Eldes ESIM252 Manuale utente

GSM CONTROL SYSTEM

ESIM252

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from“ELDES

UAB”.“ELDES UAB”reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this

GSM CONTROL SYSTEM Esim252 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of

conformity may be consulted at www.eldes.lt

User Manual v1.0

Safety instructions

Please read and follow these safety guidelines and assembly instructions in order to maintain safety of operators and people around:

• GSM control system Esim252 (further referenced as the system) contains an integrated radio transceiver operating in GSM

850/900/1800/1900 MHz bands.

• Don’tusethesystemwhereitcaninterferewithotherdevicesandcauseanypotentialdanger.

• Don’tmountthesystemnexttomedicalequipmentordevices,iftheyrequireso.

• Don’tusethesysteminhazardousenvironment.

• Don’texposethesystemtohighhumidity,chemicalenvironmentormechanicalimpacts.

• Don’tattempttopersonallyrepairthesystem.

• Systemlabelisonthebottomsideofthedevice.

System Esim252 is a device mounted in limited access areas. Any system repairs must be done only by qualied, safety aware

personnel.

Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance

must not be done during stormy conditions.

The system must be powered by main 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply which must be

approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the

system, switching the terminals places does not have any aect.

AnyadditionaldeviceslinkedtothesystemEsim252(computer,sensors,relaysetc.)mustbeapprovedbyLSTEN60950-1

standard.

External power supply can be connected to AC mains only inside

installation room with automatic 2-pole circuit breaker capable of

disconnecting circuit in the event of short circuit or over-current

condition. Open circuit breaker must have a gap between con-

nections of more than 3mm and the disconnection current 5A.

FuseF1modelMINISMDC050F0.5ABlownfusecannotbereplacedbytheuserandthereplacementfuseshavetobeexactlythe

same as indicated by the manufacturer.

Thedeviceisfullyturnedobydisconnecting2-poleswitchodeviceoftheexternalpowersupplyoranyotherlinked

device that the system Esim252 is powered from.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

ESIM252

AC/DC

TheWEEE(WasteElectrical andElectronicEquipment)markingonthis productorits documentation indicates thatintheEU the

product must not be disposed of together with household waste.

If you use I security class computer for setting the parameters it must be connected to earth.

Limited Liability

The buyer must agree that the system will reduce

the risk of re, theft, burglary or other dangers but

does not guarantee against such events.

“ELDES UAB” will not take any responsibility regar-

ding personal, property or revenue loss while using

the system.

“ELDES UAB” responsibility according to local laws

doesnotexceedvalueofthepurchasedsystem.

“ELDES UAB” is not aliated with GSM operators

providing cellular services therefore is not respon-

sible for the quality of cellular services.

Manufacturer Warranty

The system carries a 24-month warranty by the ma-

nufacturer “ELDES UAB”.

Warranty period starts from the day the system has

been purchased by the end user. The warranty is

valid only if the system has been used as intended,

following all guidelines listed in the manual and

within specied operating conditions. Receipt with

purchase date must be kept as a proof.

The warranty is voided if the system has been

exposed to mechanical impacts, chemicals, high

humidity, uids, corrosive and hazardous environ-

ment or other force majeure factors.

Package Content:

The system Esim252................... 1 pcs

Esim252 user manual................. 1 pcs

GSM antenna ................................ 1 pcs

Fastening holders........................ 3 pcs

About User Manual

This document describes GSM control system

Esim252, its operation and installation.

It is very important to read User Manual before

start using the system.

A quick start guide is located in rst two chapters.

Chapter 3 and 4 describe additional system capa-

bilities.

CONTENT

1. General Information

1.1 Function .......................................................................................................4

1.2 Operation Description.............................................................................4

1.3 Technical Specications .........................................................................5

1.4 Connector Functionality.........................................................................5

1.5 Connection Circuit....................................................................................6

1.6 System Installation ...................................................................................7

2. System Pre-operation and the Main Control Commands

2.1 Selecting device language

and verication of SMS central number ...........................................8

