Echoflex Elaho Dual Tech Ceiling-mount Vacancy Sensor Manuale utente

Echoflex Installation Guide

Elaho Dual Tech Ceiling-mount Vacancy Sensor

Main Office nSquamish, BC, Canada nToll Free +888 324 6359 nPhone +778 733 0111 nFax +604 815 0078

Email info@echoflexsolutions.comnWeb: echoflexsolutions.comnProduct information and specifications subject to change.

8186M2184 nRevision A nReleased 2018-09

Overview

The Elaho Dual Tech Ceiling-mount Vacancy Sensor uses passive infrared (PIR)

technology and acoustic detection to provide reliable vacancy sensing for

lighting control. The sensor relies on local station control for manual on and

provides auto off functionality upon detection of vacancy.

The ceiling-mount sensor offers 360 degree coverage with optimized lens

options to accommodate small and large spaces. The sensor is available in a

white or black finish.

Small Room Lens - coverage

•

452 ft2at 8 ft (42 m2at 2.4 m)

•

804 ft2at 10 ft (74.3 m2at 3 m)

Large Room Lens - coverage

•

1,809 ft2at 8 ft (168 m2at 2.4 m)

•

3,019 ft2at 10 ft (280 m2at 3 m)

Field-installed lens masks are provided to allow customized detection fields

for each sensor lens type.

Custom Configuration

This document guides you through the installation and local DIP switch setup

of the sensor.

For more detailed information about custom configuration options available

using ElahoAccess, see the ElahoAccess Mobile App integrated help system.

Note: To use the configuration settings applied using ElahoAccess, DIP

switch 2 must be enabled. See DIP Switch Settings on page7.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Prepare for Installation

Ceiling-mount sensors are intended for installation to a finished ceiling

surface, soft ceiling tile mounted, or attached to a round or octagonal fixture

junction box.

Compliance

•

UL/cUL listed, complies with UL508A, UL916, and CSAC22.2 No.14

•

CE compliant

For use with Echoflex dimming and relay products.

Environment

Ambient

For indoor, commercial controls use only. Indoor installation only. The sensor

operates in ambient temperatures of -10°C to 40°C, with a maximum of

90% non-condensing humidity.

Installation

Echoflex recommends paying special attention to the installation

environment:

•

When operating in PIR only modes, the sensor must have an

unobstructed view of the room. Do not mount behind or near tall

cabinets, shelves, hanging light fixtures, etc.

•

Do not install the sensor within eight feet from an HVAC airflow

duct/vent.

•

Install the sensor where it cannot easily sense movement in areas

outside of the intended space, such as hallways, glass partitions, or

adjacent rooms. If the installation location cannot avoid these

conditions, portions of the lens can be masked to block the sensor

view of these undesired areas. See

Lens Masking on page10

Note: In areas of increased noise activity, enabling PIR only mode may

allow for better occupancy detection results. See DIP Switch Settings on

page 7.

Dual Tech Ceiling-mount Vacancy Sensor Page 2 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Control Wire Specification

The sensor connects to the EchoConnect®communication bus. EchoConnect is

a bidirectional protocol that uses one pair of wires (data+ and data-) for both

data and power. Echoflex recommends using Belden 8471 (or approved equal)

Class 2 wire. The total combined length of an EchoConnect wire run (using

Belden 8471, or equal) may not exceed 1,640feet (500m).

Note: All control wiring should be installed and terminated by a

qualified installer and should follow standard wiring installation practices.

Leave approximately 8" (20cm) of wiring in the back box for connection

and to allow slack for future service needs.

Note: Echoflex requires that all Elaho stations and devices be grounded

for ESDprotection. Pull an additional 14AWG (2.5 mm2) wire for

grounding when control wires are not installed in grounded metal conduit.

Note: When using Category 5 (or equivalent) cable on the EchoConnect

communication bus, please note the following:

•

Cat5 wiring must be terminated using EchoConnect Cat5

Termination Kit and must be installed using a bus topology.

Refer to the installation guide that is provided with the Cat5

Termination Kit (8186A1207) for information to terminate

Cat5 wiring.

•

Not all topologies are supported using Cat5; careful planning

is required to ensure the proper termination kits are available

and the wire is pulled appropriately.

Parts and Supplies

The following parts and supplies are included with the sensor:

•

soft ceiling tile adapters

•

2 each screws, 6-32 x 3/4” and 1 3/4”

•

lens masks

•

WAGO connectors (wire termination connectors)

Dual Tech Ceiling-mount Vacancy Sensor Page 3 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Installation

Installation should follow all local codes and standard electrical practices.

Note: NEC Class 2 product to be wired in accordance to NEC Article

725 and local jurisdiction requirements.

The ceiling-mount sensor is provided with a mounting plate that can be

mounted to a junction box, finished ceiling, or soft ceiling tile. Determine the

installation method and follow the detailed instructions:

•

Junction Box or Surface Installation below

•

Soft Ceiling Tile Installation on the facing page

Junction Box or Surface Installation

1. Pull the Belden 8471 (or

equivalent) and one 14 AWG

(2.5 mm2) ground wire to the

mounting location (junction

box or finished surface) and

strip each wire 3/8” (9–

10mm).

