EI 175 Manuale utente

Instruction Leaflet

EI 175/176 Strobe and Vibration Smoke Alarm System for the deaf and hard of hearing

Important: Read all instructions before installation. This

leaflet must be left with the end user after installation.

Introduction

This leaflet describes the installation of the EI 175 and EI

176 Systems. If the system is not being used for some time the

control panel power switch must be off to prevent the battery

from being totally depleted and possibly damaged.

Do not turn on until it is fully wired.

The systems consist of:-

EI 175 System EI 176 System

Smoke Alarm EI 100CD Smoke Alarm EI 105CD

(9V ionisation) (9V optical)

Control Panel EI 173 Control Panel EI 173

(with built-in strobe) (with built-in strobe)

Vibration Pad EI 174 Vibration Pad EI 174

The entire system is powered from the AC mains through a

low voltage transformer. In the event of a mains failure the re-

chargeable battery in the control panel is capable of powering

the total system, including up to 12 interconnected smoke

alarms for one week, followed by at least four minutes alarm.

1. Location and Installation

The Control Panel should normally be fixed such that the in-

ternal strobe light can be seen from the bed and the vibration

pad can be placed under the pillow or mattress. It has to be

powered from the mains (230 VAC), so a suitable power point

or junction box must be available to which it can be perma-

nently connected. The Smoke Alarm must be located as de-

scribed in the Smoke Alarm instructions supplied. Cable (10

m) is supplied to connect between the Control Panel and the

smoke alarm. This can be extended up to 50 m (20 ohms

max.) with suitable low voltage cable if required. The smoke

alarm supplied with the system may be interconnected with

other EI 9 Volt interconnect smoke alarms (EI 100C /105C

/103C only), up to a maximum of 12 smoke alarms in total.

Many dwellings require more than one smoke alarm for mini-

mum protection. See the smoke alarm instruction leaflet for

detailed advice on, location, maintenance etc.

Control Panel

The Control Panel should be permanently fixed to the wall

using the screws and plastic plugs enclosed. The screws

should be spaced 114 mm (4.5 in) vertically apart. The top

screw will be 27 mm (1.1 in) below the top surface of the con-

trol panel when installed. The screws (large heads) should be

screwed into the wall leaving a gap of approximately 4 mm

(0.15 in) under the head. Fit the keyhole slots on the back of

the control panel over the screw heads and slide the panel

down vertically into position.

The mains adaptor can be plugged into a socket. The socket

must not be used for any other equipment and it must always

be switched on.

It is preferable to permanently wire the unit into a mains junc-

tion box. Wire according to the following instructions.

Warning: First remove the power to the circuit at the distri-

bution board. If you are in any doubt about how to do this, get

help from a qualified electrician.

Connecting to mains junction box.

The mains lead wires are colour coded as follows:

brown: live

blue: neutral

The wire which is coloured blue must be connected to the

terminal/wire which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to the

terminal/wire which is marked with the letter L or coloured red.

The apparatus is not to be earthed, so no connection is to be

made to terminals or wires marked with the letter E, the sym-

bol or coloured green or green and yellow.

Bring the low voltage wiring to where the smoke alarm is to

be located. Route all wires neatly and securely along the walls

and ceilings.

Note: Turning off the power switch on the Control Panel

does not switch off the apparatus from the supply mains. The

switch removes the AC and battery power from the Control

(or EI 105CD - optical)

STROBE

VIBRATION PAD EI 174

9V SMOKE ALARM EI 100CD - IONISATION

(With rechargeable battery

for one week standby)

CONTROL PANEL EI 173

Professional

Panel, but the mains transformer remains connected to the

supply mains.

Vibration Pad

Plug the vibration pad into its locking socket on the control

panel. Place the vibration pad under the pillow or mattress. It is

important that the person in the bed can feel the vibration -

check it is sufficient to wake a person by lying on the bed and

pressing the test button on the control panel - see also

“Testing your system”. Some mattresses may not transmit

sufficient vibration and in these cases it should be fitted under

the pillow. Note: During testing, or in an actual alarm situation,

the pad pulses on and off for greater effect on sleepers.

Smoke Alarm

1. Choose the smoke alarm mounting position following the

siting instructions in the smoke alarm leaflet and screw it into

position.

