Edimax EW-7238RPD Manuale utente

EW-7238RPD

Quick Installation Guide

11-2012 / v1.0

Before you start using this product, please check if there is anything missing in

the package, and contact your dealer to claim the missing item(s):

LED

Color

LED Status

Description

Signal Strength

2.4 GHz

Amber

Excellent signal.

Signal strength: 60 –100%.

Slow

Flashing

Good signal.

Signal strength: 60 –40%.

Quick

Flashing

Poor signal.

Signal strength: below 40%.

Off

No signal detected or in LED

off mode.

EW-7238RPD

Ethernet Cable

CD with User Manual &

Quick Installation Guide

Access Key Card

Package Contents

LED Status

LED

Color

LED Status

Description

Signal Strength

5 GHz

Amber

Excellent signal.

Signal strength: 60 –100%.

Slow

Flashing

Good signal.

Signal strength: 60 –40%.

Quick

Flashing

Poor signal.

Signal strength: below 40%.

Off

No signal detected or in LED

off mode.

Power

Green

Wi-Fi extender is on.

Flashing

Resetting to factory defaults,

or system is booting up.

Off

Wi-Fi extender is off or in

LED off mode.

WPS

Green

WPS connection established

(LED remains on for 5

minutes after connection is

made).

Slow

Flashing

WPS in progress (waiting for

another WPS device’s

connection).

Off

No WPS in progress or in LED

off mode.

LAN

Green

LAN port connected.

Flashing

LAN activity (transferring or

receiving data).

Off

LAN port not connected.

There are two ways you can quickly setup the Wi-Fi extender - using

browser-based iQ Setup (steps 1 - 15 below) or using the WPS button (see

WPS Setup).

Note: It is recommended that you plug in the extender

close to your router/access point for the setup process.

You need to establish a connection between your

extender and router/access point. After setup is

complete and a connection is established, you can

move the extender to your preferred location.

Note: Before you use the wireless extender, please

make sure your computer is set to use a dynamic IP

address. This is a simple procedure, and step by step

instructions for how to do this can be found in the user

manual.

1.Plug the Wi-Fi extender into a power outlet close to the root wireless

access point and switch it on. The power LED ( ) will flash while the

extender initializes –please wait. The extender is ready when the power

LED is on.

2.You can connect to the Wi-Fi extender using a (i.) wired or (ii.) wireless

connection.

Note: Please disable any other Wi-Fi adapters you

may have, and/or disconnect/disable any other

Ethernet cables/adapters from your computer.

Installation

i. Plug one end of the Ethernet cable into the Wi-Fi extender’s

Ethernet port. Plug the other end of the cable into your computer’s

Ethernet port.

i. Use your Wi-Fi device (e.g. computer, tablet, smartphone) to

search for a Wi-Fi network with the SSID “Edimax.Setup” and

connect.

3.Open a web browser (http://edimax.setup) and you will see the following

screen, please click “Get Started”.

Note: You can change language using the drop down

menu in the top right corner.

SSID:

Edimax.Setup

4.iQ Setup will display all available 2.4GHz and 5GHz Wi-Fi networks, listed

under “SSID”. Please select one or both root Wi-Fi networks that your

extender will connect to and subsequently extend. If you don’t wish to use

either the 2.4GHz or 5GHz band you must select “Disable” in order to

continue.

Note: If the Wi-Fi network you wish to connect to does

not appear, click “Refresh” to search again. Please

also be aware that for the 5GHz band, subject to local

RF regulations the EW-7238RPD only supports

channels 36, 40, 44 & 48 (Europe) and channels 36, 40,

44, 48, 149, 153, 157, 161 & 165 (U.S.) If you do not

see your 5GHz network listed, you may need to change

your router/access point’s 5GHz channel.

5.If the network you wish to connect to has a hidden SSID, select “Setup

extender manually” and enter the SSID manually. Then input a “Device

SSID” and security key information – please refer to the user manual for

more detailed guidance.

6.For each network you select, you can enter a “Device SSID” which is a name

to identify the EW-7238RPD’s Wi-Fi network. If the root SSID requires a

security key, you will also be required to enter it here.

Note: If you do not know your existing network

security key, please refer to the user manual for help.

Note: In the example above, the EW-7238RPD will

connect to the root Wi-Fi network OBM-Airport-2.4G.

The EW-7238RPD will extend this Wi-Fi network and

use the new SSID OBM-Airport-2.4G_2EX to identify

itself.

7.Click “Next” to continue and you will be prompted to add

http://edimax.setup to your bookmarks (Internet Explorer and Firefox only).

This is the URL to access the extender’s browser based configuration

interface to further configure the settings of the extender, or to run iQ

Setup again. If you do not wish to add this URL to your bookmarks, click

“Cancel” – or select “No” from the drop down menu shown below, before

you click “Next”.

8.Please wait while the Wi-Fi extender tests the connection.

9.When the test is complete, click “Apply” to restart the device.

Note: If the extender cannot obtain an IP address from

the router/access point then you will see the screen

below. Click the “Static IP” button to assign an IP

address to the extender and then click “APPLY” to

restart the device.

Note: When assigning a static IP address to the

wireless extender, you need to ensure that you assign

an IP address in the same subnet as your network. For

example, if your static IP is 192.168.9.2 then you need

to assign the wireless extender an IP address in the

range 192.168.9.x where x = 3 –254.

Note: To ensure that you assign a correct IP address to

the wireless extender, you can check the IP address of

your computer and/or router. Please refer to the user

manual for guidance on how to do so. Your ISP can

also provide you with such information as IP address,

subnet mask and gateway address.

10. Please wait while the device restarts.

Note: After the system has restarted, if you do not see

the congratulations screen in Step 11, then please skip

straight to step 12.

Typically, this may occur for smartphone users who

setup the extender via a wireless connection (as

shown in II-1. iQ Setup 2.ii). It is likely that after the

extender restarted, your smartphone re-connected to

the Edimax.Setup SSID which is now, upon completion

of setup, redundant.

11. After the device has restarted you will see a congratulations screen as

shown below, displaying the name and security key for each of the

extender’s Wi-Fi networks.

12. The extender is now functional and ready for use. If you wish to move

the extender to another location, remember to switch off the extender

before you unplug it. For the best coverage, select a location where the

extender’s signal strength LED ( )displays a strong signal.

Altri manuali per EW-7238RPD

Indice

Altri manuali Edimax Estensione

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuale utente