EasyLinkin G500 Manuale utente

G500 Gateway
User Manual

©2018 Easylinkin Co.,Ltd
2
1. Gateway Package
1.1 Package Content
Each gateway is shipped with the following items:
Item
Photo
Name
Quantity
Remarks
1
G500 Gateway
1
2
GPS Antenna
1
3
GPS Feeder
1
4
4G/WiFi Antenna
1 or 2
Ethernet version: 1
4Gversion: 2
5
N Connector
1 or 2
Ethernet version: 1, 4G
version: 2
6
Omni-directional
Antenna
1
Optional
7
RF Feeder
1
Optional
8
Directional Panel
Antenna
1
Optional
9
Wall Mounting Bracket
for Gateway
1
Optional
10
Pole Mounting Bracket
for Gateway
1
Optional

©2018 Easylinkin Co.,Ltd
3
11
Pole Mounting Bracket
for Antenna
1
Optional
12
PoE Adaptor
1
Optional
13
Industrial Din-rail
Power Supply
1
Optional
14
Switching Power
Supply
1
Optional
15
USER MANUAL
1
16
DATESHEET
1
17
CERTIFICATE,
WARRANTY CARD
1
1.2 Unpacking the Gateway
The gateway and accessories are placed in two layers in the carton.
Ensure that all items listed in the Package Contents section are included in the carton.
Check each item for possible physical damage.
If any item is damaged or missing, please notify EasyLinkin sales.

©2018 Easylinkin Co.,Ltd
4
2. Ports Introduction
Ports:
NOTE: For single-channel gateway, RF1 port is plugged up as shown below. (RF1 port with a red
circle)
.
Side panel:

©2018 Easylinkin Co.,Ltd
5
3. Installation Guide
3.1 Mounting Modes
Pole Mounting Wall Mounting
Two different mounting modes:
Pole mounting: Attach the gateway (and power supply) to bracket for gateway (Item 10)and the
antennas to the bracket for antenna (Item 11), then mount two brackets to the pole through derrick.
Gateway position can be adjusted flexibly according to deployment location.
Wall mounting: Attach the gateway to bracket (item 9), then mount the bracket to the wall with
expansion screws. Antenna can be installed separately.

©2018 Easylinkin Co.,Ltd
6
Choose the installation mode that is a better fit to the surrounding environment and construction
requirements.
3.2 Precautions
Please pay attention to the following notes when installing and using gateway:
The gateway way should be mounted high on the location with no obstructions.
Lightning protection is recommended for all installations.
Different antennas can be chosen (Omni-directional antenna or directional antenna) depending on
environment.
Municipal power supply is required in installation site.
Broadband access is required in installation site.
The gateway can choose to use Omni-directional or directional antenna according to the surrounding
environment.
Installation of the gateway must be done by professionals and shall strictly comply with construction
requirements for communication equipment.
4. Connections
4.1 Connecting to the GPS Antenna
The GPS antenna kit includes a GPS antenna and a feeder.
GPS antenna kit
Feeder: Double trimming N Female to N-Male, RG-58 impedance (50Ω).
Follow these steps to connect GPS antenna to gateway:
Step 1: Connect the N-Female of feeder to GPS antenna.
Step 2: Connect the N-Male of feeder to gateway.

©2018 Easylinkin Co.,Ltd
7
Installation instructions:
Location requirements
Make sure there is at least 90°clearance upward and it can track satellites as many as possible, at least
4 satellites.
90°clearance upward air
Keep the feeder as short as possible to reduce signal loss.(The longer the feeder, the greater the signal
loss will be)
For tower installation, keep the horizontal distance between the mounting pole and the tower at least 30
cm.
GPS antenna should not be installed under the microwave antenna, the high-voltage wire or the TV
transmitting tower. It should not be exposed to the main lobe radiation of the mobile antenna.
Keep antenna lower than the lightning rod and under its protection zone.
When GPS antenna is installed on the top of the building, do not install the antenna in the position
where the two sides of the floor intersect.
GPS feeder requirements:
Length is from 80m to 100m, choose 1/4" feeder
Length is from 100m to 120m, choose 1/2" feeder

©2018 Easylinkin Co.,Ltd
8
Length exceeds 120m, choose 7/8" feeder
Length is less than 80m, choose Φ9 feeder
4.2 Connecting to the WiFi Antenna
The WiFi antenna kit includes a 0.16mi white fiberglass epoxy WiFi antenna and a N connector ( N-J to
N-K 90°right-angle elbow connector).
Follow these steps to connect Wi-Fi antenna to gateway,
Step 1: Connect the N Female of connector to WiFi antenna.
Step 2: Connect N Male of connector to gateway.
..
4.3 Connecting to the 4G Antenna
The 4G antenna kit includes a 0.16m white fiberglass epoxy WiFi antenna and a N connector ( N-J to N-
K 90°right-angle elbow connector).
Follow these steps to connect 4G antenna to gateway:
Step 1: Connect N Female of connector to 4G antenna.
Step 2: Connect N Male of connector to gateway.

©2018 Easylinkin Co.,Ltd
9
Note: Other antennas with different length such as 0.6m/0.9m can be selected according to different
application requirements.
Antenna specification
White fiber glass epoxy Omni-directional antenna, gain 4.6/6.5dBi, N female connector
RF feeder
Various feeders can be proposed to adapt to environment and gateway configurations. Typically N-J to
N-J, SYV50-7 (50Ω) with internal screws used.
4G antenna and RF feeder in the standard package can be used directly for demo or test purpose. The
selection of the antenna and RF feeder should depend on the project requirement.
No load at the antenna port for high-power equipment is strictly forbidden, which will void the
warranty and may cause severe damage to RF circuitry.

©2018 Easylinkin Co.,Ltd
10
4.4 LoRa Antenna
Selection of Omni-directional antenna or directional antenna can be decided according to the environment.
Below is the common connection.
4.4.1. LoRa Omni-directional Antenna + Feeder
Antenna
White fiberglass epoxy Omni-directional antenna, gain 5dBi, N Female port.
Feeder:
Various feeders can be proposed to adapt to environment and gateway configurations.
Common choice: N-J to N-J, internal screw, SYV50-7 (50Ω).
LoRa antenna and RF feeder in the standard package can be used directly for demo or test purpose. The
selection of the antenna and RF feeder should depend on the site condition and project requirement.
Indice
Altri manuali EasyLinkin Portale
Manuali Portale popolari di altre marche

LST
LST M500RFE-AS Manuale utente

Kinnex
Kinnex Media Gateway Manuale utente

2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey
Telsey CPVA 500 - SIP Manuale utente