2.2 Password Change .....................................................................................8

2.3 User Numbers.............................................................................................9

2.3.1 Saving or Changing Numbers ..............................................9

2.3.2 Verication of Saved Numbers.............................................9

2.3.3 Deletion of Saved Numbers. .................................................9

2.4 Date and Time Settings ..........................................................................9

3. Additional System Capabilities

3.1 Renaming Zones and Controlled Output...................................... 10

3.2 Enabling/Disabling Zones...................................................................10

3.3 Info on Status SMS................................................................................. 11

3.4 Blocking Unknown Numbers.............................................................11

3.5 Remote Microphone Listening .........................................................12

3.6 Managing C1 and C2 Controlled Outputs. Timer .......................12

3.7 SMS Message Delivery to Multiple Users .....................................12

3.8 Calling all users ......................................................................................13

3.9 Conguration for advanced users................................................... 14

3.9.1 Additional possibilities of conguring

   zones(inputs)alarmandrestore.......................................25

3.9.2 Additional possibilities of controlling and

   conguringcontrollerC1(relayoutput) ........................ 27

3.9.2.1 Settings of the output controlled by calls........27

3.9.2.2 Settings of the output controlled

by SMS messages .....................................................28

3.9.2.3 Output control settings by event time.............. 30

4. Appendix

4.1 Restoring Default Parameters. ..........................................................32

4.2 „ELDES Conguration Tool“ software .............................................32

4.2 Technical Support.................................................................................. 32

1. General Information

1.1 Function

ESIM252 is a micro controller based device intended to inform users about the alarm in automatic or security systems. In addition

it can control up to two electric appliances.

1.2 Operation Description

Description of factory default settings.

GSM control system ESIM252 operates over GSM network 24/7, i. e. it always reacts to the incoming signal.

In case any input is violated, the system sends an SMS message and/or calls to the preset user phone numbers. SMS message

with the name of the violated zone will continue to be sent until successful delivery to one of the users or until it is delivered to

all users. The system continues to call until one of the ve users answers the call, rejects the call or until the call is ended by the

GSMserviceprovider.Iftheuseranswersthecall,thesystemactivatesmicrophone(mustbeconnectedtoESIM252)forlistening

on what is happening in the secured premises. When using audio feature in case of input alarm or restore event the user will be

able to listen to particular sound record uploaded to the ESIM252 device memory. After the end of the sound record, the system

activates the microphone for listening on what is happening in the secured premises. After„hanging the phone“ or after the end

ofthecall(duration-1min.),thesystemwillreturntothepreviousstate.Please,refertoELDESCongurationToolsoftwareHelp

section for more details on audio feature.

Up to 2 electric appliances connected to ESIM252 can be controlled from a mobile phone. This feature allows to turn on/o hea-

ting, lighting, lift the gates, blinds etc.

The system ignores incoming calls from unknown phone numbers and SMS messages with wrong password.

List of other congurable system possibilities.

Input types Normallyopen(NO) Operational only when the signal is transmitted.

Normallyclosed(NC) Operational only when the signal is switched.

Ways of initiating an

event

Event when an input is

violated(Alarm)

Phonecallinitiatedand/orSMSisdeliveredtouser(-s)whenthesignalis

transmitted to an input.

Event when a zone is

restored(Restore)

Phonecallinitiatedand/orSMSisdeliveredtouser(-s)whenthepreviously

transmitted input signal disappears.

Impulse counting Input is considered as violated only if the number of the preset impulses in the

inputisexceeded.Max.valueis4294967295impulses.

Ways of notifying about

an event

SMS The ways of notifying users about events occurred in the particular input can be

carried out only SMS, only a phone call or a combination of both can be chosen.

Besides, any of the users can be assigned to be informed in case a particular

input is violated or restored or both. Various combinations of informing can be

assigned for each user and input.

When features SMS All and Call All are enabled, the system sends SMS messages

and rings to all preset users starting with User1 despite the fact that the call was

answered or rejected etc.

Examples: User NR1 wants to be informed by SMS in case input Z3 is violated,

but does not want to be informed when input Z3 is restored. User NR3 wants to

be informed by SMS and phone call in case input Z2 is violated, but wants to be

informed only by SMS in case of Z2 restore event.

Phone Call

Ways of controlling

outputs(relays)

Turning on/o by SMS

The outputs can be turned on/o by sending the command by SMS message.

You can turn on/o:

1. for a permanent status

2. for a set period

3. for a set hour

4. repeating turning on/o.

