Eelectron IPSBA01KNX Manuale utente

USER MANUAL

Translation of the original instructions

Version: 1.0

Date: 06/06/2023

IPSBA01KNX Knx bridge with ip interface and power supply knx + aux 640ma + MQTT

IPSBA01KNX

2IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

Index

1. Introduction to the user manual ................................................................................................................................................4

Meaning of the symbols used ................................................................................................................................................. 4

2. Product overview ......................................................................................................................................................................4

3. Installation instructions ..............................................................................................................................................................4

4. Congurationandcommissioning.............................................................................................................................................5

5. General parameters ..................................................................................................................................................................5

General settings...................................................................................................................................................................... 5

Surveillanceconguration....................................................................................................................................................... 6

Logicsconguration................................................................................................................................................................ 6

Networkconguration ............................................................................................................................................................. 6

6. Diagnostic .................................................................................................................................................................................7

7. Surveillance ..............................................................................................................................................................................7

8. Timer ......................................................................................................................................................................................... 7

9. Logics ........................................................................................................................................................................................7

10. MQTT ........................................................................................................................................................................................7

11. Behaviour on bus failure, recovery and download ................................................................................................................... 7

Behaviour on bus voltage failure ............................................................................................................................................ 7

Behaviour on bus voltage recovery ........................................................................................................................................ 7

Wrong application download................................................................................................................................................... 7

VERSION DATE CHANGES

1.0 06/06/2023 -

IPSBA01KNX

3IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

Any information inside this manual can be changed without ad-

vice.

This handbook can be download freely from the website:

www.eelectron.com

Exclusion of liability:

Despite checking that the contents of this document match the

hardware and software, deviations cannot be completely exclu-

ded. We therefore cannot accept any liability for this.

Any necessary corrections will be incorporated into newer ver-

sions of this manual.

Eelectron S.p.A.

Via Claudio Monteverdi 6, I-20025 Legnano (MI), Italia

Tel +39 0331.500802 [email protected]

IPSBA01KNX

4IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

1. Introduction to the user manual

This manual is intended for use by KNX installers and describes

functions and parameters of the IPSBA01KNX device and how

thesettingsandcongurationscanbechangedusingtheETS

software tool.

For the technical data of the device and the compatible accesso-

ries, please refer to the datasheet of the device itself.

Meaning of the symbols used

WARNING - The operation or phase described must be

carried out in compliance with the instructions provided

and with the safety standards.

IMPORTANT NOTE - Detailsandspecicationstobere-

spected for the correct functioning of the device.

2. Product overview

The IPSBA01KNX device integrates a KNX power supply with

auxiliary output with a a total current of 640mA, and an IP inter-

face, allowing KNX installations to be implemented quickly and

e󰀩ciently.

The voltage of the bus output as well as that of the auxiliary

output is 29V DC.

The IP address can be obtained via DHCP server or manually

conguredviaETS®.

ThedeviceworksinaccordancewiththeKNXnet/IPspecica-

tions;upto5di󰀨erentIPaddressescanbeassigned.Thedevice

is also a KNX bus node, with its own application program and

canbeconguredwithETS®tocommunicateusingKNX Data

Secure protocol.

The device integrates the MQTT protocol which can manage

publications and subscriptions of a server up to 160 objects. By

enablingthespecicparameteronETS,theMQTTversionwith

TLS is available, which features mutual authentication based on

certicate (server and device) and encryption. The purpose of

thecerticateistoguaranteetheidentityoftheserver(broker),

oftheclient(bridge)andtotransmitdatainasecureway.

The uploading of the certicates is managed by the software

“EelectronCerticateLoader”propertyofeelectron.Pleaserefer

tothespecicusermanual“EelectronCerticateLoader”.

ByenablingtheETS“Other power supplies on the BUS line”

parameter, it is possible to install two devices on the same bus

line, at a minimum distance of 200 metres.

Moreover, 48 logic blocks are available to implement simple ex-

pressions with logical or threshold operator or complex expres-

sions with algebraic and conditional operators; It is possible to

usepredened algorithmsas proportionalcontrolsof tempera-

ture and humidity or dew point calculation.

The device also integrates the “Virtual Holder Logic”;theeld

of application is the hotel room: through a magnetic sensor in-

stalled on the door and connected to a digital input, accurate

presence information is managed. The presence detection solu-

tion can deduce the presence of people in the room using one or

more dedicated sensors. It also detects an unexpected presence

andisabletodi󰀨erentiatemorebehaviors.

It is also implemented the control logic called “OnLine-O󰀨Line”

that checks if all KNX TP devices of the subnet connected to the

powersupplyare operating“On Line”,alerting thebackboneif

oneofthemgoesinto“O󰀨Line”status.

