Edsyn Soldavac TSX70 Manuale utente
EDSYNÆINC. PHONE(818)989-2324 FAX(sales):818-997-0895 FAX(service):818-997-0460
instruction manual
Hot Gas + Hot Tip
Desoldering
MADE
IN
U.S.A.
SMT Reflow Vacuum
Workstation
ï COMPLIES WITH MIL-S-45743E, MIL-STD-2000, DOD-STD-2000-1B,
WS6536E AND ESD SPEC, DOD-STD-1686, DOD-HDBK-263
TSX70
Solder-Handling Station
(Hot Gas & Hot Tip Desoldering)
5.
7.
7.
8.
9.
10.
12.
6.
4.
3.
° ° ° °
Solder-Handling Station
(Hot Gas & Hot Tip Desoldering)
(B
C)
A)
E)
F)
G)
D)
ï Tool should be place in
Holder when not in use.
ï Hot Gas flow will stop if Tool
is placed in the Holder.
DAMAGED CORD SHOULD
ONLY BE REPLACE BY AN
EDSYN-CERTIFIEDTECHNICIAN
Hand Tool
FEATURES
A ) Gas Heater.
B) Desoldering Head Housing.
C) Desoldering Tip.
D) 24V Power Input, turn clockwise to engage.
E) Gas Connector, turn clockwise to engage.
F) Vacuum Line, connect to AFX73.
G) Trigger, activates vacuum.
H) Cleaning Tool.
Power Supply
FEATURES
(A
(C
(F
(J
(H
(M
(B
(E
(D
(I
A ) Tool Pod, equipped with micro-switch to activate gas & vacuum.
B) Gas Flow Control in standard cubic feet per hour delivered to
Desoldering Tip.
C) Power Switch, to activate WorkStation.
D) Temp. Control Knob, Heater for Desoldering.
E) Temp. Control Knob, Heater for Gas.
F) SH232 Sponge Holder, with cleaning sponge.
G) Gas Output, controlled flow.
H) Power output, 24V, controlled
I) WT623 Tip Wrench
J) AFX73 Filter, NOTE VACUUM FLOW DIRECTION.
K) Gas Input, color coded sleeve.
L) Shop air input.
M) CSX70 Cleaning Tool
(G
(K
(L
ESD Safe
°C).
°F
ADJUSTMENT
While Tool is in the
Pod, push handle
down and twist.
Twist until it locks into 1 of it's 4 positions.
Twisting counter-clockwise will permit a 1800
turn. Twisting clockwise will permit a 900turn.
Note: Head Assembly does not make a full 3600turn
Use this wrench to remove
or intall tips
CHANGING TIP
TSX713
Desoldering Tip
INSTALLING:
Tighten this last
Tighten this first
Should be done while the tool is
cool.
REMOVING:
Loosen this first
Lossen this last
adjustment
screws
To tilt the Head Assembly, loosen (2) Adjust-
ment Screws. Tilt the Head Assembly to de-
sired position and retighten screws.
Tip
Cleaning Shaft Handle
Retaining Sleeve
ITISRECOMMENDEDFOR THE
OPERATOR TO REMOVE AND
INSPECTTHE TIPDAILY.
REPLACE TIP THERE IS ANY SIGN OF
CORROSION . DOING THIS WILL
ALSO PREVENT THE TIP FROM
SEIZING ON TO THE HEATER.
Before tightening the Retaining
Sleeve
Check tip alignment by inserting the end of the
Cleaning Shaft handle inside the tip, then tighten
Retaining Sleeve
AF625
OS133
SC525
MS229
FC639
OS130
OS132
LockNut Handle
Cover
Trigger
Place inside Housing & push O-Ring over HT01.
REMOVE GUIDE AFTER USING.
Hook
TSX70 Tool Housing
Place Cleaning Shaft & Tip/O-Ring Guide in HT01 Tube.
SafetyCover
Cleaning Shaft Holder
Spring Seat
OS730
O-Ring Set
To clean wall of Housing, Remove
Mica Sheet.
Rotate Cleaner while pushing in.
Push Cleaner all the way to remove
HT01 Tube.
Remove O-Ring by using the Hook.
HT01
OS133
HT01 & OS133 Replacement
Cleaning the Desoldering Head Housing
O-Rings Replacement
inside Valve Assembly
a) Unscrew Lock Nut at the end
of the Tool Handle.
b) Remove Handle Cover.
c) Slide out Valve Assembly
while placing your finger
over the Spring Seat. BE
CAREFUL NOT TO LET THE
SPRING AND THE SPRING
SEAT SHOOT OUT FROM
THEHOUSING
d) Clean all parts with alcohol
only.
e) Replace OS730 O-Ring Set
(set of 3).
f) Lube new O-Rings with
OL111 O-Ring Lube.
Make sure wires and hoses
are
not pinched or kinked.
CLEANING & MAINTENANCE
1. Replace AF625 Filter.
2. Clean SC525.
3. Clean or replace OS133 if neccessary.
4. Replace MS229.
5. Replace worn-out Tip.
INSPECT OVER-ALL TIP
CONDITIONREGULARLY.
AF110S Silencer
AFX73 Maintenance
Install as shown
AF629
Felt Filter
(insert inside cap)
AF040
Foam Filter
SR305
SR304
AF040
Foam Filter
SR266
in
out
If flux gets in the venturi, disconnect the AFX73 and
AF110S. Flush the venturi with alcohol. You may
need to pump the alcohol through the venturi.
Replace dirty Filter Element.
Clean SR304 and SR305 with
alcohol.
Tip Wrench can be
used to remove SR266
filter cap.
SR533 AF040 SR636
WT623
CSX70 AF110S
3
DESCRIPTION
1SR341 Heater Assy. 24V, Hollow Threaded 1
2SR342 Housing, Hot Gas Heater 1
3SR343 Set Screw 1
4HS304 Low Static Silicone Hose, 3/32 i.d. 2
5HT01 Hot Tube 1
6AC737 Accumulator Bushing 1
8SR007 Nut, Hex, 2-56 3
9SR170 Nut, Hex, Cap, 8-32 1
PART NO.
ITEM
NO.QTY
REQ'D
TSX70-1 ÆSOLDER HANDLING TOOL SPARE PARTS LIST
Altri manuali per Soldavac TSX70
1
Indice
Altri manuali Edsyn Scrivania