Turning on/o by a call

The outputs can be turned on/o by calling. You can turn on/o:

1. for a permanent status

2. for a set period

3.toggle(outputstatuschangesaftereachcall)

Automatic turning on at

the preset hour

Outputs can be turned on for a set period at a set hour.

E. g. the relay is turned on at 18:00 and it is on for 5 hours. After 5 hours it turns

o automatically notifying the user about that.

Event log Event log feature List of occurred events by date and time - zone alarm/restore, output on/o etc.

USER MANUAL ELDES ESIM252 V1.0 5

1.3 Technical Specications

Electrical and mechanical specications

Supply voltage 10-24V50Hz~200mAmax/10-24V 200mAmax

Current used in standby mode 50mAmax

GSM modem frequency 850/900/1800/1900 MHz

Numberof“low”level(negative)inputs 4

Numberof“high”level(positive)inputs 1

Allowable„low“level(negative)inputvalues Voltage: 0... 1.6V; current: -0.8... -0.4mA

Allowable„high“level(positive)inputvalues Voltage: 5... 50V; current: 0.17.... 1.7mA

Number of outputs 2

Output type Relay.Normallyopen(NO)

Relayoutputmaximumcommutatingvalues 24V 1A / 24V 50Hz ~0,5A

Dimensions 82x63x20mm

Operating temperature range -20…+55oC

(-30...+55oCwithlimitations)

1.4 Connector Functionality

ANT

GSM

MODEM

SIM

CARD

MIC

LED1

LED2

DEFAULT D1 D2

AC/DC

RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1

USB

Short explanation of the main units

GSM MODEM GSM network 850/900/1800/1900 MHz

modem

SIM CARD SIM card

LED Light-emitting diodes indicator

DEFAULT Connectors(D1andD2)forrestoring

default settings

ANT GSM antenna SMA type connector

USB Mini USB connector

F1 Fuse

Connector functionality

Labeling Explanation

AC/DC Power supply pins

RELAY1 Dryrelaycontact.Normallyopen(NO)

RELAY2 Dryrelaycontact.Normallyopen(NO)

COM Common pin

Z5 “Low” level input Z5

Z4 “Low“ level input Z4

Z3 “Low” level input Z3

Z2 “High”level input Z2

Z1 “Low” level input Z1

Picture 1

1.5 Connection Circuit

USEFUL INFORMATION

When choosing GSM provider, it is worth inquiring whether the service is used in security application assuring fast and reliable

SMS message delivery and phone call connection.

USEFUL INFORMATION

When choosing GSM cellular provider, it is worth inquiring whether the service is used in security application assuring fast and

reliable SMS message delivery and phone call connection.

Esim252 and alarm system COM must be connected.

Inputs Z1, Z3, Z4, Z5 are connected to alarm system outputs if outputs are implemented as open collector circuit or any other

circuit and if it commutes with COM.

It is also possible to connect Z1, Z3, Z4, Z5 inputs to, for instance, motion sensor or any other sensor as well as automatics device

provided the inputs are commuted with COM.

Input Z2 is commuted with a “high level” impulse. Impulse duration is >600ms.

Picture 2

Picture3 AC power supply connection circuit

AUX+AUX-

HIGH

LEVEL

Z1Z2Z3Z4Z5COMRELAY1 RELAY2AC/DC

PGM1

PGM3

PGM4

PGM5

PGM2

GSM Control System

ESIM252

Alarm system or other appliance

Fuse 500 mA

~230V 50Hz

AC/DC

~10-24V

Metal box

PE contact

LED indicators functionality

LED1 Indicates SIM card status

LED2 Indicates network status

LED1 status Meaning

OFF SIM card is working properly

ON SIM card error

LED2 status Meaning

OFF No network connection

Blinking 3 times per second Poor network connection

Blinking 1 time per second Medium network connection

ON Excellentnetworkconnection

USER MANUAL ELDES ESIM252 V1.0 7

1.6 System Installation

The system can be installed only in a metal or non-ammable plastic enclosure. If the metal enclosure and transformer is used it

isnecessarytogroundtheenclosureusingyellow/greencolourcable.Fortheconnectionof230Vtransformeruse3x0.75mm2

1 thread double isolated cable. The primary circuit of the transformer must be connected through 0.5A fuse. 230V power supply

cables cannot be grouped with low voltage cable group. For the connection of power supply and output connectors use 1 thread

2x0.75mm2cable. For the connection of input/output connectors use 0.50 mm21 thread cable.