OnthedevicetherearepushbuttonsandsignalingLEDsforbus

reset operations as well as for Factory Reset or for displaying

activity on the KNX bus and on the IP backbone.

The device is compact, with a size of only 4 DIN modules and

is intended for installation on DIN bar in LV distribution switch-

boards.

3. Installation instructions

The device can be used for permanent internal installations in

dry places.

WARNING

• When a clear separation between the low voltage (SELV)

andthedangerousvoltage(230V)isNOTpossible,thede-

vice must be installed maintaining a minimum guaranteed

distance of 4 mm between the dangerous voltage lines or

cables (230V not SELV) and the cables connected to the

EIB/KNXBUS(SELV).

• The device must be mounted and commissioned by an au-

thorized installer.

• The applicable safety and accident prevention regulations

must be observed.

• The device must not be opened. Any faulty devices should

be returned to manufacturer.

• For planning and construction of electric installations, the re-

levant guidelines, regulations and standards of the respecti-

ve country are to be considered.

• KNX bus allows you to remotely send commands to the

system actuators. Always make sure that the execution of

remote commands do not lead to hazardous situations, and

that the user always has a warning about which commands

can be activated remotely.

For more information: www.eelectron.com.

IPSBA01KNX

5IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

4. Conguration and commissioning

Thecongurationandcommissioningofthedeviceismadewith

theETS®(EngineeringToolSoftware).Forthecongurationof

the device parameters the corresponding application program or

thewholeeelectron® product database must be loaded in the

ETS®program.

The commissioning of the device requires the following steps:

• connectthebusKNX(1)

• turn on the bus power supply

• press the programming button (2); the red programming

LEDturnsON

• download into the device the physical address and the con-

gurationwiththeETS®program

5. General parameters

InETS®,inthedropdownmenuofthedevicethegeneralpa-

rameters consist of four conguration blocks, described in the

next paragraphs.

General settings

Communication objects involved:

“<General>Heartbeat” 1 Bit CRT

“<General>PowerOnEvent” 1 Bit CRT

“<General>InputDate” 3 Bytes CWTU

“<General>InputTime” 3 Bytes CWTU

“<General>OutputDate” 3 Bytes CRT

“<General>OutputTime” 3 Bytes CRT

“<General>IPInterface” 1 Bit CW

“<General>ResetBUS” 1 Bit CW

“<General>PrimaryHeartbeat” 1 Bit CW

“<General>PrimaryAlarm” 1 Bit CRT

PARAMETRO KNX IMPOSTAZIONI

Delay to send telegrams on

power-up 5 ÷ 15 secondi

Through this parameter it is possible to set the telegram transmission

delay after switch-on by selecting the time beyond which the device is

authorized to send telegrams.

In large systems after a power outage or shutdown, this delay avoids

generatingexcessivetra󰀩conthebus,causingslowperformanceor

a transmission crash.

If there are several devices that require telegrams to be sent on the

busafterareset,thesedelaysmustbeprogrammedtopreventtra󰀩c

congestion during the initialization phase.

Input detection and object values are updated at the end of the trans-

mission delay time

AttheendofETSprogramming,thedevicebehavesasitdidafterit

was switched on.

Other power supplies on the

BUS line no / yes

By enabling this parameter it’s possible to install two devices on the

same bus line, at a minimum distance of 200 metres.

Heartbeat

(periodic alive notication)

nothing

periodic

on request

The parameter allows you to notify a hierarchically superior control

or supervision system of your existence / correct online activity. The

noticationcantakeplacespontaneously(periodically-settableperi-

odvalue)orfollowingaquery(uponrequest).Thevalueofthe1-bit

noticationtelegramcanbeset.

Telegram value o󰀨/on/toggle

Denesthevalueofthe1bitnoticationtelegram.Thetogglevalueis

notavailablefor“ondemand”conguration.

Period - time unit seconds / minutes / hours

Denestheunitofmeasureofthenoticationtimeinterval.Thispa-

rameterisnotavailableforthe“ondemand”conguration.

Period - time value 1 ... 255

Denesthe noticationintervaltime.This parameterisnotavailable

forthe“ondemand”conguration.

Date and time source for timers fromBUS/fromNTPserver

DeneswetherthetimedataaretakenfromtheBUSlineortheNTP

server.

Request time at power ON no / yes

IncaseofdateandtimedatasourcingfroBUS,thisparameterpermits

to enable a time request at power ON.

Output date objects Date and Time / DateTime

Denes whether the relay outputs are managed individually or cou-

pled.

Cyclic send time

never / every minute / every 30

minutes / every hour / every 6

hours / every 12 hours / every

day

Set the period of cyclical sending.

Timezone mode custom / standard

In custom mode it is possible to set manually the coordinates

In standard mode the location is chosen from the drop down menu.