2. Connect the red (remove the small piece of insulating tape

first), yellow blue and black wires from the control panel EI 173

to the terminals marked “R”, “Y”, “BL” and “BK” respectively,

as shown in figure 1.

2. Interconnecting Smoke Alarms

A maximum of eleven EI 100C/105C/103C nine volt

smoke/heat alarms may be interconnected to the EI 100CD or

EI 105CD Master Smoke Alarm. A maximum of 250 metres

(820 feet) of signal/alarm cable can be used, (maximum resis-

tance 50 ohm). Use only one Master Smoke Alarm per sys-

tem.

Warning: Do not connect these Master Smoke Alarms to

any other type of EI alarm, or to any other model produced by

another manufacturer. Doing this may damage the alarms and

could result in a shock or fire hazard.

When one alarm senses fire all interconnected units will

sound and the control panel will turn on the strobe light and vi-

bration pad. The wiring between the smoke alarms requires

three cores, two for power and one for interconnect, as shown

in figure 2. (Four core signal/alarm cable is suitable for this and

the wiring colours illustrated in figure 2 assume this is being

used). The master smoke alarm unit is connected to the con-

trol panel as described above. Then all the rest of the units be-

ing interconnected are wired to this master unit, as shown in

figure 2.

On the second unit cut off the battery snaps and connect the

battery wires to a two-way terminal block (not supplied). Con-

nect the red and black power leads from the master unit to the

other side of this terminal block. Connect the “BL” terminal

from the master unit to the number 1 terminal on the second

unit, using the blue core wire. Note the yellow wire from the

control panel only goes to the master unit - it is not connected

to any of the other units. Wire the third and subsequent units,

up to a maximum of twelve, in the same way.

3. Testing your System

After Installation

1. Plug in the control panel mains adaptor (or turn on the AC

mains if it is connected to a junction box). Slide the power

switch on the side of the control panel to the “on” position.

Check the continuous green light on the control panel cover is

visible. The red light behind the the test button on the smoke

alarm will flash every 40 seconds to show the unit is receiving

power.

2. Press the test button on the smoke alarm. The smoke

alarm should sound and the red light behind the button will

flash every second. After about 4 seconds the control panel

will turn on the strobe light and the vibration pad. Two people

may be needed for this test. Interconnected smoke alarms,

where present, must also be tested.

3. Press the control panel test button. Check the vibration

pad is on and that the strobe is flashing.

Daily & Weekly Testing

We recommend that you test your system weekly by press-

ing all the smoke alarm test buttons and checking that the vi-

bration pad and strobe light are operating. Also check at the

same time that the green power light is visible on the control

panel and that the red lights on all the smoke alarms flash ev-

ery 40 seconds.

Check daily that the vibration pad is in its correct position by

pressing the test button on the control panel.

Periodic Testing of Rechargeable Battery

The rechargeable battery takes about 20 hours to charge

from the control panel when it is first powered up. The panel

then maintains it in the fully charged state by continuous trickle

charge. In the event of a mains failure, the battery will power

the system, including up to 12 interconnected smoke alarms,

in standby for a week followed by at least 4 minutes alarm.

When the mains fails, the green light is extinguished and the

red light flashes rapidly on the control panel to indicate it is on

RED TO RED BATTERY CONNECTOR

REMOVED

YELLOW WIRE

NOT CONNECTED

4 CORE WIRE

TO CONTROL PANEL EI173

SMOKE ALARM EI100C/EI105C

BLUE TO TERMINAL 1

TERMINAL BLOCK

(NOT SUPPLIED)

BLACK TO BLACK

RED R

YELLOW

BLUE

BLACK

TO CONTROL PANEL

Control Panel connection to Smoke

Alarm

Fig 1.

Interconnecting Smoke Alarms

Fig 2.

battery power. If the battery is starting to be fully depleted the

red light will go off to indicate the system is totally unpowered.

The battery will last 5 years in normal use provided it is not

exposed to extremes of temperature for prolonged periods, or

fully discharged/charged a large number of times.

We recommend that the functioning of the rechargeable bat-

tery is checked at least yearly as follows:

(i) Ensure the control panel has been mains powered for at

least the previous 20 hours for the battery to charge.

(ii) Turn off the mains power to the control panel by unplug-

ging, or switching off the circuit at the distribution board.

Check that the green light goes off and the red light starts to

flash on the control panel.

(iii) Press the control panel test button for 20 seconds and

check the strobe flashes brightly and that the pad vibrates

strongly. Check that the red light continues to flash while the

test button is pressed. (Cover the strobe light with card to stop

this dazzling you while looking for the red light). This red light

flashing indicates that the battery is satisfactory. If the red light

goes off, or if the strobe is weak, or if the vibration is weak the

battery will need to be replaced. Contact the nearest address

in this leaflet for advise about getting a replacement.

4. Troubleshooting

If the units fail any of the tests outlined above after installa-

tion, the system has probably been incorrectly wired and/or all

units are not connected. Check all wiring carefully. If the green

power light on the control panel is not on, check the power

switch on the control panel is on. Check the wiring to the mains

and that the mains is not off (e.g. due to a tripped circuit

breaker or fuse).

The Control Panel monitors the wiring to the vibration pad

and the master smoke alarm for faults as follows:

(i) If the vibration pad is removed or if its wiring is open circuit,

the control panel will flash the strobe.

(ii) If the wiring to the master smoke alarm is disconnected,

open circuited or short circuited, the control panel will turn on

the vibration pad and the strobe light.

There are no user serviceable parts in this unit. If it is thought

to be defective, it must be returned to the manufacturer for re-

pair or replacement (see “Product Guarantee” section).

5. Accessories and other Features

Control Panel “Aux. Output”

The auxiliary output turns on when the control panel is in

alarm and can supply up to 200 mA at 12 Volts (range 10 to 14

Volts). (Note: the positive terminal is the pin next to the

“Clock Input” socket). An Auxiliary Strobe EI 178 is available

and is supplied with 10 m of cable and a suitable plug. It can be

located, for example, where it is readily seen during the day

(e.g. downstairs hallway). An extra Vibration Pad EI 174 is

also available with 2 m of cable and a plug for connecting it to

the auxiliary socket.

Control panel “Clock Input” socket

A suitable alarm clock (witha5to24Volts AC or DC output -

electrically isolated from the mains supply) can be connected

to this input socket with a 3.5 mm mono jack plug. When the

alarm clock triggers, the vibration pad turns on to wake the

person, but the internal strobe or auxiliary output do not turn

on. This lets the user know it is a wake-up call and not a fire.

Therefore the user needs only one vibration pad under their

pillow or mattress.

Triggering Control Panel into Alarm Externally

A manual fire alarm switch (e.g. a glass break type) can be

used to get the control panel to turn on the vibration pad,

strobe light, and the smoke alarm horn.

This is done by connecting together electrically the red and

blue wires, from the control panel, by means of a switch or

volt-free relay isolated contacts. The wires from the switch can

be connected into the circuit at the terminal block of the master

smoke alarm EI 100CD or EI 105CD.

(Note: If you are using a manual fire alarm switch in conjuction with an EI Loca-

tor Switch EI159 you must put a 2.2K ohm resistor in series between the fire

alarm switch contacts and the interconnect blue, wire. This is to limit the current

to the EI159 unit).

Power Requirements

The typical currents at 230 VAC are

•Standby 10 mA

•Alarm 50 mA

6. Product Guarantee

EI Electronics guarantees this system for one year from the

date of purchase against any defects that are due to faulty ma-

terials or workmanship. This guarantee only applies to normal

conditions of use and service, and does not include damage

resulting from accident, neglect, misuse, unauthorised dis-

mantling, or contamination howsoever caused. This guaran-

tee excludes incidental and consequential damage. If this

system should become defective within the guarantee period,

it must be returned to the nearest address in this leaflet, care-

fully packaged, with the power switch on the control panel in

the off position, with the problem clearly stated along with

proof of the date of purchase. We shall at our discretion repair

or replace the unit. Do not interfere with the system or attempt

to tamper with it. This will invalidate the guarantee, but more

importantly may expose the user to shock or fire hazards.

This guarantee is in addition to your statutory rights as a con-

sumer.

Manufactured by EI Electronics.

Shannon Co. Clare Ireland.

P/N B12207

Questo manuale è adatto per i seguenti modelli

Altri manuali EI Sistema di sicurezza

EI Ei3024 Manuale utente

EI 3016 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente