Ecleris MICROSTAR Series Manuale utente

USER MANUAL

MICROSTAR SERIE OM-200

MICROSCOPE

INFORMATION ABOUT THIS MANUAL

Version: 2023.01

Year: 2023

Language: English

All the rights to this manual are reserved, especially reproduction, publication and translation rights. No portion of this manual may be

reproduced by no means (photocopy, microfilm or other methods) without previous written authorization from ECLERIS. Neither can it

be reproduced, multiplied or published through any electronic data processing form.

The information contained in this manual may be modified or broaden without previous notification, without it representing any

responsibility to ECLERIS.

ECLERIS USA

11801 NW 100th Rd

Suite 17

Medley, FL 33178, U.S.A.

Phone: +1 786 483 7490

CMC Medical Devices & Drugs S.L.

C/ Horacio Lengo Nº18, CP29006,

Málaga, Spain

Ph. +34951214054

Email: [email protected]

USER MANUAL / MANUAL DE USUARIO –MICROSTAR 
 
Page 2of 64 
INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US 
TABLE OF CONTENT 
SYMBOLS................................................................................................................................4 
SAFETY INFORMATION.........................................................................................................5 
1 WARNINGS..........................................................................................................................5 
DESCRIPTION.........................................................................................................................6 
1 INTENDED USE...................................................................................................................6 
2 INTENDED USER................................................................................................................6 
3 DESCRIPTION AND COMPONENTS..................................................................................6 
3.1 FLOOR STAND MICROSCOPE (OM-200F)..................................................................7 
3.2 OPTICAL HEAD............................................................................................................8 
INSTALLATION AND OPERATION .........................................................................................9 
1 BASE INSTALLATION..........................................................................................................9 
2 COLUMN INSTALLATION..................................................................................................10 
3 FOREARM-COLUMN INSTALLATION...............................................................................11 
4 OPTICAL HEAD-ARM INSTALLATION..............................................................................12 
5 BINOCULAR-SPLITTER INSTALLATION ..........................................................................13 
6 VIDEO CABLES INSTALLATION.......................................................................................15 
OPERATION - FUNCTIONS..................................................................................................16 
1 MICROSCOPE OPERATION.............................................................................................16 
2 CONNECTIONS.................................................................................................................17 
2.1 FOREARM ..................................................................................................................17 
2.2 ARM............................................................................................................................17 
3 LIGHT SOURCE.................................................................................................................18 
4 INTERPUPILLARY DISTANCE ADJUSTMENT..................................................................18 
5 DIOPTRIC CORRECTION ADJUSTMENT.........................................................................18 
6 MAGNIFICATION VARIATION...........................................................................................19 
7 COLOR FILTER SELECTOR .............................................................................................19 
8 DIAPHRAGM SELECTOR..................................................................................................19 
MOVEMENT AND SHIPPING................................................................................................19 
1 FOREARM MOVEMENT....................................................................................................20 
2 PANTOGRAPHIC ARM MOVEMENT.................................................................................20 
3 ROTATIONAL MOVEMENT OF THE OPTICAL HEAD ......................................................21 
4 OPTICAL HEAD ROTATION AXIS.....................................................................................22 
5 OPTICAL HEAD TILT.........................................................................................................22 
6 MICROSCOPE SHIPMENT................................................................................................23 
7 MOUNTING THE MONITOR HOLDER...............................................................................23 
MAINTENANCE.....................................................................................................................26 
1 CLEANING.........................................................................................................................26 

USER MANUAL / MANUAL DE USUARIO –MICROSTAR 
 
Page 3of 64 
INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US 
1.1 CLEANING THE EXTERNAL SURFACES..................................................................26 
1.2 DISINFECTION...........................................................................................................26 
1.3 CLEANING OF OBJECTIVE LENS AND EYEPIECES................................................26 
2 ELECTRICAL CONNECTIONS..........................................................................................27 
3 FUSE CHANGE..................................................................................................................27 
TECHNICAL SPECIFICATIONS............................................................................................28 
TROUBLESHOOTING...........................................................................................................31 
TECHNICAL SERVICE.......................................................................................................32 
WARRANTY.......................................................................................................................32 
 
 
 

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 4of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

1. SYMBOLS

Warning

EU Authorized

Representative

Caution

CE Mark

Read the related documentation

This side up

Alternate current

Fuse

Protective earth (Ground)

Video output

Equipotential bonding

Freeze image function

Manufacturer identification

(Name, Address)

Video camera

Serial number

White balance function

Manufacturing date (MM/AAAA)

Lightning

Do not discard with the

household waste

Iris diaphragm

Light intensity

Temperature limits

Optical filter

Pressure limits

Fragile

Humidity limits

On/off integrated light

Keep away from rain

Decrease light intensity

Increase light intensity

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 5of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

2. SAFETY INFORMATION

This manual is intended to explain the installation and functioning of the device.

Warnings: This symbol shall be used in the manual to indicate situations of neglect which

could cause injuries or material considerable damage.

Cautions: This symbol shall be used in the manual to indicate information about

important cautions to prevent undesired consequences.

Read this manual carefully before using the device.

Should you have any doubt regarding the contents of the manual herein, or the operation and

safety of the device, contact your local distributor or the nearest ECLERIS office.

2.1 WARNINGS

It is important to read this manual carefully before using the Microstar Microscope.

ECLERIS will not be held responsible for damage that can occur to the device due to not

following the instructions or not observing the following criteria:

To avoid risk of electric shock, this device must only be connected to an earth-protected

power supply.

Do not install the equipment next to heat sources, such as heaters.

The Microscope must be used in medical facilities with a proper electrical installation,

including a grounding in compliance with the regulations.