2. Temporarily remove the

sensor cover to gain access to

the configuration switches

and mounting access holes.

Hold the sensor in one hand

while gently twisting the

cover clockwise.

3. Connect the EchoConnect

wires from the sensor to the

installed wires.

a. Connect the data - (typically black) EchoConnect wire from

sensor to the incoming EchoConnect (typically black) wire using a

WAGO wire termination connector.

b. Repeat the above step for the data + (typically white)

EchoConnect wire and for the ESD ground wire, using a new

WAGO connector for each termination type.

4. Orient the flat side of the sensor to the junction box or surface and

secure it in place using the screws provided (both short and long

screws are provided for installation convenience).

Dual Tech Ceiling-mount Vacancy Sensor Page 4 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Soft Ceiling Tile Installation

Ceiling tile

adapter Ceiling tile

Ceiling tile adapter

1. Pull the Belden 8471 (or equivalent) and 14 AWG (2.5 mm2) ground

wire to the mounting location and strip each wire to the appropriate

length. The strip length is dependant on the wire nut or other

termination connector used (wire nuts are not provided).

2. Temporarily remove the sensor cover to gain access to the

configuration switches and mounting access holes. Hold the sensor in

one hand while gently twisting the cover clockwise.

3. Prepare the ceiling tile.

a. Align the flat side of the sensor to the finished side of the ceiling

tile and mark the access hole for wire pass-through.

b. Remove the ceiling tile material from marked access hole.

c. Pull the sensor wires through the access hole.

4. Insert the soft ceiling tile adapters through the provided pinholes in

the sensor mounting plate, one set located on each side of the sensor

near the mounting keyholes. Push the adapters through the ceiling

tiles, then bend each tine over in opposite directions for a secure fit on

the unfinished side of the ceiling tile.

5. Connect the EchoConnect wires from the sensor to the installed wires.

a. Connect the data - (typically black) EchoConnect wire from

sensor to the incoming EchoConnect (typically black) wire using a

WAGO wire termination connector.

b. Repeat the above step for the data + (typically white)

EchoConnect wire and for the ESD ground wire, using a new

WAGO connector for each termination type.

Dual Tech Ceiling-mount Vacancy Sensor Page 5 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Sensor Configuration

The Elaho Dual Tech Ceiling-mount Vacancy Sensor participates in an

Elaho control system using the configured Space and Address, which are

selectable using the rotary switches on the sensor electronics located behind

the removable cover.

DIPswitches, also located on the sensor electronics, set the sensor

functionality.

Note: The [MODE] and [AUX] buttons, and their related LEDs, are not

used and have no functionality on the Dual Tech Ceiling-mount Vacancy

Sensor.

DIP switches

Space and Address

switches

Set Space and Address

Two rotary switches on the controller provide for assignment of the sensor

Space and Address. By default, these switches are set to Space 1, Address 1.

Commands are shared by all devices within a given space.

1. Set the Space rotary switch to the desired number (1 through 16) for

the space you want the sensor to control.

2. Set the Address rotary switch to desired address (1 through 16) for the

sensor identification in the selected space.

Note: Do not duplicate a device Address within the same Space.

Dual Tech Ceiling-mount Vacancy Sensor Page 6 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

DIP Switch Settings

DIP switches on the sensor electronics provide for additional configuration

options including Use Custom Config, Vacancy Timeout, Enable/Disable

detection LEDs, PIR Only, and the ability to restore the sensor to its factory

defaults.

Switch # Use

1Unused

Enable/Disable Custom Config Mode

•

When “Custom Config” is set to Off (also known as Basic

configuration mode), local DIP switch settings for Vacancy

Timeout, Enable PIR LED, and dual technology features are

used. See

Configuration using Elaho Program Mode on

page1

•

When “Custom Config” is set to On, all other local DIP

switch settings are ignored. Instead, the settings made by

the EchoAccess Mobile App are used.

3 and 4

Vacancy Timeout

•

5 min = Switches 3 and 4 are Off

•

15 min = Switch 3 is Off and Switch 4 is On (default)

•

30 min = Switch 3 is On and Switch 4 is Off

•

Auto = Both switches are On

Detection LEDs

•

When set to On (default), the occupancy detection LEDs

illuminate when movement is detected.

•

When set to Off, the occupancy detection LEDs are

disabled unless the unit is in Walk Test mode.

PIR Only Mode

•

When set to On, acoustic detection technology is disabled

for the sensor.

•

When set to Off (default), both PIR and acoustic detection

technologies are used by the sensor.

7Unused

Restore to Defaults at boot

•

When set to On, then cycling power to the sensor, the unit

restores to its factory default settings.

•

Off is the default setting.

Dual Tech Ceiling-mount Vacancy Sensor Page 7 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Power Up and Test

Power Up

All EchoConnect terminations in the system must be made before applying

power to the system and sensor. When the sensor is powered up, the PIR and

acoustic detection LEDs illuminate for one minute for calibration and warm-

up, then return to normal operation according to the configuration.

