Eddylight DS-1404A Manuale utente

GOBO LED Light

DS-1404A

USER MANUAL!

2

1. Introduction

Thank you for purchasing our GOBO LED light. Please read these

instructions carefully before operating to avoid any possible damage and

accidents caused by misuse.

The GOBO LED light has a hydrodynamic aluminum shell. One 10W white

LED is used to create a bright light output. It draws low power and is low

weight.

Packing List

-LED GOBO Light

-User manual

-Power cord

2. Safety Information

-Please consult skilled service technicians for any repairs required

-Always disconnect from the power source before setting up, moving and

servicing

-Avoid direct eye contact to the light when in operation

-Make sure the power supply voltage is compatible with this light

-Before installation, please check the light’s fasteners and mechanical

structure is in good condition and not damaged

-The light is designed for indoor use, below 40 degrees celsius

-The ﬁxture may be mounted in any position provided there is adequate

room for ventilation. Make sure there are no ﬂammable and explosive

items within 0.5 meters.

-Please ensure the ground is always connected

3

3. Dimensions and Speciﬁcations

Voltage: AC100V/264 VAC

Frequency: 47-63 Hz

Power Consumption: 25 W

Lamp: 10W white LED

Beam Angle: 13 degrees

Net Weight: 2 Kg

IP Rating: IP20

Dimensions:



www.EddyLight.com 1-800-914-3538

4

4. GOBO Installation

Unscrew the 2 knobs on the

top of the projector and

remove the piece from inside

Place the GOBO in the center

hole. Squeeze the ring and

place it on top of the GOBO

to ensure the GOBO stays in

place.

After the GOBO is placed in the

correct orientation, place the GOBO

holder back into the projector and

screw it on.

5

5. Operation

The easiest way to operate your projector is through the remote control.

You can also use the buttons on the projector to go through the options.

All of the options are set using a scale of 0-255. To set it to the number

you desire, move UP or DOWN to that number and press ENTER. The

light will turn off, then press ENTER again.

R- Red light intensity (0 off, 1 dimmest, 255 brightest)

G- Green light intensity (0 off, 1 dimmest, 255 brightest)

B- Blue light intensity (0 off, 1 dimmest, 255 brightest)

W- White light intensity (0 off, 1 dimmest, 255 brightest)

SHUT - Strobe effect.

0 = no strobe effect.

1-255 different strobe pattern and speed

GOBO - Rotation feature.

000 = off

1-100 = different positions

101-170 = different speeds of counterclockwise rotation

185 - 250 = different speeds of clockwise rotation

NOTE: R, G, B options are only for color projector. You can mix different values of red,

green and blue to create any color.

www.EddyLight.com 1-800-914-3538

0 0

MENU UP DOWN ENTER

MADE IN CHINA

RoHS

To focus the projector, rotate the

lens. Every time you adjust the

distance of the projector to the

projection surface, you will need

to adjust the focus

Focus

6

6. DMX Control Function

3CH

5CH

VALUE

FUNCTION

CH1

0-255

Intensity

CH2

0-5

No strobe

6-20

Random burst strobe(slow to fast)

21-60

Normal strobe(slow to fast)

61-100

Electronic Sinewave(slow to fast)

101-140

Random Strobe(slow to fast)

141-180

Opening pulse(slow to fast)

181-220

Closing pulse(slow to fast)

221-255

Electronic Squarewave(slow to fast)

CH3

0-100

0-360°

101-170

CW(slow to fast)

171-180

Stop

181-250

CCW(slow to fast)

251-255

Stop

CH4

0-70

No effect

71-75

AUTO 1(W + GOBO CW)

76-80

AUTO 2(W↑,W↓+ GOBO CW)

81-85

AUTO 3(W + GOBO CCW)

86-90

CHASE 1

91-95

CHASE 2

96-100

CHASE 3

101-255

Reserved

CH5

0-10

Use the dimmer mode which menu has set up

11-20

Dimmer off

21-30

Dimmer 1

31-40

Dimmer 2

41-50

Dimmer 3

51-60

Dimmer 4

61-254

Use the dimmer mode which menu has set up

7

7. Display Operation Instruction

Instructions：

Master mode sends a DMX signal to all other LED light units connected

via DMX."

Slave mode receives the incoming DMX signal from the Master, using the

values set by the Master unit.This allows for a large group of lights to be

connected and controlled by only one light.

