Easymount SIGN Manuale utente

Questo manuale è adatto per i seguenti modelli

1

Altri manuali Easymount Plastificatrice

Easymount

Easymount EM-S880 Scheda tecnica

Easymount

Easymount EMS-650 Scheda tecnica

Easymount

Easymount EM-1200 Scheda tecnica

Easymount

Easymount EM-1200DH Scheda tecnica

Easymount

Easymount Single Hot EM-1600SH Scheda tecnica

Easymount

Easymount Air EM-A1600SH Scheda tecnica

Easymount

Easymount Cold EM-1400 Manuale utente

Easymount

Easymount Sign EM-S1400C Scheda tecnica

Easymount

Easymount Sign EM-720 Scheda tecnica

Manuali Plastificatrice popolari di altre marche

Renz

Renz HT 330 L Manuale utente

Gfp

Gfp 44TH Manuale utente

Lapis

Lapis Lamina006 Manuale utente

Hama

Hama L44B Manuale utente

PAVO

PAVO FLORIDA Manuale utente

M-Triangel

M-Triangel MT-102 Manuale utente

Akiles

Akiles PROLAM 230 Manuale utente

D&K

D&K Masterpiece 550 Manuale utente

Falcon

Falcon F-40 Manuale utente

LEITZ

LEITZ EasyLaminator A4 Manuale utente

LEITZ

LEITZ coldLAM CS9 Manuale utente

kala

kala Starter 1080 Manuale utente

Fellowes

Fellowes Venus A3 Manuale utente

Qomolangma

Qomolangma FMJ-1400-WA-PLUS Manuale utente

Opus

Opus Coverator 330 Manuale utente

ALDI

ALDI OL 250-L Manuale utente

Phoenix

Phoenix 2700-DH Manuale utente

acropaq

acropaq AL-3400 Manuale utente

ASSEMBLY

INSTRUCTIONS

In your stand box you should have the below parts:

The Middle Support Beam is Slightly Longer than the Top.

Using 4 x longer bolts, attach the bottom support beam to the left and right stand frames.

Using 4 x smaller bolts, attach the middle support beam [this is the longest support bar].

Using the Last 4 x Longer bolts attach the top support beam.

Ensure all bolts are tightened fully and place the 2 x mandrels in the holders.

Place the Laminator on the stand.

The Parts left in your Machine Crate are Below [excluding the lifting handle bag and Elements].

Attach the Left and Right Mandrel Support holders to the machine using the bolts supplied and place

the mandrels in the supports as shown in the pictures below.

Remove Left and Right side covers off the laminator.

Remove the rubber sport below and Insert the Quartz Heating Element. Once Element is fitted

please return the element support back into position.

Remove the Green Rubber sleeve on the left and right and attach the wire to each end of the

element, ensuring there is a washer either side of the terminal as shown in the pictures below.

Place end caps back on to the element.

Move the laminator to where the machine will be situated, please note all 4 wheels must be on a

level floor for the roller pressure to be level.

To check the roller pressure, place a small piece of card in the centre of the roller and lower the

roller down. Once in the down position check the gap in between the rollers on the left and right,

these should be the same, if not please see the next page.

If the rollers are level, please put the side covers back onto the laminator.

Once the side covers are on please put the lifting handle and key in place and secure using the bolt

provided.

Easymount Sign: Adjustment of Roller Gap & Pressure

1).

Using a 2.5mm Allan-key undo the 6 screws to take the left side panel of the machine.

2).

Take off the emergency stop button by unscrewing the screw above.

3).

Take off the screw and large washer above.