Eaton Powerware 9355 Manuale utente
Powerware Series
Eaton 9355 Tie Cabinet
Installation Guide
For use with Eaton®9355 20/30 kVA UPSs
®
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment Regulations ICES‐003.
Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du Canada.
IEC 62040-2
Some configurations are classified under IEC 62040-2 as “C2 UPS for Unrestricted Sales Distribution.”
Eaton, Powerware, Powerware Hot Sync, and X-Slot are registered trademarks of Eaton or its subsidiaries and affiliates. Greenlee is a registered
trademark of Greenlee Textron. National Electrical Code and NEC are registered trademarks of National Fire Protection Association, Inc. All other
trademarks are property of their respective companies.
ECopyright 2006–2015 Eaton, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the express
written approval of Eaton.
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such
as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This product
contains sealed, lead‐acid batteries and must be disposed of properly. For more information, contact your
local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the
trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
ON - Indicates that the switch is in the ON position.
OFF - Indicates that the switch is in the OFF position.
PHASE - The word “phase.”
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality i
Table of Contents
1 Introduction 1........................................................
2 Safety Warnings 3....................................................
3 Tie Cabinet Installation 7...............................................
4 Installing Options 19...................................................
Powerware Hot Sync CAN Bridge Card 19....................................................
5 Service and Support 27.................................................
6 Warranty 29..........................................................
Limited Factory Warranty 29..............................................................
TABLE OF CONTENTS
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality
ii
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality 1
Chapter 1 Introduction
A Tie Cabinet can be installed as a wall-mounted bypass or to provide support for a
parallel system for redundancy or extra capacity.
A wall-mounted bypass switch is used to bypass the UPS during maintenance or
servicing, providing wrap-around bypass for UPS service without shutting down the
load.
A parallel (load sharing) system provides more capacity than a single UPS and can
provide backup, depending on the load and configuration. In addition, when one UPS
is taken out of service for maintenance or is not operating properly, a redundant UPS
continues to supply uninterrupted power to the critical load. A parallel Powerware Hot
Sync®CAN Bridge Card provides connectivity for system metering and operational
mode control. The parallel system consists of two to four UPSs, each with a parallel
CAN Bridge Card and a parallel cabinet.
Figure 1 shows the Eaton 9355 UPS.
Figure 1. The Eaton 9355 UPS
INTRODUCTION
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality
2
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality 3
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and maintenance of
the UPS and batteries. Please read all instructions before operating the equipment and save this manual for
future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED
SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.
WARNING
SThis UPS contains its own energy source (batteries). The UPS output may carry live voltage even when
the UPS is not connected to an AC supply.
STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity controlled,
indoor environment, free of conductive contaminants. Ambient temperature must not exceed 40°C
(104°F). Do not operate near water or excessive humidity (95% maximum).
STo reduce the risk of fire, connect only to a circuit provided with 125 amperes maximum branch circuit
overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70.
SOutput overcurrent protection and disconnect switch must be provided by others.
CAUTION
SBatteries can present a risk of electrical shock or burn from high short circuit current. Observe proper
precautions. Servicing should be performed by qualified service personnel knowledgeable of batteries
and required precautions. Keep unauthorized personnel away from batteries.
SProper disposal of batteries is required. Refer to your local codes for disposal requirements.
SNever dispose of batteries in a fire. Batteries may explode when exposed to flame.
SAFETY WARNINGS
Eaton 9355 Tie Cabinet (20/30 kVA) Installation Guide S164201630 Rev D www.eaton.com/powerquality
4
Consignes de Sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute procédure
d'installation et de maintenance des batteries et de l'onduleur. Veuillez consulter entièrement ces
instructions avant de faire fonctionner l'équipement et conserver ce manuel afin de pouvoir vous y reporter
ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d'entretien et de réparation doit être
EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ. AUCUNE PIÈCE RÉPARABLE PAR
L'UTILISATEUR ne se trouve dans l'onduleur.
AVERTISSEMENT!
SCette onduleur possède sa propre source d'alimentation (batteries). Il est possible que la sortie de
l'onduleur soit sous tension même lorsque l'onduleur n'est pas connectée à une alimentation CA.
SPour réduire les risques d'incendie et de décharge électrique, installer l'onduleur uniquement à
l'intérieur, dans un lieu dépourvu de matériaux conducteurs, où la température et l'humidité ambiantes
sont contrôlées. La température ambiante ne doit pas dépasser 40 °C. Ne pas utiliser à proximité d'eau
ou dans une atmosphère excessivement humide (95 % maximum).
SAfin de réduire les risques d'incendie, n'effectuez le raccordement qu'avec un circuit muni d'une
protection de surintensité du circuit de dérivation maximum de 125 ampères conformément au Code
Électrique National (National Electrical Code) des États-Unis ANSI/NFPA 70.
SLa protection de surintensité de sortie ainsi que le sectionneur doivent être fournis par des tiers.
ATTENTION!
SLes batteries peuvent présenter un risque de choc électrique ou de brûlure provenant d'un courant de
court-circuit haute intensité. Observez les précautions appropriées. L'entretien doit être réalisé par du
personnel qualifié connaissant bien les batteries et les précautions nécessaires. N'autorisez aucun
personnel non qualifié à manipuler les batteries.
SUne mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements en vigueur dans
votre localité.
SNe jamais jeter les batteries au feu. L'exposition aux flammes risque de les faire exploser.
Altri manuali per Powerware 9355
8
Indice
Altri manuali Eaton UPS
Eaton
Eaton EX Pulsar Series Manuale utente
Eaton
Eaton 9SX 6000VA Manuale utente
Eaton
Eaton Ellipse MAX 600 Manuale utente
Eaton
Eaton Ellipse ECO 500 Manuale utente
Eaton
Eaton 9SX 15K Series Manuale utente
Eaton
Eaton Powerware 9130 Manuale utente
Eaton
Eaton EX 2200 RT 3U Manuale utente
Eaton
Eaton Powerware 9x55 series Manuale
Eaton
Eaton Powerware 9140 Manuale utente
Eaton
Eaton FerrUPS FE Manuale utente
Eaton
Eaton Powerware 9395 Manuale utente
Eaton
Eaton PowerRite XT PRXT-0400A Manuale utente
Eaton
Eaton Powerware 9395 Manuale
Eaton
Eaton 9SX Series Manuale utente
Eaton
Eaton Power Xpert 9395 550/275 Manuale utente
Eaton
Eaton BladeUPS none Manuale utente
Eaton
Eaton Powerware 5125 Manuale utente
Eaton
Eaton DIN500AC Istruzioni per il montaggio
Eaton
Eaton 5S 1000 Manuale utente
Eaton
Eaton Power-Sure 700 Manuale utente
Manuali UPS popolari di altre marche
Pylontech
Pylontech Victron & Pylontech US5000 Manuale utente
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuale utente
Mecer
Mecer ME-1000-WTU Manuale utente
Mustek
Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento
Emerson
Emerson Liebert NXL series Manuale utente
MAKELSAN
MAKELSAN BOXER SERIES Manuale utente
