Electroconcept MATRIX 430 Manuale utente

MATRIX 430

Instruction manual

Thank you for purchasing this product.

Please carefully read this manual before using this

spotlight

Responsibility :

On no account the Electroconcept company shall be held responsible for any damages of any nature

whatsoever, notably the operating loss, destruction of consumables (tape, disc, CD) or any other

financial loss resulting from the use or the impossibility to use your equipment. n addition

Electroconcept shall not be held responsible for damages due to an improper use of this product.

Warranty :

Electroconcept products have a 2 years manufacturer warranty. The equipment shall be returned

prepaid (at the customer's own expense). Any freight collect will be refused. The equipment shall be

returned in its original packaging. The equipment's restitution will be at our own expense.

Are excluded from warranty: damages due to fault, negligence, lack of maintenance by the user

(broken, burnt, heated, wet, sandy...etc devices), already installed devices of which the failure would

originate from an improper installation or use by the customer.

This manual is an integral part of this product, you will need to keep it during all of

your product shelf-life. In the event of cession of your product to a third party, you

must also give this manual to this third party.

TABLE OF CONTENTS

1. Safety instructions

2. Technical specifications

3. Spotlight starting up

1. Access to main functions

2. DMX wiring

4. DMX control channels and values

5. Troubleshooting

6. Cleaning

1. Safety instructions

Please carefully read these instructions as they include

valuable information for installation, o eration and

maintenance of this device.

Warning

Keep this manual for future consultations. f you resell your spotlight to an other

individual, make sure to also give him this manual.

Unpack and carefully check that the spotlight didn’t take any damages during the transport

before using it.

Before any connection, make sure that both the voltage and the frequency of your power

source match your spotlight specifications.

Check your device as well as your equipment’s grounding.

This device is only meant for indoor use ; protect it from heat and humidity (allowed

ambient temperature from 10 to 40°C).

The spotlight must be set up in a ventilated area, at least 50cm away from any adjacent

surface. Check that no ventilation hole is blocked.

Unplug the spotlight’s power source before any maintenance or handling operation.

Only replace the fuse by a fuse of the same type.

n order to avoid any fire hazard, check for any flammable source nearby.

Use safety cables to secure the spotlight. Hold the spotlight only by its carrying handles to

avoid degradation and risk of injury.

Switch off the power and let the spotlight cool down for about 15 minutes before transport,

for the spotlight’s surface may be hot still.

n the event of a serious functioning problem, stop immediately to use the device. Do no

ever try to repair the device by yourself. Repairs made by unqualified individuals may

cause damages or malfunctions. Contact the nearest approved technical support center.

Always use spare parts of the same type.

Do no connect the spotlight to any dimmer or power pack.

Do no open the device during its operation, the high voltage may cause a lethal electrical

shock.

n order to prevent or reduce risks of electrical shock or fire, do not expose the device to

rain or humidity.

Do not ever touch the led with your bare fingers after use to avoid serious injuries, for the

led may be very hot still.

Do not start the spotlight without led to avoid degradation of the box..

Re lace the box and the lenses if they are visually damaged (for exam le cracks or

dee cuts during trans ort or handling). This is essential.

Do not look straight at the light going out of led when the spotlight is switched on.

n order to prevent any risks of electrical shock you must not remove the cover. There is

no useful part for the user inside. Refer the repair to qualified personnel.

Installation

The spotlight must be attached via its screw holes to the support with help of the provided

hook. Always make sure the spotlight is firmly attached to avoid vibrations and sliding during

the operation.. Always make sure the structure to which the spotlight is attached is secured and

able to bear 10 times the projector’s weight.

. Technical specifications.

This device does not produce radio interference. This device meets

European and French requirements. Compliance has been established, and

statements and respective documents have been registered by the

manufacturer. This device has been made for indoor decorative lighting

effects.

Power supply : AC 220-250V 50/60Hz (fusible 3A

Input / Output : Power Con (blue / gray

Power: 150 W

Lamp : 4 LEDs RGW 30W

Colors: RGB colors + White

Dimmer PWM :Depth of 12 bits by color

DMX : DMX 512 wired ou DMX HF (Rev A ou Rev B

Beam: 24 degrees

Weight/Dimensions: 2,5 Kg / 450 x120 x185 mm

Operating mode :

-DMX control from 1 to 23 channels. Stand-Alone mode with built-in microphone / Stand-Alone mode

with Auto mode/ Master/Slave mode

3. spotlight starting up

3.1. Access to main functions :

Control anel:

”MENU“ “▼ ” “▲” ”ENTER”

Press the “MENU” button to access to the mode selection, then « ▼ » or « ▲ » to select the mode.

Confirm the selected mode with « ENTER » .

Browse through the sub-menu with « ENTER » and « ▼ » or « ▲ » to modify the value . To confirm or

to go back, “MENU” button .

