EGO CS1400E Manuale utente
REPAIR GUIDELINE
CHAIN SAW_CS1400E
Version: 1
Issue Date: 2015/2/15
Table of Contents
2
NO. Contents Page
1 Troubleshooting 3-4
2 Tool list 5
3 Disassemble the product 6-9
4 Replace the PCBA 10-13
5 Replace the motor 14-15
6 Replace the oil tank assembly/Plastic gear 16
7 Assemble the product 17-31
Troubleshooting
3
Problem Possible Cause Fault Position Test & Solution
Fail to start/stops in
running
Weak connection of the
white cable
Battery
connection
terminals (base)
Open the housing, check if the white
cable that connects to the battery
connection terminal was insufficiently
soldered (weak connection), re-solder
the cable and check the function.
PCBA is broken PCBA Open the housing, replace the PCBA
Big deviation of the speed
sensor Motor assembly Open the housing, replace the motor
assembly
No oil lubrication
when cutting
Oiling hole in housing was
blocked by debris
Oil hole in
housing
Open the housing, clear the oil hole in
housing.
Oil pumper was blocked
by oil residue Oil tank assembly Open the housing, replace the oil tank
assembly
Plastic gear was worn out Plastic gear
Open the housing, replace the plastic
gear; check and clear the oil hole in the
housing.
Saw chain cannot or
hard to move in guide
bar
Guide bar was worn out Guide bar Replace the guide bar
Troubleshooting
4
Problem Possible Cause Fault Position Test & Solution
Saw chains slides on
the sprocket/big
noise
The sprocket was worn
out Sprocket Replace the sprocket
Noise Motor bearing was worn
out Motor Open the housing, replace the motor
assembly
Tool List For Repair
5
NO. Tool List SPEC Remark
1 Magnetic bits
2 Electric soldering iron
3 Heat gun
4 Heat shrinkable sleeves
5 Silicon glue Assist fixing the plug
6 Scissors To remove the shrinkable sleeve
7 Snap ring pliers To remove the E-ring
1. Remove the side cover, saw chain and guide bar from the chain saw;
Description Part Number SPEC
Side cover assembly 2823860000 ---
Saw Chain 3810637000 90PX052X (Oregon)
Guide Bar 3705657000 144MLEA041 (Oregon) 350mm (14”)
Disassemble the Product
6
2. Remove the E-ring, Gasket and Sprocket from the motor shaft.
Description Part Number SPEC
E-Ring 5660028000
Gasket 5660208000
Sprocket 3421564000
Disassemble the Product
7
3. Loose the four screws to remove the front handle from the housing.
Description Part Number Quantity
Tapping screw 5610042000 4 pcs
Front Handle 3127504000
Disassemble the Product
8
4. Remove the oil tank and loosen the screws in housing, total 12 pcs.
5. Open the housing.
Description Part Number Quantity
Tapping screw 5610042000 12 pcs
Disassemble the Product
9
1. Loosen the screws in fan baffle and remove the fan baffle from the motor.
Description Part Number Quantity
Tapping screw 5610042000 4 pcs
Fan baffle 3127502000
Replace the PCBA
10
Altri manuali per CS1400E
5
Indice
Altri manuali EGO Motosega
EGO
EGO CS1600-FC Manuale utente
EGO
EGO CS1400E Manuale utente
EGO
EGO CS1400E Manuale utente
EGO
EGO Power+ CS1800-FC Manuale utente
EGO
EGO Power+ CS1401E Manuale utente
EGO
EGO PSA1000 Manuale utente
EGO
EGO CS1600E Manuale utente
EGO
EGO CS1400E Manuale utente
EGO
EGO CS1800E Manuale utente
EGO
EGO Power+ CS1600 Manuale utente
EGO
EGO Power+ CS1604 Manuale utente
EGO
EGO POWER+ CSX3000 Manuale utente
EGO
EGO CS1610E Manuale utente
EGO
EGO Power+ CS1800 Manuale utente
EGO
EGO AC1000 Manuale utente
EGO
EGO POWER+ CSX3000 Manuale utente
EGO
EGO CS1400E Manuale utente
EGO
EGO Power+ CSX3002 Manuale utente
EGO
EGO CS1400 Manuale utente
EGO
EGO CS1400-FC Manuale utente