The microscope should be connected to the mains through the supplied cord or a

replacement with the same certifications.

The mains should be grounded with no adapter needed.

The sectioning of the electrical network is carried out by disconnecting the power cable, or

by removing the connector from the electrical outlet.

The device is connected to a ground protection through a ground conductor in the power

supply cable. This ground connection is essential for the safe use of the equipment

The device is provided with a connectable power cable that assures proper electrical

isolation. If it needs to be replaced, it should have the same features than the original.

Only connect the device to visualization devices that meet the IEC 60601-1 standard.

Device not appropriate to be used near or around flammable anesthetic gas mixture with air,

oxygen or nitrous oxide.

Do not look directly into the light output; the optical head has a very bright light output.

To move the microscope (during installation and intended use) verify light is off, in order to

avoid bright light on the face.

Do not insert objects into the holes. Do not place any container with liquids on top of the

device.

In case of interference with other electro-medical or electric equipment, it is recommended

increasing the distance between the device and the other equipment to minimize these

effects.

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 6of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

Do not open the device. Maintenance and repairs must be done by ECLERIS or an

authorized company by the fabricant. ECLERIS will not be responsible for the

consequences of repairs or maintenance carried out by unauthorized personnel.

This instruction manual must be kept together with the equipment for future reference. In

case the device is sold or donated, this manual must be enclosed.

If by any of the following:

Inadequate use of the equipment.

Failure to use the instruction manual.

Bad maintenance and care of the equipment.

Repair or manipulation by unauthorized personal.

…personal or material damage is produced to a third party, ECLERIS, the manufacturer and

sales agent of this equipment, will not assume responsibility for said damage.

The device and its accessories should never be discarded with the household

waste. Please check local regulations for electronic components disposal or recycle

of electrical and electronic device.

3. DESCRIPTION

3.1 INTENDED USE

The microscope has been designed to perform observation in diagnostic and surgical procedures.

It is used in different medical specialties, as well as in dentistry, where a magnification of the

working field is necessary to ensure the success of the treatment.

3.2 INTENDED USER

The intended users of this device are physicians or other health professionals, with experience or

training in the use of microscopes.

3.3 DESCRIPTION AND COMPONENTS

The Ecleris Microstar OM-200 Microscope and its accessories allow this equipment to meet all

the necessary characteristics for the different specialties.

This user manual describes the recommended procedures in order to install and use the Ecleris

Microstar OM-200 Microscope. The user manual contains all the information about care and

properly handling of the microscope.

Read the manual thoroughly before operating the equipment.

The accessories of the Ecleris Microstar OM-20 Microscope are the following:

Monitor holder

Splitter

Special cable containing 1 male HDMI plug to connect to the video system, and 2 DC-

PLUG to power the splitter and the integrated light.

The device has different versions:

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 7of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

Code

Description

Binocular rotation

Pantographic arm

length

OM-200F

Floor-stand

Straight

23.03” (585mm)

45º Inclined

32,09” (815mm)

180° Inclinable

3.3.1 FLOOR STAND MICROSCOPE (OM-200F)

Components:

1. Optical Head

2. HD beam Splitter

3. Binocular

4. Tension knob

5. Progressive brake

6. Lock brake

7. Pantographic arm

compensator

8. Switch on/off

9. Forearm

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 8of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

10. Progressive brake

11. Progressive brake 12. Column

13. Microscope Base

3.3.2 OPTICAL HEAD

1. Magnification selector

2. Micro focus adjustment

3. Light filter selector

4. Diaphragm selector

5. Light on/off

6. Light intensity (increase)

7. Light intensity (decrease)

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 9of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

4. INSTALLATION AND OPERATION

4.1 BASE INSTALLATION

To assemble the microscope base, 4 wheels and 4 counterweights must be fitted.

The wheels are assembled by screwing the bolt into the ends of the base as indicated in the

following figure.

A wrench should be used to tighten the wheel bolts solidly to the base of the microscope.

The base has 4 removable weights that allow the easy handling of the microscope with a reduced

weight of the base.

Once the wheels have been mounted, the 4 removable weights must be placed.

Once the weights have been mounted, the plastic base cover must be placed on the base, as

indicated in the following figure:

USER MANUAL / MANUAL DE USUARIO –MICROSTAR

Page 10 of 64

INMANUUML019 USER MANUAL - M. USO OM-200 V.2023.01 ENG-ESP US

4.2 COLUMN INSTALLATION

Once the wheels and the base cover are placed, the column must be mounted on the base.

Put the column in the central axis of the base as indicated in the following figure:

Tighten the set screw with an Allen wrench.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Ecleris Microscopio

Ecleris

Ecleris MICROSTAR OM-100 Manuale utente

Ecleris

Ecleris MICROSTAR OM-100 Manuale utente

Manuali Microscopio popolari di altre marche

Thermo Scientific

Thermo Scientific Nicolet iN10 Guida

National

National DC3-163 Manuale utente

KERN Optics

KERN Optics OPE-1 Manuale utente

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuale utente

Prior

Prior Lux POL Manuale utente

Opitec

Opitec Smartscoop 115615 Manuale utente

KERN

KERN OPO-1 Manuale utente

Topcon

Topcon SP-1P Manuale utente

Motic

Motic PA43 Manuale utente

Leica

Leica DVM5000 Guida utente

MshOt

MshOt MZ62 Manuale utente

KERN Optics

KERN Optics OZR-5 Manuale utente

VWR

VWR VisiScope 384 Series Manuale utente

Nikon

Nikon ECLIPSE E200 POL Manuale utente

Leica

Leica DI C800 Manuale

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

Olympus

Olympus SZ61 Manuale utente