Ekwb Velocity-AMD Manuale utente

USER GUIDE

2nd Revision, October 19th 2018

Velocity - AMD

CPU WATER BLOCK

This product is intended for installation only by expert users. Please

consult with a qualiﬁed technician for installation. Improper installation

may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products,

nor their installation. The following instructions are subject to change

without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure

and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

Please carefully read the manual before beginning with the

installation process!

Please remove your graphics card from the computer to assure

safest mounting process in order to prevent any possible damages

to your GPU and/or graphics card circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the rubber

O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended

for liquid cooling systems, and mandatory for nickel plated

water blocks!

Do not use pure distilled water! For best results EK recommends the

use of EK-CryoFuel coolants!

Make sure to thoroughly bleed air out of your water block, or you will

not reach optimal performance!

QUICK INSTALLATION GUIDE

- 3 -

INSTALLING THE WATER BLOCK 5

AMX AND FMX SOCKET MOTHERBOARDS 5

CONNECTING THE RGB LED STRIP (option) 9

CONNECTING THE RGB LED STRIP 9

CONNECTING THE DRGB LED STRIP 10

TABLE OF CONTENT

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY 4

WHAT IS ENCLOSED 4

SUPPORT AND SERVICE 11

SOCIAL MEDIA 11

- 4 -

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY

This CPU liquid cooling unit is pre-assembled for use with modern AMD

desktop socket type motherboards. By default (out of the box) this water

block supports the following CPU sockets:

- AMD® socket AMx and FMx

WHAT IS ENCLOSED

The following items are enclosed with each EK-Velocity water block:

- EK-Velocity AMD CPU water block.

- PreciseMount universal CPU mounting mechanism:

• M3 threaded thumb screws (4 pcs)

• LGA-2011 M3 threaded mounting studs (4 pcs)

• Springs (4 pcs)

• M3 threaded thumb nuts (4 pcs)

• Washers (4 pcs)

- EK-Velocity Backplate

• Backplate rubber gasket

• AMD® socket AMx and FMx

- Allen (hex) key 2.5mm

- Additional Inserts and Jet plates:

• Jet J2 (0.8mm* thick)

- Thermal Grizzly Hydronaut (EKWB 1.0g) thermal grease

- 5 -

AMx AND FMxSOCKET MOTHERBOARDS

STEP 1

Removing of the original plastic hold-down clamps and the

factory backplate:

Using Philips-head screwdriver remove the four UNC 6-32 screws

securing the original plastic hold-down clamps around the socket as

shown on the sketch. Remove the original AMD® backplate and the

hold-down clamps and store them away. See sketch for further part

identiﬁcation.

AMD® factory backplate

UNC 6-32

Screws

Hold-down

clamps

STEP 2

Preparing backplate rubber gasket

The enclosed rubber gasket is essential part of the backplate and

mounting system and must be used every time you install this water

block on your motherboard.

With AMD® Sockets you should use whole rubber

backplate including the inner core.

Outer part

Inner core

(removable)

STEP 1

STEP 2

INSTALLING THE WATER BLOCK

- 6 -

STEP 3

Install backplate rubber gasket and place metal backplate for AMD®

socket to the back of your motherboard RIBBED SIDE UP! (facing

away from the motherboard) Align the holes on the motherboard

with holes on rubber gasket and backplate.

Carefully rotate motherboard assembly with front side facing up

with one hand while holding the backplate and rubber in place with

the other hand.

AM4

Metal

Backplate

Rubber

gasket

Motherboard

STEP 3

STEP 4

Prepare the foil bag with mounting mechanism, which is enclosed

with the CPU water block delivery.

Install four (4) M3 thumb screws onto your motherboard. It is

mandatory to put 0.7mm plastic washer underneath each of the

M4 thumb screws. Tighten the screws to the metal backplate until

you reach the end of the thread. Using tools (such as pliers) is not

recommended.

Continue installation by following the instructions on

page 6 from STEP 2

M3 Thumb

Screw

PVC

washer

STEP 4

- 7 -

STEP 5

leaning the CPU: Wipe the CPU’s contact surface (by using non–

abrasive cloth or Q-tip, as shown on sample photo).

Applying thermal compound: On a clean IHS, apply a line of

thermal compound and spread it over the whole CPU heat spreader

(IHS) with a credit card or equivalent - see sample photo on left.

The layer of thermal compound must be thin and even in

thickness through the whole surface of the IHS. Too thick

application could lead to poor performance. This method

applies for Thermal Grizzly Hydronaut thermal compound

(3830046998477).

STEP 6

Align the water block over the mounting screws on the motherboard with

pre-installed CPU.

Before proceeding with the installation It is mandatory

to remove the protective foil from the backside of the

water block.

Place an enclosed compression spring and thumb nut over each M3

thumb screw. Start fastening two thumb nuts at a time, preferably in cross

pattern and do not tighten them fully until all of them are partially screwed

in. Then - using your ﬁngers only - screw in all four thumb nuts until you

reach the end of the thread.

STEP 6

Thumb nut

Coiled spring

Non-abrasive

cloth

IHS

STEP 5

- 8 -

STEP 7

Tighten the ﬁtting barbs in clockwise direction until the gasket underneath

is compressed.

The installation of the CPU water block is now complete.

Before proceeding with the installation It is mandatory

to remove the protective foil from the backside of the

water block.

With EK-Velocity series water blocks it is mandatory to use the port that

is nearest to the center of the water block as INLET port. Mixing the ports

may result in less than ideal thermal performance of the water block.

STEP 7

Fitting Ring

Fitting Barb

Inlet port

Outlet port

Outer part

Inner core

(removable)

STEP 8

- 9 -

CONNECTING THE RGB LED STRIP (option)

RGB LED Connector

CONNECTING THE RGB LED STRIP

STEP 1

Plug the 4-pin connector from Water block’s and Fan’s RGB LED light

to the RGB HEADER on the motherboard. The LED will work if the pin

layout on the header is as follows: +12V G R B.

Please ensure that the arrow indicated on the connector

is plugged into the +12V line as indicated on your

motherboard.

Failure to do so, will damage your motherboard or LED strip.

STEP 1

RGB Header

- 10 -

CONNECTING THE DRGB LED STRIP

STEP 1

Plug the 4-pin connector from Water block’s D-RGB LED light to the

DRGB HEADER on the motherboard. The LED will work if the pin

layout on the header is as follows: +5V, Digital, empty, Ground.

Please ensure that the arrow indicated on the connector is

plugged into the +5V line as indicated on your motherboard.

If you put LED Diode to the 12V RGB HEADER you can

damage the LEDs.

Failure to do so will damage your motherboard or LED strip.

Connector is the same on D-RGB and RGB versions,

but D-RGB version has 3 cables from connector to PCB;

RGB version has 4 cables. If you connect D-RGB led to

ordinary RGB header you can damage your motherboard

or LED strip.

D-RGB LED Connector

Connector is same on D-RGB and RGB version but

D-RGB version have 3 cables from connector to

Light. RGB version have 4 cables!!! If you connect

D-RGB led to ordinary RGB header you will damage

your motherboard or LED strip!!!!

STEP 1

D-RGB Header

RGB Header

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-Loop Fan FPT 120 FAN Manuale utente

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Guida

ekwb

ekwb EK-FC780 GTX Jetstream Manuale

ekwb

ekwb EK-FC R9-295X2 Manuale

ekwb

ekwb EK-FC 6970 V2 Manuale

ekwb

ekwb EK-PRO GPU WB RTX 30 0 Series Manuale utente

ekwb

ekwb EK-Vector Radeon VII Manuale utente

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Manuale utente

ekwb

ekwb EK-XTOP D5 Guida

ekwb

ekwb EK-FC670 GTX Series Manuale

ekwb

ekwb EK-FB ASUS R4BE Monoblock Manuale utente

ekwb

ekwb EK-FC980 GTX Guida

ekwb

ekwb EK-Quantum Velocity 2 Manuale utente

ekwb

ekwb EK-FB ASUS R5-E10 Guida

ekwb

ekwb EK-FB KIT GA X58 (UD7) Manuale

ekwb

ekwb EK-FC790 Guida

ekwb

ekwb EK-FB ASUS M6I Guida

ekwb

ekwb EK-FC980 GTX Classy KPE Backplate Guida

ekwb

ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox Manuale utente

ekwb

ekwb EK-FB GA AMD KIT Manuale

ekwb

ekwb EK-FC R9-390X TF5 Guida

ekwb

ekwb EK-SF3D Inflection Point EVO Manuale utente

ekwb

ekwb EK-Loop Modulus Series Manuale utente

ekwb

ekwb EK-Pro CPU Water Block SP5 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb Velocity-AMD Manuale utente

Manuali Hardware per computer popolari di altre marche