Echowell a3 Manuale utente
EN 0
ENGLISH / ITALIANO / DEUTSCH / FRANÇAIS / ESPANÓL / NEDERLANDS
Congratulations on having chosen the cycle computer with altimeter functions from ECHOWELL. The easy operation of your new Echo-a3
will let you enjoy much fun from riding. Please read this manual carefully before using the device to get familiar with the operation logic.
The altitude calculation of this cycle computer works by measuring the atmospheric pressure. Since the weather is changing, the altitude
(converted from the air pressure measurement) for the same location may be variable at different times. However, if there's no rapid
weather change, the altitude differences caused by the weather are limited and can be generally accepted. Do not use this computer as a
specialized device for altitude measurement.
The altitude value shown in each Echo-a3 computer is pre-calibrated by the precise instrument at the factory before shipment. However, to
get accurate basis altitude, we suggest that you calibrate the current altitude data before each ride. And the calibration of altitude for your
Echo-a series is quite easy. (Refer to the content about button operation.) You may obtain the altitude information from topographic maps
or the Internet. If you are unaware of your basis altitude or do not care about the home altitude, you may reset the altitude to zero before
riding. In this way, the cyclist can still enjoy the fun of learning the accumulated altitude gains during the trip. The altitude data can be your
reference for riding over the same hills or mountains next time.
There is a highly sensitive pressure sensor inside each Echo-a3 cycle computer, and there is a hole at the bottom of each main unit for
measuring the pressure. You should always keep the hole clean to avoid incorrect measurement and must not poke a needle or any
pointed article into it to avoid damage. The atmospheric pressure measured by the sensor will be converted into current altitude. After using
your Echo-a3, you are sure to get a lot of fun from riding with it.
INTRODUCTION
EN 1
1. BUTTON OPERATION EN 2
2. DATA SETTING MODE EN 4
A-1. User data setting EN 5
A-2. Calendar data setting EN 5
A-3. Clock setting EN 6
A-4. Target Zone setting EN 6
A-5. EL ON/OFF setting EN 7
A-6. Bike1/Bike2 setting EN 7
A-7. Circumference data setting EN 7
A-8. ODO data setting EN 8
A-9. T.RT data setting EN 8
A-10. Alti Gain data setting EN 8
A-11. Alti Loss data setting EN 9
A-12. Calory data setting EN 9
A-13. LCD setting EN 9
3. SETTING SHORT CUT EN 10
4. FUNCTION GROUP MAP EN 11
INDEX
5. FUNCTION GROUP SEQUENCY EN 12
B-1. INST. Function EN 13
B-2. SPEED function EN 14
B-3. PULSE function EN 14
B-4. ALTI function EN 15
B-5. TEMP function EN 15
B-6. TOTAL function EN 16
6. FUNCTION DESCRIPTION EN 17
7. BACK-LIGHT MODE EN 21
Altitude Adjust mode EN 21
8. HOW TO START SPEED, AND HEART RATE
MEASUREMENT EN 22
9. SPECIFICATIONS EN 23
Wheel Cirucmference Measurement EN 25
Popular Tires Circumference Reference Table EN 25
10. BATTERY CHANGE EN 26
11. TROUBLE SHOOTING EN 27
12. PRECAUTIONS EN 28
EN 2
BUTTON
OPERATION
1. Data setting mode:
Abutton: Press for change or increase setting digital.
Hold 1's for auto increase.
Bbutton: Press for change setting digital.
Cbutton: Press for quit data setting mode.
Dbutton: No function.
Ebutton: Press for enter next data setting mode.
Data setting Process (ex. Circumference Setting)
Current
BPM
Curren
t
A
ltitude
Current
Speed
Function
Data
Function
Abutton Bbutton Cbutton Dbutton
Ebutton
OK!
EN 3
2. Operating mode:
Abutton: Press for change function Group.
Hold 3's for data reset. (see figure at right)
Bbutton: Press for change function mode.
Cbutton: Press for enter/quit data setting mode.
Dbutton: Press for select Bike1 or Bike2.
Ebutton: Press for turn on back-light 5's.
Abutton+Bbutton: Hold 3's for enter altitude adjust mode.
3. Altitude adjust mode:
Abutton: Press for change or increase adjust digital.
Bbutton: Press for change to next adjust digital.
Abutton +Bbutton: Press for quick reset data to zero.
Hold 3's for quit altitude adjust mode.
(20's auto quit altitude adjust mode without
Press any button).
BUTTON
OPERATION
A
button: Press for change function Group.
Hold 3's for data reset.
ex. [SPEED] →MAX SPD.
By pressing “YES”, you will reset (to zero)
the trip data in the following function groups:
SPEED, PULSE, ALTI, and RPM.
EN 4
INITIATE THE MAIN UNIT
ENTER DATA SETTING MODE
1. Hold the Abutton, Bbutton and Cbutton
simultaneously for 3 seconds to initiate the computer
and clear all data.
