Easee
Easee Ready Istruzioni per il montaggio
Easee
Easee Ready Guida alla risoluzione dei problemi
Easee
Easee Home Guida alla risoluzione dei problemi
Easee
Easee Equalizer Amp Guida utente
Easee
Easee Chargeberry Manuale utente
Easee
Easee Charge Manuale utente
Easee
Easee Equalizer Manuale utente
Easee
Easee One Manuale utente
Easee
Easee Equalizer Manuale utente
