ECRM Mako 4 CTP Manuale
AG45134 Rev. 2
Mako 4 CTP
Operator Guide
AG45134 Rev. 2
Mako 4 CTP
Operator Guide
This guide reflects the Mako 4 CTP system as of April 2003.
© copyright ECRM Incorporated 2003
Additional copies of this guide may be obtained by writing or calling:
ECRM Order Processing
554 Clark Road
Tewksbury, MA 01876
Phone No. (US) - (+1) 978-851-0207 — Fax (US) - (+1) 978-851-7016
Phone No. (UK) - (+44) 1923-218255 — Fax (UK) (+44) 1923-218256
Phone No. (Hong Kong) - (+852) 2-564-8989— Fax (Hong Kong) (+852) 2-564-8821
Visit our Web site: www.ecrm.com
Proprietary Notice
The information contained in this publication is the sole property of ECRM. It cannot be
reproduced, in whole or in part, without the express written consent of ECRM. The information
is believed to be accurate as of the publication date, but it is subject to change without notice due
to continuing product development.
ECRM® and Mako® are trademarks of ECRM Imaging Systems. Other brand and product
names are trademarks or registered trademarks of their respective owners.
AG45134 Rev. 2 iii
Table of Contents
Chapter Page Number
Chapter 1: Requirements and Safety.........................................................1-1
Introduction to the System ................................................................1-1
System Requirements .......................................................................1-1
Laser Safety ......................................................................................1-2
Regulatory Information .....................................................................1-2
Chapter 2: System Operation.....................................................................2-1
Introduction .......................................................................................2-1
Parts of the System ...........................................................................2-1
Starting Up the System .....................................................................2-3
Shutting Down the System ...............................................................2-4
Using the Control Panel ....................................................................2-4
System Menu Options .......................................................................2-5
Menu selection .................................................................................2-6
User Preferences Menu .....................................................................2-6
User Maintenance Menu ...................................................................2-9
Test Patterns Menu ...........................................................................2-10
Status Messages ................................................................................2-13
Error Messages .................................................................................2-14
Chapter 3: Media Handling........................................................................3-1
Introduction .......................................................................................3-1
Installing and Removing the Pin Bar ................................................3-3
Loading Media ..................................................................................3-6
Chapter 4: Maintenance and Troubleshooting.........................................4-1
Introduction .......................................................................................4-1
General Maintenance ........................................................................4-1
Clearing Misfeeds .............................................................................4-5
Using the User Maintenance Menu ..................................................4-7
Leveling the System ..........................................................................4-8
iv AG45134 Rev. 2
AG45134 Rev. 2 v
List of Figures
Figure Name Page Number
Media Sensitivity Label.........................................................1-2
Identification and Certification Label....................................1-3
External View of the System.................................................2-1
Control Panel .........................................................................2-2
Pinch Rollers..........................................................................2-3
Control Panel .........................................................................2-4
User Preferences Menu Map..................................................2-7
User Maintenance Menu Map................................................2-9
Test Patterns Menu Map........................................................2-11
Media Orientation.................................................................3-1
Pin Bar Location...................................................................3-3
Pin Bar ..................................................................................3-4
Alignment Pin Hook..............................................................3-4
Setting the Alignment Pin in the Hook..................................3-5
External View of the System.................................................3-7
Loading Edge-registered Plates .............................................3-8
Loading Notch-registered Plates............................................3-10
System Details .......................................................................4-1
Fan Filter Removal ................................................................4-2
Media Transport.....................................................................4-4
Internal Registration Pin........................................................4-5
Plate Positions over the Registration Pin...............................4-6
User Maintenance Menu Map................................................4-7
Levelling Feet Location.........................................................4-8
vi AG45134 Rev. 2
AG45134 Rev. 2 vii
Preface
Scope of this Guide
This guide provides instructions for the operating and maintaining a Mako 4 CTP
platesetter. This guide describes all aspects of the operation of the system, from the
loading of media, to the delivery of exposed media to an on-line processor.
The Mako 4 CTP employs a Class 3B laser. This guide contains important safety
information and regulatory information about the laser.You should read this
information thoroughly before operating the system or performing the procedures
described in this guide.
