Ego Power+ CS2000E Manuale utente
OPERATOR’S MANUAL
56 VOLT LITHIUM-ION
CORDLESS CHAINSAW
MODEL NUMBER CS2000E
MNL_EGO_CS2000E_AV02.01_231101
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
1
3. Chain-
kickback Brake
Paddle
4. Front Handle
5. LCD Screen
13. Lock-off
Button
26. Chain Sheath
7. Bluetooth®Icon
8. Headlight Icon
9. Brake
Icon
1. Saw Chain
2. Bucking Spikes
20. Lubricating
Hole
19. Guide Bar
18. Oil-tank Cap
17. Oil-inspection
Window
16. Battery Release Button
14. Trigger Switch
15. Rear Handle
12. Chain Speed
Button
6. Speed Bars
11. Headlight/
Bluetooth®Button
10. Fuel-gauge
Circle
25. Double-
end Socket
Wrench
23. LED
Headlight
24. Chain-tensioning Bolt21. Side Cover
22. Side Cover Nuts
CB
Chain kickback brake paddle
in operating position
Chain kickback brake paddle
in brake position
E
F
H
I
D
J
G
Side Cover Lock Nuts
Chain-
tensioning Bolt
Guide Bar Groove
Chain Drive Links
Chain Drive Links
Chain Cutters
Rotation Direction
Pull
Push
Rotation
Direction Arrow
K2
LM
O
P
K1
Sprocket
1.3mm
Chain-tensioning Bolt
N
Q
Sensors will NOT detect
sudden motion in this
plane.
Sensors WILL detect
sudden motion in this
plane.
Lock-off Button
Trigger Switch
Gripping Area
SR
U1
V2
U2
SPEED
Bluetooth®
Icon
Speed
Bars
Headlight Icon Brake Icon
Fuel-gauge
Circle
Headlight/
Bluetooth®
Button
Chain
Speed
Button
T
High Brightness Headlight Icon
LED Headlight
Low Brightness Headlight Icon
V1 Grip with thumb
below handle
Chain line
V3
Chain line
Straight Arm
Position
45°
W1
Dangerous Zone
Dangerous
Zone
Felling Direction
Safety
Retreat Path
Safety
Retreat Path
W2 Notching
Undercut
Felling back
cut
Direction of fall
Notch
Hinge
50.8 mm
50.8 mm
W3 Tree Limbing
Limb Cut
X1
X2
Log Supported Along the Entire Length
Cut From Top (Overbuck)
Avoid Cutting Earth
Log Supported One End
2nd Cut Overbuck (2/3 Diameter) to Meet 1st Cut (To
Avoid Pinching)
1st Cut Underbuck (1/3 Diameter) to Avoid Splintering
X3 Log Supported Both Ends
1st Cut Overbuck (1/3 Diameter) to Avoid Splintering
2nd Cut Underbuck (2/3 Diameter) to Meet 1st Cut
(To Avoid Pinching)
YZ1
Lubricating Hole
Sprocket in
Guide Bar Tip
Z3Z2
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E8
READ ALL INSTRUCTIONS!
READ OPERATOR’S MANUAL
WARNING: To ensure safety and reliability, all
repairs and replacements should be performed by a
qualified service technician.
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention
to possible dangers. The safety symbols and the
explanations with them deserve your careful attention
and understanding. The symbol warnings do not, by
themselves, eliminate any danger. The instructions and
warnings they give are no substitutes for proper accident
prevention measures.
WARNING: Be sure to read and understand all
safety instructions in this Operator’s Manual, including all
safety alert symbols such as “DANGER”, “WARNING”,
and “CAUTION” before using this tool. Failure to follow all
instructions listed below may result in electric shock, fire,
and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING,
or CAUTION. May be used in conjunction with other
symbols or pictographs.
WARNING: The operation of any
power tools can result in foreign objects
being thrown into your eyes, which can
result in severe eye damage. Before
beginning power tool operation, always
wear safety goggles or safety glasses with
side shields and a full face shield when
needed. We recommend a Wide Vision
Safety Mask for use over eyeglasses or
standard safety glasses with side shields.
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may
appear on this product. Read, understand, and follow
all instructions on the machine before attempting to
assemble and operate.
Safety Alert Indicates a potential
personal injury hazard.
Read
Operator’s
Manual
To reduce the risk of
injury, user must read
operator’s manual.
Wear Eye
Protection
Always wear safety
goggles or safety
glasses with side shields
and a full face shield
when operating this
product.
Wear Ear
Protection
Always wear ear
protection when
operating this product.
Wear Head
Protection
Wear an approved safety
hard hat to protect your
head.
Wear
Protective
Gloves
Protect your hands with
gloves when handling
saw and saw chain.
Heavy-duty, nonslip
gloves improve your grip
and protect your hands.
500mm
AG2005
Guide Bar The information of guide
bar.
Be Aware
of Kickback
Beware of chainsaw
kickback and avoid
contact with bar tip
Guide
Bar Tip
Kickback
Tip contact can cause
the guide bar to move
suddenly upward and
backward, which can
cause serious injury.
Two
Handed
hold
Always use chainsaw
two-handed
Regulatory
Compliance
Mark
This product complies
with applicable
Australian standards.
XX
Noise Guaranteed sound power
level.
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E 9
Direct
Current
Type or a characteristic
of current
VVolt Voltage
A Amperes Current
Hz Hertz Frequency (cycles per
second)
WWatt Power
min Minutes Time
n0
No Load
Speed
Rotational speed, at
no load
... /min Per Minute Revolutions per minute
IPX4
Ingress
Protection
Degree
Protection From
Splashing Water
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term “power tool” in the warnings refers to your
mains- operated (corded) power tool or battery-operated
(cordless) power tool.
WORK AREA SAFETY
◾Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
◾Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
◾Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
ELECTRICAL SAFETY
◾Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adaptor
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock
◾Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
◾Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
◾Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
◾When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
◾If operating a power tool in a damp location is
unavoidable, use a Ground-fault circuit interrupter
protected supply. Use of GFCI reduces the risk of
electric shock.
PERSONAL SAFETY
◾Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol medication. A
moment of inattention while operating power tools may
result in serious personal injury.
◾Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
◾Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch
on invites accidents.
◾Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E10
◾Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
◾Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
◾If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
devices can reduce dust-related hazards.
◾Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second
POWER TOOL USE AND CARE
◾Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
◾Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
◾Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
◾Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
◾Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
◾Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
◾Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
◾Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces may lead to unsafe handling and/or
loss of control of the tool.
BATTERY TOOL USE AND CARE
◾Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
◾Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
◾When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
◾Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
◾Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or
risk of injury.
◾Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may cause explosion.
◾Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
SERVICE
◾Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
◾Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
CHAINSAW SAFETY WARNINGS
◾Keep all parts of the body away from the saw chain
when the chainsaw is operating. Before you start the
chainsaw, make sure the saw chain is not contacting
anything. A moment of inattention while operating
chainsaws may cause entanglement of your clothing or
body with the chain.
Indice
Altri manuali Ego Power+ Motosega
Ego Power+
Ego Power+ CS1614E Manuale utente
Ego Power+
Ego Power+ CS1401E Manuale utente
Ego Power+
Ego Power+ CS1610E Manuale utente
Ego Power+
Ego Power+ CS1400 Manuale utente
Ego Power+
Ego Power+ CS1800E Manuale utente
Ego Power+
Ego Power+ CS1400E Manuale utente
Ego Power+
Ego Power+ CS1610 Manuale utente
Ego Power+
Ego Power+ CS1610E Manuale utente
Ego Power+
Ego Power+ CS1800E Manuale utente
