ELECRAFT N-GEN Manuale utente
Elecraft • www.elecraft.com • 831-662-8345
ELECRAFT N-GEN WIDEBAND NOISE GENERATOR
Revision D, November 7, 2008
Copyright © 2008, Elecraft; All Rights Reserved
Introduction
The Elecraft N-gen is a wideband noise source that is useful for a variety of receiver alignment tasks. It can be used in
conjunction with a software program such as Spectrogram to align IF filters in the K2 or in other receivers. It can also be
used to align the RF stages in Elecraft XV Transverters or other HF, VHF, and UHF equipment.
Note: The N-gen does not generate repetitive pulse noise, so it cannot be used to test pulse-type I.F. noise blankers such as
the Elecraft KNB1 or KNB2.
Specifications
Power Requirement: 9V battery or external 12 to 15 volts DC
Current Consumption: Approximately 25 ma.
Excess noise output: Approximately 35 dB (typical; varies with characteristics of D2 )
Bandwidth output level: +/- 3 dB from 100 kHz to 500 MHz
Assembly
Perform an inventory of all parts in the kit (see Parts List on page 2).
Install R1 (200_), R2 (150_), R3 (1K_), R4 (47_), and R5 (560_) in the positions indicated on the PC board silkscreen.
CAUTION: Before handling semiconductors in the following steps (diodes and MAR-1 amplifier IC), put on an
anti-static wrist strap or touch a grounded metal surface often during assembly.
Install D1 and D4 (1N4148) in the indicated positions. The diodes must installed in the correct
direction. The banded end of the diode is to be inserted into the hole with the square pad. D1 and D4
are 1N4148 diodes and are very similar in appearance to D2 a 1N5235B. If necessary, use a
magnifying glass to identify the diodes.
Install zener diode D2 (1N5235B).
Install 0.01uF (103) mono caps at C1, C2; a 0.047uF (473) mono cap at C3; and a 10pF (10J or 100)
mono cap at C4.
Install the LED at D3. The longer lead goes to the square pad. Two locations are marked as D2 on the Rev A board. The
location in the upper right corner should have been designated as D3.
Install the MAR-1 at U1. Note that the MAR-1 has one lead cut at a slant. This is the input lead. Align this lead toward
the center of the board as indicated on the silkscreen. If the board has a hole in the center of the pattern for U1, fit the body of
U1 into the hole. Otherwise, just center U1 in the pattern so the leads reach the solder pads.
Install J1, J2, and SW1.
Install the battery holder. Use 4-40 x _ inch pan head machine screws, lock washers and nuts.
Install the 4 mounting feet in the corners on the underside of the PCB.
Page 2 of 2
Test
CAUTION: Whenever you use the N-gen with a transceiver, you must prevent accidental transmit, which could damage
parts on the N-gen. Disconnect all keying devices (key, paddle, microphone). Reduce the transceiver's power level to the
lowest possible. In the case of a K2, rotate POWER fully counter-clockwise.
Install a standard 9-volt battery into the battery holder.
If you plan to test the N-gen using a transceiver, disable transmit as described above.
Connect the N-gen to the antenna input of a receiver or transceiver.
Place SW1 in the “ON” position.
The LED should light and there should be a substantial increase in the noise output of the receiver.
Parts List
Note: Resistor color codes and typical capacitor markings are shown in parentheses.
R1, 200 ohms 1/4 watt (red, black, brown) R4, 47 ohms 1/4 watt (yellow, violet, black)
R2, 150 ohms 1/4 watt (brown, green, brown) R5, 560 ohms 1/4 watt (green, blue, brown)
R3, 1000 ohms 1/4 watt (brown, black, red)
D1, D4, 1N4148
C1, C2, .01uF mono ceramic (103) D2, 1N5235B
C3, .047uF mono ceramic (473) D3, Red LED
C4, 10 pF ceramic (10J or 100) U1, MAR-1 MMIC
S1, Miniature DPDT Switch (2) 4-40 pan-head machine screw
J1, 12 volt power connector (2) lock washer
J2, BNC output connector (2) 4-40 nut
J2, BNC output connector (4) rubber feet
N-gen PC board
Circuit Details
The schematic of the N-gen is shown above. Noise generated within Zener diode D2 is amplified by wideband monolithic
amp U1. U1 is internally biased to present a 50-ohm load at the output.
Indice
Altri manuali ELECRAFT Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