This guide assumes that the system is already properly installed and plugged into
the AC mains. Further, this manual assumes that the system has been calibrated
and tested for proper operation and acceptable output. Only procedures necessary
for safe and efficient operation are provided in this manual.
Organization of this Guide
Chapter 1: Requirements and Safety
Chapter 1 includes system operating requirements and information about laser
safety.
Chapter 2: System Operation
Chapter 2 discusses all operational features and provides complete listings of
system operational messages. All of the system menus are described in detail. All
of the menu items are mapped in flow diagrams.
Chapter 3: Media Handling
Chapter 3 provides instructional information on how to load media. Guidelines for
handling media are also provided.
Chapter 4: General Maintenance andTroubleshooting
Chapter 5 covers general maintenance items that can be performed by the operator.
This chapter includes troubleshooting tips and a procedure for re-locating or
moving the system.
viii AG45134 Rev. 2
Not Covered in this Guide
Engineering Specifications
Alignment and Calibration
Detailed Field Service Information
Terms and Conventions Used in this Guide
Type This term is an instruction to type data at the keyboard.
Italic
typeface Used to indicate the first mention of an important concept.
Bold
typeface Used to highlight important details in text or illustrations and
to indicate user actions.
Bold sans-serif
typeface Used to represent file names or menu options to be selected.
Also refers to section names.
Note
: Blocks of text used to advise of related information.
IMPORTANT
Notices used to emphasize very important information.
AG45134 Rev. 2 1-1
1
Requirements
and Safety
Introduction to the System
The Mako 4 CTP produces plates for use in the printing industry. Plates are
manually loaded by positioning the plate in the pin registration system and closing
the pinch rollers. Imaging of the plate is then started with the push of a button.
When the imaging is complete, the exposed plate automatically passes out of the
platesetter and onto the media transport, which feeds the plate into a customer-
supplied plate processor .
All operations (plate loading, imaging, and transport to the processor) must be
performed in a safe-light environment. Refer to your plate manufacturer’s
specifications for safe-light requirements.
System Requirements
System Power and Heat Dissipation
Power
90 - 264 Volts; 3 Amps; 250 Watt maximum;
50/60Hz, single phase.
Heat Dissipation
850 BTU/hour
Environmental Requirements
Temperature
- 70 - 77 degrees F (21 - 25 degrees C)
Humidity
45 - 65%, non-condensing.
Note: Operating the system outside of the ranges specified above may affect
performance.
1-2 AG45134 Rev. 2
Laser Safety
Laser Product Classification
The system is classified as a Class one (I) laser product which contains a Class 3B
(IIIb) laser System. This classification means that the operator is exposed to no
hazardous laser light during operation and maintenance. The laser itself, however,
is a Class 3B (IIIb) laser device, and emits visible laser light which is considered
hazardous by FDA published limits.
IMPORTANTWARNING
se of controls or adjustments or performance of
procedures other than those specified in this guide
may result in hazardous laser light exposure.
System LaserWavelength Identification Label
The system contains a laser that emits visible laser light. The identification label is
located on the output side of the machine, above the output rollers. The label is
shown in Figure 1-1.
Figure 1-1 Media Sensitivity Label
Regulatory Information
Electromagnetic Emissions
DOC - Canada
The Canadian Department of Communications requires compliance with the Radio
Interference Regulations, ICES -003.
This digital apparatus does not exceed the ClassA limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
EMC Directive - Europe
Complies with EN 55011: 1998
This is a Class A product. In a domestic environment this product may cause radio
MEDIA SENSITIVITY
405 nm VISIBLE
Altri manuali per Mako 4 CTP
1
Indice
Altri manuali ECRM Stampante tutto in uno
Manuali Stampante tutto in uno popolari di altre marche
Triumph Adler
Triumph Adler DC 2016 Manuale
Epson
Epson WorkForce WF-2510 Guida utente
Epson
Epson Stylus Scan 2000 Manuale di installazione e funzionamento
Epson
Epson PictureMate Snap PM 240 Manuale di istruzioni
Konica Minolta
Konica Minolta bizhub C35 Manuale utente
Brother
Brother MFC-J430w Manuale utente