IP interface always enabled / bus controlled

With this parameter it is possible to set how to manage the IP interface

function.

KNX BUS

AUX 29V DC

LAN

IPSBA01KNX

PSU WITH IP INTERFACE

RESET POWER

OVERLOAD

ADDRESS

PROG.

TP LAN FACTORY RESET

STATUS

iBUS + iAUX ≤ 640mA

BUS 29V DC

180 - 265V AC

AUX 29V DC

50/60Hz

IPSBA01KNX

6IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

Bus controlled

Initial enable state disabled / enabled

Itdenes the initial state of the IPinterface function when bus con-

trolled.

Enable activation telegram telegram“0”/telegram“1”

Itdenes the telegram sent totheobject “<General>IPInterface” to

enable the function.

Automatic deactivation time

(0=never) [min] 0 ... 255

Itdenestheautomatictimeafterwhichthefunctionisdeactivated.

Reset BUS object disabled / enabled

With this parameter it’s possible to enable the object “<General> Re-

setBUS”.

Telegram for reset telegram“0”/telegram“1”

Itdenesthetelegramsenttotheobject“<General>ResetBUS”to

enable the reset.

Additional function x

4 logics

20 MQTT channels

1 virtual holder

With this parameter it is possible to enable this functions:

4 logics-see“Logic”usermanual

20 MQTT channels -

1 virtual holder - is a logical function that automatically recognizes the

presence of a person in a room. This function can be used in hotels

orsimilarinstallationsandrequiresconnectiontootherdevices(see

“Virtual Holder”).

Surveillance conguration

Communication objects involved:

“<General>Alarms0-15” 4 bytes CRT

“<General>Alarms16-31” 4 bytes CRT

“<General>Alarms32-47” 4 bytes CRT

“<General>Alarms48-63” 4 bytes CRT

“<General>Alarms64-79” 4 bytes CRT

“<General>Alarms80-95” 4 bytes CRT

“<General>Alarms96-111” 4 bytes CRT

“<General>Alarms112-127” 4 bytes CRT

These objects are used to sum up the alarm status of the relative sur-

veillance channels.

KNX PARAMETER SETTINGS

Physical address main line 0 .. 255

This parameter denes the physical main address of the surveilled

devices(e.g.10.13.x-->10).

Physical address sub line 0 .. 255

Thisparameterdenesthephysicalsubaddressofthesurveilledde-

vices(e.g.10.13.x-->13).

Alarm time - hours 0 ... 255

Thisparameterdenesthesurveillance time (hours) beforesending

thealarm.Usedbythesurveillancemoduleswhenthealarmfunction

is enabled.

Alarm time - minutes 0 ... 255

Thisparameterdenesthesurveillancetime(minutes)beforesending

thealarm.Usedbythesurveillancemoduleswhenthealarmfunction

is enabled.

Warning time - seconds 20 ... 255

Thisparameterdenesthewarningtime(seconds).Thistimeindicates

how much before the end of the surveillance time a group value read is

sentonthebusthroughthe“WarningReadRequest”object.Usedby

the surveillance modules when the warning function is enabled.

Surveillance priority primary / secondary

Thisparameterdenesifthedeviceistheprimarysurveillancedevice

or if it is the secondary one. If secondary is selected, the heartbeat

period of the primary device must be aligned to the one of the primary

device itself. If no message is received in the period an alarm message

issent onthe object “<General> PrimaryAlarm” and the secondary

device starts to surveil the plant.

Primary period - time unit seconds / minutes / hours

ThisparameterdenestheunitofmeasuresofthePrimaryHeartbeat

period.

Primary period - time value 1 ... 255

Thisparameter denes thetime interval forsending the “<General>

PrimaryHeartbeat”object.

Number of surveillances 16, 32, 48, 64, 80, 96, 112, 128

Thisparameterdenesthenumberofsurveillancemodules.

Logics conguration

Communication objects involved:

“<General>Enable/DisableAllLogics” 1 Bit CW

“<General>Enable/DisableLogicx” 1 Bit CW

KNX PARAMETER SETTINGS

Logic activation telegram telegram“0”/telegram“1”

Denesthetelegramsentontheobject“<General>Enable/DisableAll

Logics”toenablethelogicfunction.

Logic x enabled/disabled state

after download disabled / enabled

Thisparameter denes thevalue set for object ““<General>Enable/

DisableLogicx”afteradownload.

Logic x enable/disable object do not use / use

Withthisparameterit’spossibletousetheobject“<General>Enable/

DisableLogicx”.

Network conguration

This function allows the device to communicate with the DNS

(DomainNameSystem)andNTP(NetworkTimeProtocol)ser-

vices,tobeconsideredmandatoryfortheETSIPconguration.

