2
SAFETY INFORMATION
•Follow workshop health & safety rules,
regulations and conditions whenusing the
floor jack.
•This is alifting device only. Do not useit for
anything other than its intended purpose.
Load must be supported by proper rated
capacity jack stands underthe vehicle before
starting inspection or work. Do not overload.
Jack capacity is 3 tons.
•Use only on hard level surfaces.
•Never stand or place your body beneath the
load being lifted.
•Never attempt to exceed thelimits of the
floor jack. Applying excessive force to the tool
can overload the jack, decrease thelife and
increase the wear onthe jack.
•Lift only onareas of the vehicle as specified by
the vehicle manufacturer.
•Do not move or dolly the vehiclewhileit is on
the jack.
•Use genuine parts only. Unauthorized parts
may be dangerous and will void the warranty.
•Keep the floor jack cleanand in good working
order for best and safest performance.
•DO NOT use the floor jack for a task it is not
designed to perform.
•DO NOT use for aircraft purposes.
•DO NOT overreach. Keep proper footing and
balance at all times. Do not reach over or
across the product.
•DO NOT drop, throw or abuse the floor jack.
•Failure to heed these markings may result
in serious personal injury and/or property
damage.
WARNING!
•DO NOT use the floor jack if damaged or
thought to be faulty. Contact yourlocal service
agent.
PACKAGING CONTENT
DESCRIPTION QTY.
Floor Jack 1
Lower Handle 1
Upper Handle 1
O.I.P.M. 1
TOOLS NEEDED
•10 mm spanner / 3/8” spanner
•18 mm spanner / 11/16” spanner
•8mm hex key/ 5/16” hex key
BEFORE INSTALLATION
•Make sure all equipment is rated to the
appropriate capacity.
•Check damaged parts.Before using the tool,
any part that appears damaged should be
carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment and binding of
moving parts, any broken parts ormounting
fixtures; and any other condition that may
damaged should be properly repaired or
replaced by a qualified technician.
•Always use good quality hydraulic jack oil
when adding or replacing the oil in your
together. When filling theFloor Jack with oil,
do not permit dirt or any other substance to
enter the hydraulic system. (Refer Maintenance
of Page 3 for more details.)
•Make sure that all connections are secure.
•Consult the vehicle owner’s manual to
determine thelocation of lift points.
WARNING!
•Defective accessories can lead to personal
injury and material damage
INSTALLATION
(Refer “EXPLODED VIEW”)
CAUTION
· The Floor jack is heavy. Usecaution when
lifting out of box.
Assembly
•In the two piece handle assembly (37)
provided, assembletheupper sectioninto
the lower section, line up the holes, insert and
tighten the screw (38). Use a 10mm spanner /
3/8” spanner to tighten thescrew.
•Insert the bottom end of handleinto the top
of handle Socket (28) and securely tighten the
handle bolt (27) and washer. Ensure the handle
can turn freely. Usean18 mm spanner /11/16”
spanner to tighten the bolt.
•Turn the handle/release valve clockwise to the
closed position. Do not over tighten.
•Your floor jack is ready for use.
OPERATING INSTRUCTIONS
(Refer “EXPLODED VIEW”)
CAUTION
•Chock vehicle’s wheels to prevent rolling while
lifting.
•Use jack stands to support vehicle. Never work
around or under a vehicle supported only by
the Floor Jack.
•Watch for movement of vehicle or jack stands
as vehicle is lowered. If any movement occurs,
jack vehicle up and adjust jack stands properly.
•When not in use, make sure pressure is
released by turning HandleAssembly fully
counterclockwise. This will prolong the life of
the jack.
Lifting
•Twist the handle assembly clockwise to close
the pressure release valve.
•Position the jack underthespecified lift point.
