Edelbrock 68452 Manuale utente
©2006 Edelbrock Corporation
Rev. 5/06 - DA/mc Catalog #68452, #68453
Brochure #63-68452
Page 1 of 2
SHORTY HEADER
for 1986-1993 Ford Mustang, Capri, Mark,
5.0L (302 V8) with E.F.I., Auto & Standard Transmission
Catalog #68452, #68453
INSTALLATION INSTRUCTIONS
PLEASE study these instructions carefully before installing your new Shorty Header. If you have any questions, please call
our Technical Hotline at: 1-800-416-8628 from 7:00 am - 5:00 pm, Monday-Friday, Pacific Standard Time or e-mail
HEADERS: These components are designed to improve the exhaust efficiency of the Ford 5.0 Litre V8 engine with E.F.I.
(Electronic Fuel Injection). These tubular manifolds are a direct replacement for the factory exhaust manifolds. A
performance gain can be expected by the installation of this system. This system does not require welding for installation
and retains all O.E.M. emissions equipment.
SUGGESTED TOOLS FOR INSTALLATION:
❑3/8" ratchet socket set with extensions and sockets ❑Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑Combination set of open-end wrenches ❑Liquid penetrant, anti-seize compound
SPECIAL NOTICE: This Edelbrock part has received an Executive Order (E.O. #) from the California Air Resources Board
(C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions
equipment certification, we have included a silver fan shroud decal to help testing personnel verify that this part is a legal
replacement part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your fan shroud
next to the existing emission and engine specification decal. Do not cover your original equipment specification decal with
the Edelbrock fan shroud decal.
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your
headers. Those products can cause excessive heat and moisture buildup resulting in corrosion and early
failure of the system.
NOTE: High temperature spark plug wires and boots are recommended to withstand heat from Headers.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
©2006 Edelbrock Corporation
Rev. 5/06 - DA/mc Catalog #68452, #68453
Brochure #63-68452
Page 2 of 2
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: (800) 416-8628
Office: (310) 781-2222
E-Mail: [email protected]
• DISASSEMBLY
1. Disconnect negative cable from battery.
2. Use penetrating oil on all nuts and bolts to be
removed. This will prevent the possibility of
broken or stripped nuts and bolts.
3. Unbolt exhaust pipes from both exhaust
manifolds.
4. Unbolt and remove both exhaust manifolds.
5. Clean and inspect all sealing surfaces before
assembly.
• ASSEMBLY - LEFT SIDE
1. With manifold port gasket in place, start a
header bolt with lock and flat washer in the
rearmost bolt hole leaving enough room for the
manifold to slip into position.
2. Start balance of header bolts with lock washers
and tighten evenly.
• ASSEMBLY - RIGHT SIDE
1. With gasket in place, start all bolts except the
rear bolt with lock and flat washers on each.
2. Start rear bolt with A.I.R. tube support bracket in
place.
3. Tighten balance of header bolts evenly.
4. Re-attach exhaust pipes to TES manifolds using
your original nuts.
5. Connect all parts including battery.
6. Start engine and bring up to normal running
temperature, then turn off and let cool.
7. When cool, re-tighten all manifold nuts and bolts.
INSTALLATION INSTRUCTIONS
HARDWARE SUPPLIED
Catalog #68452 (Ceramic-Coated), #68453 (Ti-Tech Coated)
Qty.Description Qty.Description
❑1 #25-9269 Header left side (#68452) ❑16 Header bolts; 3/8”-16 x 1”
❑1 #25-9272 Header right side (#68452) ❑16 Lockwashers; 3/8”
❑1 #25-9036 Header left side (#68453)
❑1 A.I.R. tube support bracket
❑1 #25-9035 Header right side (#68453)
❑1 Hex nut; 1/4” - 20
❑2 Manifold port gaskets ❑1 Lockwasher; 1/4”
❑4 Flat washers; 3/8” ❑1 Hex cap screw; 1/4”-20 x 3/4”
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Edelbrock Ricambi per automobili
Edelbrock
Edelbrock Russell 694300 Manuale utente
Edelbrock
Edelbrock Acura Integra 6737 Manuale utente
Edelbrock
Edelbrock THUNDER SERIES AVS 1803 Manuale utente
Edelbrock
Edelbrock 3581 Manuale utente
Edelbrock
Edelbrock 5282 Manuale utente
Edelbrock
Edelbrock 90 V6 200 Manuale utente
Edelbrock
Edelbrock 15010 Manuale utente
Edelbrock
Edelbrock 8135 Manuale utente
Edelbrock
Edelbrock Harley Nitrous Systems 63-0052 Manuale utente
Edelbrock
Edelbrock 16211-MBN-640 Manuale del proprietario
Edelbrock
Edelbrock Honda/Acura B-Series 4730 Manuale utente
Edelbrock
Edelbrock 66693 Manuale utente
Edelbrock
Edelbrock 1997 Manuale utente
Edelbrock
Edelbrock 67452 Manuale utente
Edelbrock
Edelbrock 3886 Manuale utente
Edelbrock
Edelbrock 4254 Manuale utente
Edelbrock
Edelbrock 25-9492 Manuale utente
Edelbrock
Edelbrock 24502574 LT4 Manuale utente
Edelbrock
Edelbrock 1711 Manuale utente
Edelbrock
Edelbrock 7577 Manuale utente