To guarantee the correct functioning of the validation of the secu-

ritycerticatesandtheidentityofthebrokertowhichtoconnect

with the MQTT service, the device must reach the NTP and DNS

services.

In addition to the MQTT part, the NTP service is required to use

the object dedicated to sending the date and time via KNX.

Communication objects involved:

“<General>AlarmDHCP” 1 Bit CRT

“<General>AlarmPing” 1 Bit CRT

“<General>AlarmDNSResolution” 1 Bit CRT

“<General>AlarmNTP” 1 Bit CRT

IPSBA01KNX

7IPSBA01KNXFI00020100_UM_EN_1.0

MEMBER

“<General>Alarm4Bytes” 4 Bytes CRT

“<General>AlarmText” 14 Bytes CRT

KNX PARAMETER SETTINGS

DNS 1 address max 15 bytes

Withthis parameter (Domain Name System) it’s possible to convert

awebaddressinanIPaddresswhichuniquelyidentiesthedevice.

DNS 2 address max 15 bytes

This parameter it’s used in case of failure of DNS 1.

DHCP alarm disabled / enabled

Thisparameter(DynamicHostCongurationProtocol)isusedtoas-

signIPaddresses andothernetwork congurations automatically to

devices that connect to a network.

This parameter allows a message to be sent to the bus which warns

whether or not the protocol has correctly released the IP address to

the device.

Alarm telegram telegram“0”/telegram“1”

It denes the value sent to the object “<General>Alarm DHCP” to

activate the alarm.

Cycling ping alarm disabled / enabled

Ping is a command that is used to verify the network connection be-

tween two devices. Ping works by sending a packet of data from one

device to another.

Ping is often used to check if a given IP address or hostname is reach-

able across a network connection. For example, you can use ping to

check if a server is able to respond to connection requests or to diag-

nose network connection problems.

This parameter allows a message to be sent to the bus which warns if

the IP address/DNS has responded correctly to the request.

Address to ping max. 32 bytes allowed

ItdenestheIPaddress/DNSthedevicewillconnectto.

Alarm telegram telegram“0”/telegram“1”

Itdenesthevaluesenttotheobject“<General>AlarmPing”toacti-

vate the alarm.

Cyclic time [min] 1 ... 60

Itdenesthetimeintervalforpingrequest.

DNS resolution alarm disabled / enabled

This parameter allows a message to be sent to the bus which warns if

atleastoneoftheconguredDNSfunctionscorrectly(seeDNS1/2).

Domain name max. 32 bytes

ItdenesthenameoftheIPaddress/DNStoresolve.

Alarm telegram telegram“0”/telegram“1”

Itdenesthevaluesenttotheobject“<General>AlarmDNSResolu-

tion”toactivatethealarm.

Server x (1- 4) max. 32 bytes

NetworkTimeProtocol(NTP)isanetworkprotocolthatisusedtosyn-

chronize the system time of a device on the network with a time server.

We have 4 servers available to ensure time synchronization, if server

1 fails the request is passed to 2 and so on up to 4.

NTP alarm disabled / enabled

This parameter allows a message to be sent to the bus which warns

ifat least 1 of the congured NTPservers is working correctly(see

Server1/2/3/4).

Alarm telegram telegram“0”/telegram“1”

Itdenesthevaluesenttotheobject“<General>AlarmNTP”toacti-

vate the alarm.

Alarm 4 bytes disabled / enabled

This parameter enable the object “<General>Alarm 4 Bytes” which

sendstotheBUSabitmaskcontainingthenetworkerrors.

Alarm text disabled / enabled

Thisparameterenabletheobject“<General>AlarmText”whichsends

atextstringcontainingnetworkerrorstotheBUS.

6. Diagnostic

Please refer to the “Diagnostic”usermanual.

7. Surveillance

Please refer to the “Surveillance”usermanual.

8. Timer

Please refer to the “Timer”usermanual.

9. Logics

Please refer to the “Logics”usermanual.

In the devices described, the logical expression can

have a maximum of 24 characters.

10.MQTT

Please refer to the “MQTT”usermanual.

11.Behaviour on bus failure, recovery and

download

Behaviour on bus voltage failure

On failure of bus voltage, it’s possible to set an action to execute

in case of independent relays. Behaviour of controlled actuators

must be set using their own parameters.

Behaviour on bus voltage recovery

On bus voltage recovery all the communication objects are set

to0exceptforobjectsforwhichaparameterisdenedforthe

initial value.

Wrong application download

If the wrong ETS application is downloaded then KNX/EIB led

starts blinking and device is not operative on the bus. A power re-

setmustbedoneorthecorrectETSapplicationmustbedownlo-

aded.

Indice

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente