ELCOM CLE-200 Manuale utente
Guidance
CLE-200
ELCOM-Türsprechanlagen
R
Hauskommunikation für Ihre Sicherheit
Zeichnungsnummer:
AN CLE-200
edition 04.04.2003
Code-Lock for mounting
description:
Technical Dates:
Signal tones:
Operating voltage: 12V AC or 15V DC
Power input: standby: ca. 10mA active: max. 70mA
Switching contacts: floating (max. 24V / 1A)
Key acknowledge: tüüt (0,2 sec)
input OK: tüüüüüüüüüüüüt (1sec)
input false: tüüt....tüüt....tüüt (6x)
Alarm: tüüt....tüüt....tüüt (60 sec)
The CLE-200 is a code lock system with two independent switching contacts, which are steered via different
codes (1…8-digit). The active duration may be adjusted individually between 1-99 seconds. Alternatively a
switch-mode can be realized, which switches on the contact after the first manual code input and switches it off
after the second manual code input. If incorrect codes are entered, then the code lock system blocks the
function after the fifth wrong input for 60 seconds and indicates this by an signal tone.
Each further wrong input again releases the blockage and the signal tone for further 60 seconds.
All attitudes of the code lock are made via the keyboard and are protected by a master code against
manipulations.
Wire attach:
Wire solve:
insert wire (massive wire
0,4-0,8mm)
operate orange latch-key
and pull wire out.
Ø
1 2
12V~
(max. 24V/1A)(max. 24V/1A)
21,5
3,5 +/-10%
Sealing foil
66,7
76,7
86,7
100
4
5,5 88
109
Guidance
CLE-200
ELCOM-Türsprechanlagen
R
Hauskommunikation für Ihre Sicherheit
Zeichnungsnummer:
AN CLE-200
edition 04.04.2003
Code-Lock for mounting
Programming:
Note:
Switchcode 1:
The codes must be selected in such a way, that these are assigned clearly. (Not allowed: Code1=1234
Code2=123)
If no switchcode is programmed (code programming mode is terminated with the key former input
of a code) the switching contact may be activated by pushing of the key .
In order to activate the switch mode, the switch term =0 seconds has to be adjusted. By pushing of the key ,
the current procedure may be aborted.
- push and hold key , additionally key , pushed and held for 3 seconds, until audio signal sounds.
- enter current mastercode - audio signal sounds.
- push key - .
- enter switchcode and push key -
without
audio signal sounds
audio signal sounds.
- push and hold key , additionally key , pushed and held for 3 seconds, until audio signal sounds.
- enter current mastercode - audio signal sounds.
- push key - audio signal sounds.
- enter switchcode and push key - audio signal sounds.
- push and hold key , additionally key , pushed and held for 3 seconds, until audio signal sounds.
- enter current mastercode - audio signal sounds.
- push key - audio signal sounds.
- enter switch trm in sec. (1-99 or 0) and push key - audio signal sounds.
- push and hold key , additionally key , pushed and held for 3 seconds, until audio signal sounds.
- enter current mastercode - audio signal sounds.
- push key - audio signal sounds.
- enter switch trm in sec. (1-99 or 0) and push key - audio signal sounds.
- push and hold key , additionally key , pushed and held for 3 seconds, until audio signal sounds.
- enter current mastercode - audio signal sounds.
- push key - audio signal sounds.
- enter new mastercode and push key - audio signal sounds.
- audio signal sounds
Switchcode 2:
Switchterm 1:
Switchterm 2:
Mastercode:
restore/backup Mastercode:
If your mastercode has been lost, you may backup to factory setting (789) and restore.
- switch off voltage supply.
- push and hold keys + + simultaneousely.
- restart voltage supply .
factory settings: current attitudes:
switchcode 1: ................................................
switchcode 2: ................................................
switch term 1: Sek. .........................................sec..
switch term 2: Sek. .........................................sec.
Mastercode: ................................................
123
456
3
3
789
Altri manuali ELCOM Serratura
