Ebyte E18-TBHL-01 Manuale utente
Chengdu Ebyte Electronic Technology Co.,Ltd. E18-TBHL-01 User Manual
Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co.,Ltd. 1
E18-TBL-01 User manual 1.1
1、Brief introduction
1. Used to test and develop E18 zigbee modules (E18-MS1-PCB, E18-MS1-IPX, E18-MS1PA1-PCB,
E18-MS1PA1-IPX).E18-TBL-01 has been pre-welded with E18-MS1-PCB. For details, see the module
manual.
2. All IO ports of E18 series have been led out.
3. Designed with CH340G UART chip, UART communication development is available.
4. Designed with USB interface, can connect with your PC directly.
5. User can connect the external power supply and UART directly for secondary development.
Chengdu Ebyte Electronic Technology Co.,Ltd. E18-TBHL-01 User Manual
Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co.,Ltd. 2
2、User guide
Definition：
①
UART TXD selection port (P1.4)
②
UART RXD selection port (P1.5)
③
External 5V power supply port
④
External 3.3V power supply port
⑤
Module running indicator
⑥
Networking indicator
⑦
Power indicator
⑧
RLED selection port (P1.3)
⑨
NLED selection port (P1.2)
⑩
Mode selection port (P1.6)
⑪
SOC selection port (chip VCC)
⑫
Reset button for baud rate(P1.7)
⑬
Reset button
Chengdu Ebyte Electronic Technology Co.,Ltd. E18-TBHL-01 User Manual
Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co.,Ltd. 3
Function description：
1.Reset button is for system reset.
2. Double click baud rate rest button is for baud rate rest (default 115200bps)（P1.7）
Note: Press the baud reset button before powering on the new firmware module. Release the button after
powering on the new firmware module.
3.TXD,RXD selection port can used to connect with external UART.
4.Mode selection port: The old firmware is used to switch between AT and HEX instruction modes. When
the jumper cap is inserted, it represents HEX instruction mode (low level), while when the jumper cap is not
inserted, it represents AT instruction mode (high level) (P1.6). Note: The new firmware does not support AT
instruction mode and can be suspended (P1.6).
5. Port ①、②、③、④、⑧、⑨、⑩, and ⑪are used together to test the module current. Without
jumper plugged in for port ①、②、③、④、⑧、⑨、⑩ and ⑪, the galvanometer pen contacts ⑪ports
(above: left positive and right negative), can test the chip current.
3、Driver installation
Please visit our website for downloading CH3410G（Click here for download）. After the
installation is complete, the serial port number can be identified in the device.
4、Program download
Built-in 8051 MCU, for program download, pls use our CC-DeBugger, UART or other JTAG, ISP,
ICP instruments are not available.
The compiled HEX file is available for downloading directly.
5、Technical assistance
Chengdu Ebyte Electronic Technology Co.,Ltd. E18-TBHL-01 User Manual
Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co.,Ltd. 4
6、Communication test
Altri manuali Ebyte Hardware per computer
Ebyte
Ebyte E72-2G4M20S1C-TB Manuale utente
Ebyte
Ebyte ESP32-C3-MINI-1U Manuale utente
Ebyte
Ebyte ECAN-W01 Manuale utente
Ebyte
Ebyte E180-ZG120A Manuale utente
Ebyte
Ebyte E15-USB-T2-V2.0 Manuale utente
Ebyte
Ebyte E18-TBH-01 Manuale utente
Ebyte
Ebyte K62-DL20 Manuale utente
Ebyte
Ebyte E43-900T13S3 Manuale utente
Ebyte
Ebyte MBL Series Manuale utente
Ebyte
Ebyte E831-RTU Series Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