For Master mode, press ENTER on the unit to display “*” on the LED

display.

When there is no"“*” being displayed on the LED display, the light is set to

Slave"by default.

access the menu or return to a previous menu option

ENTER

select the current menu option

menu selection or parameter increments

DOWN

menu selection or parameters decrease

www.EddyLight.com 1-800-914-3538

8

Tab

Level 1

Level 2

Level 3

Level 4

ADDR(Address)

001-512

STAT(Static

control)

0-255*

SHUT

0-255*

GOBO

0-255*

SET(Set)

CHMD(Channe

l mode)

5CH

3CH

DIM(Dimming

mode)

OFF

DIM1

DIM2

DIM3

DIM4

DISY(Display

set)

ON(Perma

nent on)

2MIN (2

minutes off)

CALP(Calibrate

position)

0-255

AUTO(Auto)

AT01

RUN..*

AT02

RUN..*

AT03

RUN..*

CHS1

RUN..*

CHS2

RUN..*

CHS3

RUN..*

PROG（Program）

CHS1（Chase

1）

SC01（Sce

ne 1）

0-255

SHUT

0-255

GOBO

0-255

TIME

0-255(S)

WAIT

0-25.5(S)

USE

YES/NO

SC20（Sce

ne 20）

CHS3（Chase

3）

INFO（Information

）

SOFT(Software

version)

Vx.x

POW(Power

reduction)

100%/80%/

50%

LOAD(Load)

ST L（Setting

load)

YES/NO

L（Program

load)

YES/NO

SEND(Send)

YES/NO

9

6.1 DMX Address Setting

1. Select the ADDR Menu by navigating to it and pressing ENTER.

2. Press the UP/DOWN buttons to navigate between channels 1 - 512.

3. Press ENTER to select your desired channel.

6.2 Static Setting

1. Select the STAT menu by navigating to it and pressing ENTER

2. Press the UP/DOWN buttons to select WHITE, SHUT, or GOBO.

3. Press the UP/DOWN buttons to set up the【0-255】numerical value.

4. Press the ENTER button to escape and save.

6.3 Channel Mode Setting

1. Select the SET menu by navigating to it and pressing ENTER

2. Select the CHMD menu by pressing ENTER

3. Press the UP/DOWN buttons to select 3CH or 5CH

4. Press the ENTER button to escape and save.

6.4 Dimming Mode Setting

1. Select the SET menu by navigating to it and pressing ENTER

2. Select the DIM menu by pressing ENTER

3. Press the UP/DOWN buttons to select OFF, DIM1, DIM2, DIM, 3 or

DIM4

4. Press the ENTER button to escape and save.

When off is selected there will be no delay dimming effect

DIM1 is the slowest. DIM4 is the fastest.

www.EddyLight.com 1-800-914-3538

10

6.5 Display Setting

1. Select the SET menu by navigating to it and pressing ENTER

2. Select the DISY menu by pressing ENTER

3. Press the UP/DOWN buttons to select ON, 2MIN.

4. Press the ENTER button to escape and save.

6.6 Calibrating the GOBO to Original Position

1. Select the SET menu by navigating to it and pressing ENTER

2. Select the CALP menu by pressing ENTER

3. Press the UP/DOWN buttons to set up the 0-255 numerical value.

4. Press the ENTER button to escape and save.

6.7 Auto Run, Self-Program

1. Select the AUTO menu by navigating to it and pressing ENTER

2. Press the UP/DOWN buttons to select AT01, AT02,AT03, CHS1,

CHS2, CHS3

3. Press the ENTER button to escape and save.

Indice

Altri manuali Eddylight Attrezzatura di illuminazione

Eddylight

Eddylight Economy Manuale utente

Eddylight

Eddylight DSY-LED252-IP65-RGB Manuale utente

Eddylight

Eddylight EDD-GL-183 Manuale utente

Eddylight

Eddylight EDD-RP-WBIF1006 Manuale utente

Eddylight

Eddylight LED PAR 64 Manuale utente

Eddylight

Eddylight LED GOBO Manuale utente

Eddylight

Eddylight EDD-VP-S120 Manuale utente

Eddylight

Eddylight 4 in 1 RGBW SlimPar LED Q18 Manuale utente

Eddylight

Eddylight DSY-LED252-IP65-RGB Manuale utente

Eddylight

Eddylight DSY-LED252-IP65-RGB Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente