EINHELL 42.572.37 Manuale utente
TE-CI 12 Li
Art.-Nr.: 42.572.37 I.-Nr.: 11029
7
GB Original operating instructions
Cordless Impact Driver
Anl_TE_CI_12_Li_SPK7.indb 1Anl_TE_CI_12_Li_SPK7.indb 1 21.11.2019 08:01:5521.11.2019 08:01:55
- 2 -
1
2 3
1
3
7
8
5
4
2
58
6
1.
2.
6
5
Anl_TE_CI_12_Li_SPK7.indb 2Anl_TE_CI_12_Li_SPK7.indb 2 21.11.2019 08:02:1721.11.2019 08:02:17
- 3 -
4 5
6
a
2
3
7
4
1
Anl_TE_CI_12_Li_SPK7.indb 3Anl_TE_CI_12_Li_SPK7.indb 3 21.11.2019 08:02:1821.11.2019 08:02:18
- 4 -
Anl_TE_CI_12_Li_SPK7.indb 4Anl_TE_CI_12_Li_SPK7.indb 4 21.11.2019 08:02:1921.11.2019 08:02:19
GB
- 5 -
Table of contents
1. Safety regulations
2. Layout and items supplied
3. Proper use
4. Technical data
5. Before starting the equipment
6. Operation
7. Cleaning, maintenance and ordering of spare parts
8. Disposal and recycling
9. Storage
10. Charger indicator
Anl_TE_CI_12_Li_SPK7.indb 5Anl_TE_CI_12_Li_SPK7.indb 5 21.11.2019 08:02:2021.11.2019 08:02:20
GB
- 6 -
Danger! - Read the operating instructions to reduce the risk of inquiry
Caution! Wear ear-muffs. The impact of noise can cause damage to hearing.
Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted
by the device can cause loss of sight.
Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on
wood and other materials. Never use the device to work on any materials containing asbestos!
Store the battery only in dry rooms with an ambient temperature of +10°C to +40°C. Place only charged
batteries in storage (charged at least 40%).
For use in dry rooms only.
Safety class II
Anl_TE_CI_12_Li_SPK7.indb 6Anl_TE_CI_12_Li_SPK7.indb 6 21.11.2019 08:02:2021.11.2019 08:02:20
GB
- 7 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well.We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fire and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
2. Layout and items supplied
2.1 Layout (Fig. 1)
1. Bit mount
2. Battery capacity indicator
3. Changeover switch
4. On/Offswitch
5. Battery
6. Charging unit
7. LED lamp
8. Pushlock button
2.2 Items supplied
Please check that the article is complete as
specified in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
• Cordless hammer screwdriver
• Battery charger
• Battery pack
• Original operating instructions
• Safety instructions
3. Proper use
The cordless hammer screwdriver is designed for
tightening and undoing screws.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse.The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Anl_TE_CI_12_Li_SPK7.indb 7Anl_TE_CI_12_Li_SPK7.indb 7 21.11.2019 08:02:2121.11.2019 08:02:21
GB
- 8 -
4. Technical data
Motor power supply: ................................12 V dC
Idling speed: ....................................0-2,400 min-1
Blow rate: ........................................0-3,600 min-1
Clockwise/counter-clockwise: ........................Yes
Bit mount: ................................... 1/4 “ (6.35 mm)
Battery charger output voltage: .............. 12 V DC
Battery charger output current: .......................3 A
Charging unit supply
voltage: ............................. 100-240 V~ 50-60 Hz
Charging time: ..........................................45 min.
Battery type: ...................................... Lithium-ion
Number of battery cells: ................................... 3
Battery capacitance: ................................. 2.0 Ah
Weight: .......................................................1.1 kg
Max. screw diameter: ................................. 6 mm
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
LpA sound pressure level ........................ 77 dB(A)
KpA uncertainty ............................................. 3 dB
LWA sound power level .......................... 88 dB(A)
KWA uncertainty .............................................3 dB
Wear ear-muffs.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Screwing without hammer action
Vibration emission value ah= 3.508 m/s2
K uncertainty = 1.5 m/s2
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specified value
in exceptional circumstances.
The specified vibration value can be used to
compare the equipment with other electric power
tools.
The specified vibration value can be used for initi-
al assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect wor-
king order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever ne-
cessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched offand times in which the tool is
switched on but operates without load).
5. Before starting the equipment
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery pack with the charger sup-
plied.
2. Only ever use screwdriver bits which are
suitable for the purpose and in faultless con-
dition.
3. Before you begin to screw in walls and ma-
sonry, check for concealed electric wiring,
gas pipes and water pipes.
Anl_TE_CI_12_Li_SPK7.indb 8Anl_TE_CI_12_Li_SPK7.indb 8 21.11.2019 08:02:2121.11.2019 08:02:21
GB
- 9 -
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(6) into the mains socket outlet.The green
LED will then begin to flash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will find a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
• voltage at the power socket
• whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
• the charger and charging adapter
• and the battery pack
to our customer service center.
6.2 Changeover switch (Fig. 4/Item 3)
The slide switch above the On/Offswitch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation.To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Offswitch is blocked.
6.3 On/Offswitch (Fig. 4 / Item 4)
Infinitely variable speed control is possible with
the On/Offswitch.The further you push the
switch, the higher the speed of the cordless
screwdriver.
To switch on:
Press the On/Offswitch (4).
To switch off:
Release the ON/OFF switch (4)
6.4 Battery capacity indicator (Fig. 5 – Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED is lit:
The battery is empty, recharge the battery.
6.5 LED lamp (Fig. 4/Item 7)
The LED lamp (7) can be used in poor lighting
conditions to illuminate the area where you want
to screw.The LED light (7) will come on automati-
cally as soon as you press the On/Offswitch (4).
6.6 Changing the bit (Fig. 6)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
Inserting the bit:
• Insert the bit into the bit mount (1) as far as
the stop while simultaneously pulling the slee-
ve on the bit mount (1) toward the bit.
• Release the sleeve again.
• Check that the bit is securely seated.
Removing the bit:
• Pull the sleeve on the bit mount (1) toward the
bit, hold it tight and remove the bit.
6.7 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw.
Anl_TE_CI_12_Li_SPK7.indb 9Anl_TE_CI_12_Li_SPK7.indb 9 21.11.2019 08:02:2121.11.2019 08:02:21
GB
- 10 -
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always remove the battery pack before making
adjustments to the equipment.
7.1 Cleaning
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
• We recommend that you clean the device
immediately each time you have finished
using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device.The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit.The raw
materials in this packaging can be reused or
recycled.The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse.The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.
9. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature.The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
Anl_TE_CI_12_Li_SPK7.indb 10Anl_TE_CI_12_Li_SPK7.indb 10 21.11.2019 08:02:2121.11.2019 08:02:21
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali EINHELL Avvitatore a impulsi
EINHELL
EINHELL CC-IW 450 Manuale utente
EINHELL
EINHELL CC-IW 950 Manuale utente
EINHELL
EINHELL CC-HS 12/1 Manuale utente
EINHELL
EINHELL TC-CI 12 Li Manuale utente
EINHELL
EINHELL CC-IW 950/1 Manuale utente
EINHELL
EINHELL CC-IW 450 Manuale utente
EINHELL
EINHELL 4510045 Manuale utente
EINHELL
EINHELL TP-CI 18 Li BL Manuale utente
EINHELL
EINHELL TE-CI 18/1 Li Manuale utente
