EBN Technology WTM60-8B-VR Manuale utente
User’s Manual
WTM 60 Series
Copyrights i
Copyrights
©2009 All rights reserved. The information in this
document is subject to change without prior notice in
order to improve reliability, design and function and does
not represent a commitment on the part of the
manufacturer.
This document contains proprietary information
protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any
mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
All trademarks are property of their respective
owners
Liability Disclaimer
In no event will the manufacturer be liable for direct,
indirect, special, incidental, or consequential
damages arising out of the use or inability to use the
product or documentation, even if advised of the
possibility of such damages.
Regulatory Information
FCC Notices
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the Federal Communications Commission
(FCC) Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or
television technician for help.
This device complies with Part 15 (B) of the FCC
Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference
and
2) this device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS DEVICE. SUCH
MODIFICATIONS COULD VOID THE USER'S
AUTHORITY TO OPERATE THE DEVICE.
CE Notice
This device complies with EMC Directive
2004/108/EC issued by the Commission of the
European Community.
Copyrights
ii
WEEE Notice
The WEEE mark applies only to countries within the
European Union (EU) and Norway.
This appliance is labeled in accordance with
European Directive 2002/96/EC concerning waste
electrical and electronic equipment (WEEE). The
Directive determines the framework for the return
and recycling of used appliances as applicable
throughout the European Union. This label is applied
to various products to indicate that the product is not
to be thrown away, but rather reclaimed upon end of
life per this Directive.
Contents iii
Contents
Copyrights .................................................................................................i
Liability Disclaimer ...................................................................................i
Regulatory Information.............................................................................i
FCC Notices.......................................................................................................... i
CE Notice .............................................................................................................. i
WEEE Notice........................................................................................................ ii
Contents...................................................................................................iii
Hardware Setup........................................................................................4
3.1. Quick Tour............................................................................................... 4
Front View...................................................................................................... 4
Back View ...................................................................................................... 5
Back Panel I/O ............................................................................................... 6
Hardware Setup........................................................................................7
LR Series ....................................................................................................... 7
VR Series....................................................................................................... 7
Touch Screen Driver and Utility Installation ..........................................8
4.1. Before the installation.................................................................................. 8
4.2. Touch Panel Driver Installation ................................................................... 8
Specification...........................................................................................12
Chapter 1
4
1.
Hardware Setup
3.1. Quick Tour
Front View
WTM60-8B-VR/ WTM60-8B-LR
WTM60-2B-VR/ TM60-2B-LR
WTM60-5B-VR/W WTM60-5B-LR
LED Indicator
The Power indicator will glow green when power is on.
N/A
N/A
Chapter 1 5
Back View
WTM60-8B-LR/ WTM60-8B-VR
WTM60-2B-LR /WTM60-2B-VR
WTM60-5B-LR /WTM60-5B-VR
Chapter 1
6
Back Panel I/O
LR Series (WTM60-8B-LR / WTM60-2B-LR / WTM60-5B-LR)
VR Series (WTM60-8B-VR / WTM60-2B-VR / WTM60-5B-VR)
Chapter 2 7
2.
Hardware Setup
LR Series
1. Connect the one connector of the LVDS cable to the LVDS port on the
back panel of the WTM 60, another connector to your POS device.
2. Connect the one connector of the audio cable to the audio-in jack on the
back panel of the WTM 60, another connector to your POS device.
VR Series
1. Connect the one connector of the VGA cable to the VGA port on the back
panel of the WTM 60, another connector to your POS device.
2. Connect the one connector of the audio cable to the audio-in jack on the
back panel of the WTM 60, another connector to your POS device.
Chapter 3
8
3.
Touch Screen Driver and Utility Installation
4.1. Before the installation
For CD-ROM onboard model:
1. Insert the driver CD into the onboard CD-ROM drive. The program
autoruns and displays the DRIVER BANK screen.
2. Follow the on-screen instructions.
For Model without CD-ROM Onboard:
1. Connect an external USB CDROM to the USB power and insert the driver
CD and turn on the device. The program autoruns and displays the DRIVER
BANK screen.
2. Follow the on-screen instructions.
4.2. Touch Panel Driver Installation
1. Click TM/WTM Series.
2. Click Touch Driver
Chapter 3 9
3. Click HIGGSTEC TOUCH PANEL.
4. Click “Next” button.
5. Click “Browse” to select the location where the driver installed, and then
click “Next”. Or you can click “Next” go to next screen directly.
Questo manuale è adatto per i seguenti modelli
7
Indice
Altri manuali EBN Technology Pannello touch