2. The LCD segments will be tested automatically after
the unit is initiated.
3. Press any Button to stop LCD test in order to set UNIT.
4. Press Abutton to choose”KG” or “Lb”.(pound)
5. Press Ebuton to begin USER DATA SETTING.
QUIT DATA SETTING MODE
It will automatically quit the data
setting mode after 20 seconds
without press any btton, or press
Cbutton.
ALL CLEAR:
Auto-running display
Press any button to enter
Data setting mode
Data settin
g
mode
UNIT SELECTION
A-1. USER DATA SETTING
DAT
A
SETTING MODE
EN 5
A-1. USER DATA SETTING
A-2. CALENDAR DATA SETTING
1. Press A button to change “MALE” or “FEMALE”.
2. Press B button to change the setting digit.
3. Press A button to increase the age by 1.
4. Press B button to change the setting digit.
5. Press A button to increase the weight by 1.
A
-2.
CALENDAR
DATA
SETTING
1. Press E button to begin CALENDAR DATA SETTING..
2. Press A button to increase the YEAR by 1.
3. Press B button to set MONTH.
4. Press A button to increase the MONTH by 1.
5. Press B button to set DAY.
6. Press A button to increase the DAY by 1.
A
-3.
CLOCK
SETTING
DATA SETTING MODE
EN 6
A-3. CLOCK SETTING
A-4. TARGET ZONE SETTING
1. Press E button to begin CLOCK SETTING.
2. Press A button to select 12H or 24H.
3. Press B button to set HOUR.
4. Press A button to increase the HOUR b
y
1.
5. Press B button to set MINUTE.
6. Press A button to increase the MINUTE by 1.
7. Press B button to set SECOND.
8. Press A button to reset the SECOND to 00.
A
-4.
TARGET ZONE
SETTING
1. Press E button to begin TARGET ZONE
SETTING.
2. Press A button to set UP target zone by
increasing 1 for pressing each time.
Target zone UP (upper limit) is within 45~240.
3. Press B button to set LO Target zone.
4. Press A button to set LO Target zone by
increasing 1 for pressing each time.
Target zone LO (lower limit) is within 40~199.
A
-5.
EL ON/OFF
SETTING
DATA SETTING MODE
EN 7
A-5. EL ON/OFF SETTING A-6. BIKE1/BIKE2
A-7. CIRCUMFERENCE DATA SETTING
1. Press E button to change EL ON/OFF SETTING.
2. Press A button to ON or OFF the EL. (also see page EN21).
1. Press A button to set Bike1 or Bike2..
2. Press E button to set circumference.
A
-6.
BIKE1/
BIKE2
SETTING
1. Press E button to begin CIRCUMFERENCE SETTING.
2. It shows the default value “c2155” (2155 mm). Measure
your wheel circumference and refer to the Wheel Size
Chart. (page. EN25)
3. Adjust the CIRCUMFERENCE value as instruction in
DATA SETTING processes (page EN 2).
A
-8.
ODO DATA
SETTING
DATA SETTING MODE
A
-7.
CIRCUMFERENCE
DATA SETTING
EN 8
A-8. ODO DATA SETTING (Odometer bike1/2)
A-9. T.RT DATA SETTING (Total riding time bike1/2) A-10. ALTI GAIN DATA SETTING (Total altitude gain bike1/2)
1. Press E button to begin ODO SETTING.
ODO Data setting range is 0~999999Km (Mile).
2. Adjust the ODO as instruction in
DATA SETTING processes.
A
-9.
T.RT DATA SETTING
1. Press E button to begin T.RT SETTING.
T.RT Data setting range is 0000h00m~9999h59m.
2. Adjust the T.RT as instruction in DATA SETTING
processes.
1. Press E button to begin ALTI GAIN SETTING.
ALTI GAIN Data setting range is 0~999999m (ft).
2. Adjust the ALTI GAIN as instruction in DATA SETTING
processes.
A
-10.
A
LTI GAIN
DATA
SETTING
A
-11.
A
LTI LOSS
DATA
SETTING
DATA SETTING MODE
EN 9
A-11. ALTI LOSS DATA SETTING (Total altitude loss bike1/2) A-12. CALORY DATA SETTING (Calory consumption bike1/2)
A-13. LCD DATA SETTING (LCD Brightness setting)
1. Press E button to begin ALTI LOSS SETTING.
ALTI LOSS Data setting range is 0~999999 m (ft).
2. Adjust the ALTI LOSS as instruction in DATA SETTING
processes.
1. Press E button to begin CALORY SETTING.
CALORY Data setting range is 0~999999kcal.
2. Adjust the CALORY as instruction in DATA SETTING
processes.
A
-12.
CALORY
SETTING
1. Press E button to begin LCD SETTING.
2. Press A button to select level L1, L2, L3 or L4.
A
-1.
USER DATA
SETTING
A
-13.
LCD
SETTING
DATA SETTING MODE
Indice
Altri manuali Echowell Accessori per biciclette