Both the PIR and acoustic detection features of the sensor will automatically

adjust sensitivity threshold to eliminate nuisance tripping. During this time,

sensor configuration is not allowed and no events are triggered.

Dual Technology

When both PIR and acoustic detection are used, the following logic is used:

•

When the space is vacant, only manual control can switch the state to

occupied.

•

When the space is occupied, PIR, acoustic detection, and manual

control can reset the vacancy timeout.

•

When the vacancy timeout in the space has only been reset by acoustic

detection for 60 minutes, acoustic detection is disabled until the next

PIR detection event.

PIR (only) Detection

When acoustic detection is disabled (DIP switch 6 set to On), the following

logic is used:

•

When the space is vacant, only manual control can switch the state to

occupied.

•

When the space is occupied, PIR detection and manual control can

reset the vacancy timeout.

Basic Configuration

When the sensor is in Basic configuration mode (DIP switch 2 set to Off), the

sensor will activate a Space Off command when vacancy is detected.

Custom Configuration Mode

When functionality other than Space Off is required, place the sensor in

Custom configuration mode (DIP switch 2 set to On). Customization of the

sensor and all actions are configured using the ElahoAccess Mobile App.

For more detailed information about custom configuration options available

using ElahoAccess, see the ElahoAccess Mobile App integrated help system.

Dual Tech Ceiling-mount Vacancy Sensor Page 8 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Vacancy Timeout

Vacancy timeout is the amount of time the sensor waits to take action after

no movement is detected. By default, vacancy timeout is set to 15 minutes

(indicated by DIP switch 3 set to Off and 4 set to On; see

DIP Switch Settings

on page 7

). When the vacancy timeout ends, the grace period begins.

When the sensor detects vacancy, the vacancy timeout period begins. If the

sensor does not detect occupancy again during the vacancy timeout period,

the lights turn off and a 30 second grace period begins.

Grace Period

The sensor features a 30 second grace period after a vacancy timeout occurs.

During this grace period, if the sensor detects occupancy, it will turn on or

restore the previous lighting condition.

Auto Vacancy Timeout

The “Auto” vacancy timeout setting varies the vacancy timeout between

5 and 30 minutes depending on how often it identifies an occupancy trigger

after a vacancy timeout occurs (during the grace period).

Dual Tech Ceiling-mount Vacancy Sensor Page 9 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Ceiling-mount Vacancy Sensor

Walk Test

The sensor offers a Walk Test mode, which shortens the vacancy timer to ten

seconds and allows for simple and quick verification of the sensor’s coverage

and range in the installed space.

[Walk Test]

1. Prepare the site for configuration.

a. Make certain the sensor and lighting loads are powered and

connected for control by the Elaho control system.

b. You will need direct access to the sensor in order to place it into

Walk Test mode.

2. Press the [Walk Test] button on the bottom of the sensor to enable

the Walk Test feature. A green LED will flash, indicating Walk Test is

enabled and the vacancy timer will be shortened to ten seconds.

3. Move throughout the space including corners and areas that may be

obscured from line of sight to the sensor. Each time the sensor detects

movement, the lens illuminates red. If acoustic detection is enabled,

any sound detected will illuminate the lens green.

4. Adjust the lens masking, if installed, blocking certain areas of the

installed space from sensor detection. See

Lens Masking below

5. Walk Test mode automatically exits and the sensor returns to normal

operation after five minutes. You can also manually terminate by

pressing the [Walk Test] button again.

Lens Masking

Lens masks are provided in the packaging for your convenience. Use this to

block a section of the lens from detecting occupancy. To attach, cut to the

desired size, remove the backing and stick it on the sensor lens, covering the

desired sections.

Dual Tech Ceiling-mount Vacancy Sensor Page 10 of 12 Echoflex Solutions, Inc.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali echoflex Accessori

echoflex

echoflex MOS-17 Manuale utente

echoflex

echoflex Elaho Manuale utente

echoflex

echoflex RVS-A-xW Manuale utente

echoflex

echoflex FLS-41 Manuale utente

echoflex

echoflex Elaho Manuale utente

echoflex

echoflex TAP-21C Manuale utente

echoflex

echoflex RVS-A-xW Series Manuale utente

echoflex

echoflex TAP-31 Manuale utente

echoflex

echoflex ERUSB-C Manuale utente

echoflex

echoflex OWS Manuale utente

echoflex

echoflex RVS-A-XW Manuale utente

echoflex

echoflex TAP-17 Manuale utente

echoflex

echoflex MC-31 Manuale utente

echoflex

echoflex Elaho E-VAC-SR Manuale utente

echoflex

echoflex TAP-21 Series Manuale utente

echoflex

echoflex MOS-21 Series Manuale utente

echoflex

echoflex Elaho Dual Tech Wall-mount Vacancy Sensor Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

echoflex Elaho Dual Tech Ceiling-mount Vacancy Sensor Manuale utente

Manuali Accessori popolari di altre marche