Ekwb EK-Quantum Vector FE RTX 3070 Manuale utente

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector FE RTX 3070

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process, to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 9

INSTALLING THE WATER BLOCK 9

PLACING THE BLOCK ON THE GRAPHICS CARD 9

ATTACHING THE BLOCK TO THE GRAPHICS CARD 10

CHECKING FOR CONTACT 10

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 11

INSTALLATION OF FITTINGS AND TUBING 11

CONNECTING THE D-RGB LED STRIP 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

BOX CONTENTS

4 mm

6 mm

8 mm

M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)

M2.5 Nut (2 pcs)

M2.5x6 AX1 Screw (13 pcs)

Allen Key 2.5 mm (1 pc)

Thermal Pad F 1.0 mm (4 pcs)

Thermal Grease (1 pc)

M2.5x8 AX1 Screw (2 pcs)

M2.5x4 AX1 Screw (16 pcs)

EK-Quantum Vector FE RTX 3070 PVC Washer M2.5 (16 pcs)

120 mm

16 mm

EK-Plug G1/4 (2 pcs)

Universal Mounting Mechanism – You may not need every

screw from this package.

- 5 -

WATER BLOCK DIMENSIONS

204.90 mm

193.40 mm

179.90 mm

97.90 mm

36.40 mm

65.40 mm

20.65 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

Technical Speciﬁcation:

Dimensions (LxHxW): 205 x 98 x 20.5 mm

D-RGB (Addressable RGB) Cable - Length: 500 mm

D-RGB LED Count: Plexi - 5

D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)

M4 x 10 DIN7984 SCREW

TOP PLATE

(PLEXI,ACETAL)

COLDPLATE

PLEXI INSERT

JE T PL AT E

TERMINAL O-RING

15 x 1 mm

M4 x 10 DIN7991 SCREW

M3.5 x 2.5 STANDOFF

EK BADGE

D-RGB LED STRIP

(PLEXI VERSION ONLY)

MAIN O-RING 116 x 2 mm

TERMINAL

(PLEXI,A CETAL)

M4 X 27

DIN7984

SCREW

STANDOUT

(NICKEL,BLACK ELOX)

M3.5 x 12.60

STANDOFF

M4 x 2.5

STANDOFF

- 7 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove the

stock cooler. Do not forget to unplug all the LED and fan connectors.

Pay attention to the following steps in order to install the EK-Quantum

Vector FE RTX 3070 water block onto the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers.

STEP 2

- 8 -

STEP 1

Your GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Replacement thermal pads:

4x Thermal Pad F 1.0mm – (120X16mm) EAN: 3830046996732

STEP 1

Thermal Pad F – 1.0 mm (120 x 16 mm)

CUTTING AND PLACING THERMAL PADS

120 mm

16 mm

1 mm

STEP 2

Once cut to size, thermal pads should be placed on the PCB,

as illustrated. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

Thermal Pad F 1.0mm

- 9 -

Thermal Grease

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the CPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 1

APPLYING THERMAL COMPOUND

For this Step, you will need:

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks.

Carefully position the water block with preinstalled standoffs on

the graphics card. During this process, make sure you have aligned

mounting holes of the PCB with holes of the water block (same

applies to other tops).

Pay attention not to use too much force when pressing the

block down to the PCB since chip dies are prone to cracking.

STEP 1

- 10 -

For this Step, you will need:

M 2.5 PVC Washer

(9 pcs)

M2.5 x 4 AX1

(11 pcs)

Phillips Head

Screwdriver

4 mm

STEP 2

M2.5 x 4 AX1 SCREW

M2.5 PVC WASHER

WITHOUT

PVC WASHER

WITHOUT

PVC WASHER

STEP 2

ATTACHING THE BLOCK TO THE GRAPHICS CARD

Use eleven (11) M2.5 X 4 AX1 screws and nine (9) M2.5 PVC

washers. Tighten the screws evenly using the Phillips head

screwdriver. EK recommends you start tightening the screws

around the GPU core first, and then continuing outward to prevent

the damage to the GPU.

CHECKING FOR CONTACT

If necessary, temporarily remove the water block to check for uniform

surface contact between the block and components. Pay special

attention to the VRM section of the graphics card. Check whether

the water block makes contact with the intended integrated circuit.

Then repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check

again or contact our support service at

https://www.ekwb.com/customer-support/.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-FC480 GTX Manuale

ekwb

ekwb EK-XTOP D5 Manuale

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manuale utente

ekwb

ekwb EK-FC580 DCII Manuale

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuale utente

ekwb

ekwb EK-FC5x0 GW GTX water block Manuale

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Guida

ekwb

ekwb EK-UNI RAD Manuale

ekwb

ekwb EK-MSI Z690 Carbon EK X Manuale utente

ekwb

ekwb Supremacy EVO Manuale utente

ekwb

ekwb EK-FC 780 GTX Lightning Manuale

ekwb

ekwb EK-FC R9-290X Original CSQ Manuale utente

ekwb

ekwb EK-FB ASUS X58 Guida

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Manuale utente

ekwb

ekwb EK-Annihilator Pro ILM Series Manuale utente

ekwb

ekwb EK-Classic GPU Water Block RTX 3080/3090... Manuale utente

ekwb

ekwb EK-FB MSI X370 XPower Monoblock Manuale utente

ekwb

ekwb GTX 1080 Ti Aorus Backplate Guida

ekwb

ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manuale utente

ekwb

ekwb EK-FC970 GTX TF5 TFX Series Manuale

ekwb

ekwb 3831109831335 Guida

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manuale utente

ekwb

ekwb EK-FC1080 GTX FTW Guida

ekwb

ekwb EK-FC R9 Nano Series Manuale

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-Quantum Vector FE RTX 3070 Manuale utente

Manuali Hardware per computer popolari di altre marche