1. Fastenthesystemintheboxusingfasteningholders.

2. PlaceSIMcardintheholderbutmakesurethatSIMcardPINcodeisdisabled.(PINcodecanbedisabledbyputtingSIMcard

intomobilephoneandfollowingpropermenus).SIMcardshouldnothaveanyremainingSMSmessages.

3. Connectthecircuitasshowning.No2.Powersupplycablesareconnectedlast).WhenconnectingEsim252toalarmsystem

power supply, usually the security system AUX output is used.

4. WhenACpowersupply(groundtransformer)isusedconnectaccordingtocircuitno.3.Inthiscaseyoudonotneedtocon-

nect any other power supplies.

5. The system will start in less than a minute. LED2 indicator should be blinking or be ON indicating connection to GSM.

Picture3 AC power supply connection circuit

2. System Pre-operation and

the Main Control Commands

VERY IMPORTANT!!!

Underscoresymbol‘_’inthismanualisusedtorepresentspace.WhenwritingSMSmessages,everyunderscoresymbolshouldbe

replaced by single space symbol. XXXX – means password. Do not leave any space at the beginning and the end of the message.

To set ESIM252 system parameters easier and quicker you can use the computer, USB cable or remote device conguration over

GPRS connection and conguration software„ELDES Conguration Tool“. For more details, please, refer to chapter 3.2.

2.1 Selecting device language and verication of SMS central number

The language in which the device communicates with the user can be chosen before changing factory default password. To change

thelanguageinthesystemthatisalreadyconguredresetdefaultsettingsasdescribedin3.1appendix.

Send SMS message with the required language

code to the number of the SIM card inserted in

Esim252.

E.g., if you want to set the English language send

the following SMS message: EN

30-60 seconds later you should get an SMS message:

„English language conrmed.“ Go to chapter 2.2 upon

reception of this message.

Otherwise check for network connection and call Esim252 system from your mobile and wait until the system drops the call. You

should get an SMS message asking to change default password. Otherwise check for network connection and change SMS central

number.

SMS central number is saved in SIM card, therefore if SIM card has been used to send SMS messages with a mobile phone,

thenyoudon’t’needtochangeSMScentralnumber.OftenSMScentralnumberisalreadysavedinSIMcardbycellular

operator.

Central number can be entered by sending SMS message:

XXXX – is a password. Default password is four zeros: 0000. SMS central number is provided by cellular network provider.

Example: 0000_SMS_+37069899992

Message should be sent to the number of SIM card which is placed into the system. If all went correct, the system will send a messa-

ge: SMS central number has been successfully changed to +37011111111

2.2 Password Change

All SMS commands start with a password, please memorize it. Manufacturer default password is

four zeros 0000, which is necessary to change.

Manufacturer default password can be changed by sending the following SMS message to

Esim252:

To replace your password, send the following SMS message:

XXXXisanyfourdigitnumberexceptfourzeros.

Non-numerical characters like dots, colons, spaces are not allowed. YYYY is the old system password. If you forgot the password,

default manufacturer password can be restored, see chapter 4.1 for more details.

ESIM 252

0000_

PSW_XXXX

0000_PSW_XXXX

YYYY_PSW_XXXX

Language Code

lithuanian LT

english EN

russian RU

Table of

possible

languages

ESIM 252

XXXX_SMS_+37011111111

USER MANUAL ELDES ESIM252 V1.0 9

2.3 User Numbers

The system Esim252 allows to pre-program up to ve dierent mobile numbers which will have access to and control the system.

NR1 is mandatory while others can be skipped. All numbers must be entered starting with international country code, e. g. national

code for Lithuania is 370, UK – 44. By default the system starts sending all messages and in the event of alarm starts calling on the

rst number, and if the rst call is unsuccessful, it immediately tries reaching subscriber No2 etc.

2.3.1 Saving or Changing Numbers

SendSMSmessagewiththefollowingtexttoEsim252:

Ones should be replaced with user numbers.

Numbersdon’thavetobe enteredinsequential orderright away.E.g. usercan enterrstand

fourth number by sending the following SMS message:

Or individually one number at a time:

Numbers can be changed same way as described above. New number will overwrite old one, the-

refore no erasing is necessary.

2.3.2 Verication of Saved Numbers

To inquire the system about pre-programmed numbers, send the following SMS message:

The system will reply with all pre-programmed numbers.

2.3.3 Deletion of Saved Numbers

To erase NR2-NR5, send the following SMS message:

E. g. XXXX_NR3:DEL

The system will not allow erasing rst number NR1. It can only be modied.

2.4 Date and Time Settings

It is important to set correct date and time so that the system can send reports at specied times.

Date and time can be set by sending the following format SMS message:

where MMMM means year; mn - month; dd - day; va - hour; mi - minutes

E. g. XXXX_2009.01.01_14:15

ESIM 252

XXXX_

NR1:370

11111111_

NR4:370

11111111

XXXX_NR1:37011111111_NR4:37011111111

XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_NR4:37011111111_

NR5:37011111111

ESIM 252

XXXX_

NR3:370

11111111

ESIM 252

XXXX_

HELPNR

ESIM 252

XXXX_

NR3:DEL

ESIM 252

XXXX_

2009.01.

01_14:15

XXXX_NR3:37011111111

XXXX_HELPNR

XXXX_NR2:DEL_NR3:DEL_NR4:DEL_NR5:DEL

XXXX_MMMM.mn.dd_va:mi

3. Additional System Capabilities

3.1 Renaming Input Alarm/Restore Texts & Оutput Нames

Manufacturer initially set the following input alarm/restore texts and output names:

inputZ1alarmtext-Zone1Alarm,restoretext-Restore1;inputZ2-Zone2Alarm,restoretext-Restore2;0inputZ3-Zone3Alarm,

restoretext-Restore3;inputZ4-Zone4Alarm,restoretext-Restore4;inputZ5-Zone5Alarm,restoretext-Restore5;outputC1

name - Controller1; output C2 name - Controller2

E. g. in case input Z1 is violated, the system sends SMS message with the text: Zone1

Input alarm text

InputalarmtextischangedbysendingthefollowingSMSmesaage:

E. G. XXXX_Z1:Intrusion though the door;Z2:Fire sensor alarm;

Textscanbechangedallatonceforallinputs,severalofthemoronebyone.Maximumtextforone

inputtextis24characters.Thespaceisequaltoonecharacter.Eachnewtextmustbefollowedbyasemi

colon.Assemicolonisusedforseparatingtextsfordierentinputs.Itcannotbeusedinthemiddleof

alarmtexts,itcanonlybeusedattheend.Textscannotbethesameascongurationandcontrolcom-

mands, such as - ON, OFF, STATUS etc.

Input restore text

If you want to be notied by an SMS message when a violated zone is restored Restore mode must be turned on.The mode is turned

on by sending a particular SMS command. Please refer to chapter 3.9 or conguration program.

InputrestoretextischangedbysendingthefollowingSMSmesaage:

Output name can be changed by sending the following SMS message:

x-outputnumber;possiblevalues1-C1 or 2 - C2.

Outputnamecannotbefollowedbyasemicolon.Youcannotchangeinputalarm/restoretextandout-

put names at the same time.

E. g. XXXX_C1:PUMP

3.2 Enabling/Disabling Inputs

NOTE

Manufacturer set all the inputs activated, i. e. in mode ON.

USEFUL INFORMATION

The inputs can be enabled/disabled together or separately one by one.

Enabling Input

Any input can be enabled by sending the following SMS message:

XXXX_Z1:NewAlarmText;Z2:NewAlarmText;Z3:NewAlarmText;Z4:NewAlarmText;Z5:NewAlarmText;

XXXX_ZR1:NewRestoreText;ZR2:NewRestoreText;ZR3:NewRestoreText;ZR4:NewRestoreT

ext;ZR5:NewRestoreText;

XXXX_Cx:NewControllerName

XXXX_Z1:ON;Z2:ON;Z3:ON;Z4:ON;Z5:ON;

ESIM 252

XXXX_Z1:

trespaced;

Z2:

triggered

re

detector;

ESIM 252

XXXX_C1:

PUMP

Altri manuali per ESIM252

Indice

Altri manuali Eldes Hardware per computer

Eldes

Eldes EW1 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente