eCopy ScanStand Manuale utente
© eCopy, Inc. All trademarks are properties of their respective owners (see product documentation for details). P/N: 73-00030 (2/2006)
eCopy ScanStandTM
Assembly Instructions
Revision 2.1
Licensing, Copyright, and Trademark Information
The information in this document is subject to change and does not represent a commitment on the part of eCopy, Inc. The
software described in this document is furnished under a license agreement. The software may be used or copied only in
accordance with the terms of the agreement. It is against the law to copy the software on any medium except as specified in
the license agreement. No part of this document may be reproduced, transmitted in any form or by any means, electronic or
mechanical, including photocopying, recording, or information storage and retrieval systems, or translated into any language
for any purpose other than the purchaser’s personal use, without the written permission of eCopy, Inc.
© 1992- 2005 eCopy, Inc.
eCopy, the eCopy logo, eCopyFax, the Simplify logo, the MailRoom logo, eCopy ShareScan OP, eCopy ScanStation, eCopy
ScanStation OP, eCopy Desktop, eCopy Quick Connect, eCopy Xpert Compression, UniDoc, SpeedFax, and SpeedPrint are
trademarks of eCopy, Inc. ShareScan, Simplify, and MailRoom are registered trademarks of eCopy, Inc.
All other terms and products are trademarks or registered trademarks of their respective owners and are hereby
acknowledged.
eCopy ScanStand Assembly Instructions 1
Planning the installation
You can assemble the eCopy ScanStand in several configurations. Determine the best configuration so the arm,
touch screen, and keyboard do not interfere with copier access. In most situations:
> If the finisher is on the left of the copier, configure the PC and arm at the right of the assembly.
> If the finisher is on the right of the copier, configure the PC and arm at the left of the assembly.
> Leave 6-9 inches (15-23 cm) of clearance between the ScanStation and the copier access door.
Variations to these standard configurations are possible to accommodate paper reservoirs or other accessories
(see next page).
You can also place the PC behind the copier, as shown below.
Typical configuration for finisher on left Typical configuration for finisher on right
Configuration if PC is placed behind and left of copier Configuration if PC is placed behind and right of copier
2eCopy ScanStand Assembly Instructions
Alternative arm positions
You can position the arm support post on any one of the three vertical struts on the rear frame. For example, if a
paper reservoir is present at the side of the copier, you can position the post on the middle vertical strut so the
screen and keyboard are closer to the copier's control panel.
In rare situations, you may need to position the post and arm assembly at the opposite end of the rear frame
from the angle frame. The diagrams below illustrate various configuration options.
Typical configuration Configuration to accommodate
reservoir or other large accessory
Rarely used but available if
required
Right
configuration
Left
configuration
eCopy ScanStand Assembly Instructions 3
Component identification
A: Touch screen B: Keyboard C: Arm D: Rear frame E: Arm support post
F: PC cover G: L-bracket H: PC clamp I: Master fastener kit J: Angle frame
Note
Angle frame (J)
ships inside PC
cover (F)
4eCopy ScanStand Assembly Instructions
(Phillips screwdriver not included)
Technical support
US/North America
Technical Support hours are Monday through Friday, 6:00 A.M. to 5:30 P.M. EST.
Phone: +1 (603) 881-4450 (select option 8)
E-mail: support@ecopy.com
Outside North America
Please contact your local dealer or national sales organization.
The Master Fastener Kit contains four smaller kits.
Do not open the smaller kits until you are ready to use them.
Each kit is used in a separate step in the assembly process.
eCopy ScanStand Assembly Instructions 5
Fastener Kit #1: P/N 16-5001-A
Components shown full size to help identification
1.1 Screw feet into threaded holes in underside of
rear frame (2) and angle frame (1). Screw feet in
all the way.
Feet (3)
Step 1: Rear and angle frame assembly
6eCopy ScanStand Assembly Instructions
1.2 Position angle frame at left or right of rear
frame as appropriate. The angle frame is
typically placed on the opposite side of the
copier from the finisher.
Left configuration (front view)
Right configuration (front view)
1.3 Put a washer on each 50 mm (2 inch) hex bolt
and insert bolts through non-threaded holes in
back of frame and into threaded holes in angle
frame.
Left configuration (rear view)
Right configuration (rear view)
1.4 Tighten bolts securely using 13 mm wrench. Do
not over tighten or you will bend the metal
tubing.
Rear and angle frame assembly (continued)
eCopy ScanStand Assembly Instructions 7
Fastener Kit #2: P/N 16-5001-B
Components shown full size to help identification
2.1 Examine rear of copier and determine which of
the vertical struts to use for the L bracket.
Position bracket to avoid contact with vents or
cable connectors.
2.2 Put a washer on each 45 mm (1-3/4 inch) hex
bolt.
2.3 From back of frame, insert bolts through top
and bottom holes in selected strut.
2.4 Place L-bracket on bolts and attach loosely using
hex nuts.
2.5 Slide bracket to lowest position. You will re-
position and tighten the L-bracket later.
Before you attach the L-bracket,
determine which vertical strut you will
use for the arm support post and attach
the L-bracket to an unused strut.
Left configuration with optional L-bracket position
Vertical struts
Step 2: L-bracket attachment
8eCopy ScanStand Assembly Instructions
Fastener Kit #3: P/N 16-5001-C
Components shown full size to help identification
3.1 Insert bolts through strut from back of frame.
3.2 Place washer and nut on each bolt. Turn only 2-
3 times leaving bolt heads extended at least 16
mm (5/8 inch) from rear of frame.
Note bolt head alignment and required gap
3.3 Slide arm support post over bolt heads, flat side
against rear frame, fitting the two bolt heads
into the T-slot on the post.
Tip: While holding post with one hand, rotate bolt
heads to align edges parallel to T-slot.
3.4 Position post at desired height. Typically, the
bottom of the post is aligned with the top edge
of the rear frame's lower cross-member.
3.5 Tighten nuts securely using 13 mm wrench.
Frame
Bottom of arm
support post
Step 3: Arm support post attachment
You can mount the arm support post on any one of the available vertical struts on the rear frame (see
Indice
