ElectrIQ IQOOLSMART12HP-WiredCtrl Manuale utente
USER MANUAL
WIRED CONTROLLER
IQOOLSMART12HP-WiredCtrl
Read these instructions carefully and keep them safe for future
reference.
2
SAFETY WARNINGS
•Before attempting installation, the Installation Manual must be fully read and
understood.
•When choosing a suitable position for installation, consideration should be
made to avoid external influences which may damage the unit, shorten its life,
or make the unit unsafe. Places to avoid include:
1. Areas in the vicinity of flammable gasses.
2. Areas where the unit may be splashed by liquids or oils.
3. Areas likely to experience extremes of temperature.
4. Areas exposed to high levels of electromagnetic radiation.
5. Any place with high levels of humidity.
•This unit should be installed by a competent person. If unsure, professional
advice should be sought.
•Do not operate this device with wet hands or allow it to come into contact with
water. An electric shock or short circuit may occur.
•Do not attempt to modify or repair the unit. This must only be attempted by a
qualified engineer under the instruction of the manufacturer.
•Ensure that the power supply is disconnected from the unit before attempting
to open the shell.
•Ensure the interconnecting cables are suitably rated for the application and that
they are routed in a way to prevent damage during installation and use.
•This unit is only designed for use with the air conditioners listed. Do not attempt
installation with any other equipment without confirmation from the
manufacturer.
•Ensure that any fixings used to wall mount the unit are suitable for the type of
wall.
•Before drilling holes, care should be taken to avoid any hidden pipework or
cables. If in doubt professional advice should be sought.
•Maintenance and repair of this product should only be carried out by a qualified
professional.
•Keep this manual safe for future reference or for use by a third party.
•The correct use of this product is detailed in this manual. Failure to follow the
instructions may result in damage or injury.
•All installation and service carried out on the appliance must conform to the
corresponding local standards, laws and regulations.
•Due to continuous product development, the product may vary slightly from the
illustrations provided.
•The length of the supplied cable is 2.5m if this needs to be extended, it must be
done so by a qualified engineer or a suitably competent person.
3
INSTALLATION
Use the screws provided (M4x25) to fix the controller backing plate onto the
wall, ensuring that it is securely connected before proceeding. Depending on the
type of wall, suitable fixings should be purchased.
NOTE: Do not overtighten the screws, as this may cause the backing plate to
distort or break.
Remove the wired controller from the backing plate using
a flat headed screwdriver in the gap between the backing
plate and the controller. Once the two parts are
separated, the remainder can be unclipped.
Pass the signal wire through the opening in the rear of the
backing plate, ensuring it is positioned so it will not be
trapped or damaged during installation. Allow enough cable
to pass through for ease of installation and future
maintenance.
Connect the signal wire between the wired controller
and the air conditioner. The cable with the connector
for the controller is fixed to the rear of the air
conditioner.
If the signal cable provided is too short it can
be replaced with suitable 5-core shielded
cable up to a maximum length of 20m.
4
CONTROL PANEL
DISPLAY
Standard wire controller
Error
indicator
Cooling
Mode
Dehumidify Mode Heating Mode
Fan Mode
Fan Speed
Sleep
Swing
Room Temperature
Timer
display
Clock
Desired
Temperature
Power
Mode
Timer
Fan
speed
Sleep
mode
Clock
Enter
Swing
Temperature
Time
5
OPERATION
POWER BUTTON:
Press to turn the air conditioner ON and OFF
MODE BUTTON:
While the air conditioner is operating press the mode button to change between the 4
modes. The current mode will be shown on the display.
Heating Mode Dehumidify Mode
Fan Mode Cooling Mode
TEMP AND BUTTONS
These buttons are used to increase or decrease the desired room temperature. Both the
current temperature and the desired temperature are shown on the display.
CLOCK BUTTON
Press the clock button to set the current time. Use the TIME and buttons to adjust the
time. After a few seconds of been set, the clock will start to operate.
TIMER BUTTON
Use to set the desired time for the unit to turn on or off. Please note the time must have been
set on the unit before the timer can be used.
ON TIMER –The timer will turn on the unit automatically after the time set has elapsed.
1. With the unit is standby, press the TIMER button so that the ON TIMER symbol is
shown on the display.
2. Use the TIME and buttons to set the desired start time.
3. Once the set time has elapsed, the unit will turn on automatically with the settings
that were operating before the unit was turned off.
OFF TIMER –The timer will turn off the unit automatically at the set time.
1. While the unit is running press the TIMER button so that the OFF TIMER symbol is
shown on the display.
2. Use the TIME and buttons to set the desired stop time.
3. Once the set time has elapsed, the unit will turn off.
FAN BUTTON
The fan speed button is only available in cooling, heating and fan modes. Press the fan speed
button to change between the available fan speeds.
SWING BUTTON
Press the Swing button to activate the swing function on the air conditioner. Press the button
again to turn off swing mode.
SLEEP BUTTON
Press sleep to enter the unit into sleep mode. Sleep mode will operate the same as described
in the air conditioner’s manual. The unit will run at the lowest fan speed. To exit sleep mode,
press any button.
6
DISASSEMBLY
Disassembly is the reverse of installation. Make sure that the mains power has been
disconnected to avoid risk of injury.
Remove the wired controller from the backing plate using a flat head screwdriver in the gap
between the backing plate and the controller. Once the two parts are separated, the
remainder can be unclipped.
Disconnect the signal wires from the rear of the wired controller.
Pass the signal wire through the opening in the rear of the backing plate, ensuring they are
not damaged during removal.
electriQ UK Support.
www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling the service line.
If the unit still fails to operate call: 0871 620 1057 or complete the online form
Office hours: 9AM - 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA
PRODUCT DISPOSAL
Do not dispose this product as unsorted municipal waste. Collection of such waste must be
handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any
old electrical equipment to participating civic amenity sites run by their
local councils. Please remember that this equipment will be further
handled during the recycling process, so please be considerate when
depositing your equipment. Please contact the local council for details of
your local household waste recycling centres.
Indice
Altri manuali ElectrIQ Controllori
