Eaton S611 Manuale

Installation Leaet IL03901007E Effective June 2011

S611 User Interface Remote Mounting

Installation Leaﬂet

Disconnect power in accordance with federal, state, and local codes and remove the S611 from the enclo-

sure or mounting panel.

NOTE: Servicing the S611 while installed in an enclosure or mounted vertically on a panel is not recom-

mended.

Place the unit on a clean work surface.

Cover Removal

1. Disconnect all control wiring and tie wraps securing any wiring to the cover assembly.

2. Remove cover screws with nuts. 6 each on Frames A – D, 4 each on Frames E - F.

NOTE: Cover screw nuts are prevented from rotating but are not retained in place by the pole

supports. Do not allow hardware to fall into the soft starter.

3. Lift top of cover approximately 6” to gain access to the BYPASS VOLTAGE contactor

connector mounted on the Printed Circuit Board (PCB). See Figure 1.

4. Press locking tab on BYPASS VOLTAGE contactor connector and disconnect from the PCB.

5. Carefully rotate cover to rest onto work surface as shown. See Figure 2.

Figure 1 - Contactor Connector Figure 2 - Cover Position

Mounting The Remote Display

If necessary, remove the User Interface from the cover using a 30mm pilot device tool (E22CW recom-

mended).

1. Drill or punch two 30mm pilot holes on 1.75-inch centers a minimum of 1.60 inches (40.6 mm)

from every door gasket (see Figure 3).

2. Insert remote display through the door and add two gaskets provided behind the door

(see Figure 4).

Installation Leaet IL03901007E

Effective June 2011

S611 Soft Starters

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL03901007E

June 2011 Rev.001

PowerChain Management is a registered

trademark of Eaton Corporation.

All other trademarks are property of their

respective owners.

Figure 3 - Pilot Device Holes - Inch[mm]

Minimum to all

gaskets ordoor

mounteddevices

1.60

[40.6]

1.75

[44.5]

Gaskets

E22CW

Tighten

Figure 4 - Door Cut Away For Clarity

3. Orient strain relief bracket with respect to your chosen cable routing.

4. Add two jam nuts provided and tighten 30mm pilot device tool until the strain relief bracket is

flush with the enclosure door, tighten an additional ½ of a turn.

Connecting the Remote Display

1. Route cable from User Interface to PCB (see Figures 5 & 6).

2. Secure cable to the strain relief bracket using any suitable tie wrap.

3. Reinstall cover assembly.

Figure 5 - Interconnecting Cable - PCB Figure 6 - Interconnecting Cable - User Interface

Cover Reinstallation

1. As the cover is placed onto the supports, carefully guide wiring into place.

2. Ensure that the BYPASS VOLTAGE contactor connector is properly connected prior to installing

the cover screws.

3. Install and torque all cover assembly screws to 22 – 27 lb-in.

4. Reinstall control wiring.

Altri manuali per S611

Indice

Altri manuali Eaton Controllori

Eaton

Eaton xComfort CRCA-00/10 Manuale di istruzioni

Eaton

Eaton CGLine+ Web-Controller Manuale utente

Eaton

Eaton Cutler-Hammer Jockey Manuale utente

Eaton

Eaton EMS Series Manuale utente

Eaton

Eaton xComfort CSAP-01/XX Manuale utente

Eaton

Eaton xComfort CSAU-01/01-10 Manuale utente

Eaton

Eaton xComfort CDAE-01/01 Manuale utente

Eaton

Eaton ADS8 Series Manuale

Eaton

Eaton ELC-PB Manuale del proprietario

Eaton

Eaton SCD24 Manuale utente

Eaton

Eaton EFX48 e-Fuse Series Istruzioni operative

Eaton

Eaton xComfort CSEZ-01/07 Manuale utente

Eaton

Eaton Vikers V200 Series Manuale utente

Eaton

Eaton AMPGARD RVSS Manuale operativo e di manutenzione

Eaton

Eaton EPCT Fire Series Manuale utente

Eaton

Eaton EMS-SWD Series Manuale utente

Eaton

Eaton C441 Series Manuale utente

Eaton

Eaton LMR PLUS Manuale utente

Eaton

Eaton Vickers SMC20 Manuale utente

Eaton

Eaton DS7-34 SX041N0 Series Manuale

Eaton

Eaton Cutler-Hammer Easy-Start ES Series Manuale utente

Eaton

Eaton xComfort Room Controller Touch Manuale utente

Eaton

Eaton COOPER POWER SERIES Manuale di servizio

Eaton

Eaton PKZM01 Series Manuale

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente