ekwb EK-PRO GPU RTX A6000 Manuale utente
USER GUIDE
GPU WATER BLOCK
EK-PRO
GPU WB RTX A6000
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING YOUR GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 8
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE BACKPLATE 12
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 12
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 13
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14
- 4 -
EK-PLUG G1/4 (2x)
3830046999153
Allen Key 2.5mm (1x) 8902
Allen Key 2mm (1x) 8901
120 mm
24 mm
BOX CONTENTS
Nut M2.5 (6x) 8506
Screw M2.5x4 ax1 (16x)
9047
EK-Loop Multi Allen Key (1x)
3830046996213
Screw M2.5x8 ax1 (10x) 8104A
Screw M3x6 DIN 7991 (2x) 9029
Thermal PAD F 1.0mm - (120x16mm)
(3x) 3830046996732
Screw M3x4 DIN7985 (2x)
8123
EK-TIM Ectotherm (1g) (1x)
3830046998446
Screw M2.5x10 ax1
(13x) 104344
Screw UNC 6/32x5 (1x) 8483
EK-Pro GPU WB RTX A6000 Ni +Inox
3831109847930
Washer POLYAMID M2.5 0.7mm
with self-adhesive tape (2x) 8627
Thermal PAD G 1.0mm - (120x24mm)
(3x) 3830046996770
120 mm
16 mm
Washer
POLYAMID M2.5 0.5mm
(16x) 8623
Screw M2.5x6 ax1 (13x)
9058
- 5 -
WATER BLOCK DIMENSIONS
96.9 mm
104.2 mm
134.2 mm
241.4 mm
252.8 mm
23.6 mm
134.2 mm
96.9 mm
70 mm
46.4 mm
75.4 mm
19.3 mm
- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Position EAN Description Quantity
1103686 054 - copper - RTX A6000 Pro
coldplate (Ni) 1
2101975 029 - top plexi – FC Quadro RTX
8000 Pro insert 1
3102549 Metal – Pro GPU WB jet 1
4102924 MS – Vector FE RTX Standoff
M3.5-M2.5x3 (Ni) 11
5103769 Top acetal – FC terminal direct
(2x G1-4) 1
6103713 054 – metal power adapter 1
7103687 054 – metal – RTX A6000 Pro top
inox 1
8103689 054 – alu – RTX A6000 backplate
(black elox) 1
9103090 Screw M3x6 ISO 14581 TX – inox 21
10 100006 Screw M4x27 DIN7984 3
11 5155 OR 15x1 EPDM50 (FC terminal) 2
12 5061 OR – 160x2 NBR70 1
13 102490 Brass – Pro GPU bracket standoff
M4-6/32x5 1
14 5167 OR 17x2 1
15 8483 ISO 7380 – UNC 6-32x5 1
16 100663 EK RGB Badge 1
17 8627 Washer POlYAMID M2.5 0.7mm 2
11
9
12
10
1
7
17
4
14
8
6
16
2
3
5
15
13
- 7 -
PREPARING YOUR GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove
the stock cooler. Do not forget to unplug all the LED and fan
connectors. Pay attention to the following steps in order to install
the EK-Pro GPU RTX A6000 water block onto the graphics card.
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 2
- 8 -
CUTTING AND PLACING THERMAL PADS
Your GPU water block comes with un-cuted thermal pads to cover all
the VRM components, such as COILs, MOSFETs, and drivers. Please
use 1.0mm thick thermal pads which should be placed on the PCB,
as illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal Pad F 1.0 mm
Thermal Grease
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
APPLYING THERMAL COMPOUND
For this Step, you will need:
- 9 -
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks. Carefully
position the water block with preinstalled standoffs on the graphics
card. During this process, make sure you have aligned mounting
holes of the PCB with holes of the water block.
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1
STEP 2
M2.5 x 4 AX1
SCREW
M2.5 PVC WASHER
STEP 2
To attach graphich card to waterblock use stock cross backplate.
Mount it with polyamind M2.5 pads and stock M2.5x4 screws.
- 10 -
STEP 3bSTEP 3a
STEP 3
Secure power cable with mounting it into included inox power
adapter.
STEP 3a
Stick the two included plastics pads (M3) on to inox power addapter
as shown on picture.
STEP 3b
Insert 8-pin power connector in to the inox adapter. Pads on the
power adapter must be alligned with openings in inox power
adapter.
Pay attention to the orietation of the latch on connector.
For this Step, you will need:
M3x6
SCREW
Screw M3x6 DIN 7991
(2x) 9029
Allen Key 2mm
(1x) 8901
STEP 3c
STEP 3c
Fasten a inox power adaptor to the water block with two (2) M3x6
screws. When power cables is installed there is needed a litlle bend
and twist of power cables in order to atteched power adaptor to
water block.
Indice
Altri manuali ekwb Scatola di raffreddamento