4 Operating modes are available : DMX Control , Master mode and Slave mode, Macro mode.

DMX Mode : D---

D001 : DMX address

Hn16 : Selection of DMX mode (number of channels from 1 to 21

Fixed color mode : C---

r001 :Red Color -> level from 0 to 255

g001 : Green Color -> level from 0 to 255

B001 : Blue Color -> level from 0 to 255

u001 : White Color -> level from 0 to 255

Master Program Mode : P---

P-01 : selection of internal program. They are intended to control 3 slave projectors

S001 : Speed -> level from 0 slow to 127 fast

SOon : Sensitive to sound -> On or oF

S la ve Mode : S---

I D-1 : Positioning of the Slave spotlight from 0 to 3 (cf 4,1

FL-0 : Layout of spotlight and Leds. Leave it to 0 for synchronous effects. Modify to change

the leds’ reaction (right flip, up flip etc...

In Slave mode the DMX cable must be connected between the products (no Master/Slave mode in

Macro Mode : M---

M001 : Used Macro -> from 0 to 31 , from 16 to 31 are fixed pixels (for example to manage

giant letters

S001 : Speed -> level from 0 slow to 127 fast d

r001 : Red Color -> level from 0 to 255

G001 : Green Color -> level from 0 to 255

B001 : Blue Color -> level from 0 to 255

U001 : White Color -> level from 0 to 255

r001 : Red Background Color -> level from 0 to 255

g001 : Green Background Color -> level from 0 to 255

B001 : Blue Background Color -> level from 0 to 255

u001 : White Background Color -> level from 0 to 255

SOon : Sensitive to sound -> On or oF

System Menu : SYST

I D-1 : Positioning of the Master spotlight from 0 to 3 in Master or DMX mode.

G-of : Gamma correction mode on the dimmer On or OFF

FL-0 : Layout of spotlight and Leds. Leave it to 0 for synchronous effects. Modify to change

the leds’ reaction.

3.2 DMX wiring

This product uses 3-pin XRL connectors for the DMX512 connection:

Pin 1 : Ground , Pin 2 : Data (-), Pin 3 : Data (+).

Example : connection between different fixtures in Master/Slave mode:

All fixtures must be at the same DMX address, the 1rst projector in Automatic or Sound mode,

following spotlights in DMX mode at the same address of the Master spotlight.

NB : in order to reduce signal errors, think of using a plug a the end of your DMX link.

4.DMX Values Table :

Mode 1 Channel

DMX Channel Description

1 Dimmer in White Blinder Mode

Mode 4 Channels

DMX Channel Description

1 Red Level from 0 to 255

2 Green Level from 0 to 255

3 Blue Level from 0 to 255

4 White Level from 0 to 255

Mode 6 Channels

DMX Channel Description

1 General Dimmer

2 Strobe 0 → 0FF : 1 → 255 From slow to fast

3 Red Level from 0 to 255

4 Green Level from 0 to 255

5 Blue Level from 0 to 255

6 White Level from 0 to 255

Mode 9 Channels

DMX Channel Description

1 General Dimmer

2 Strobe 0 → 0FF : 1 → 255 From slow to fast

3 Red Level from 0 to 255

4 Green Level from 0 to 255

5 Blue Level from 0 to 255

6 White Level from 0 to 255

7 Program 0 → Off : 1 → 255 Program (see programs table)

8 Program speed 0 → 127 slow to fast following the program’s course

128 → 255 slow to fast following the program’s counter-course

9 Palette 0 → 31 , the color program is the RGBW components of channels 3-4-5-6.

with 4 repetitions of the color pixel

RGBW Palette: 0→15 : 1 pixel over 2

RGBW Palette: 16 → 31 : 1 pixel over 4

RGBW Palette: 32 → 47 : 1 pixel over8

RGBW Palette: 48 → 63 : 1 pixel over 16

Palette Channel of 64 → 255 : 12 palettes of preset colors

Palette 1: 64 → 79 ,Palette 2: 80 → 95 ,Palette 3: 96 → 111 ,

Palette 4: 112 → 127 ,Palette 5: 128 → 143 ,Palette 6: 144 → 159 ,

Palette 7: 160 → 175 ,Palette 8: 176 → 191 ,Palette 9: 192 → 207 ,

Palette 10: 207 → 223 ,Palette 11: 224 → 239 ,Palette 12: 240 → 255

If the program is set to 0 with a clipped palette, the spotlight switches to Blinder mode.

Mode 13 Channels

DMX Channel Description

1 General Dimmer

2 Strobe 0 → 0FF : 1 → 255 Slow to fast

3 Red Level from 0 to 255

4 Green Level from 0 to 255

5 Blue Level from 0 to 255

6 White Level from 0 to 255

7 Program 0 → Off : 1 → 255 Program (see programs table)

8 Program speed 0 → 127 slow to fast following the program’s course

128 → 255 slow to fast following the program’s counter-course

9 Palette 0 → 31 , the color program is the RGBW components of channels 3-4-5-6. with

a colored background on 10-11-12-13

with 4 repetitions of the color pixel.

RGBW Palette : 0→15 : 1 pixel over 2 RGBW background

RGBW Palette: 16 → 31 : 1 pixel over 4 RGBW background

RGBW Palette: 32 → 47 : 1 pixel over 8 RGBW background

RGBW Palette: 48 → 63 : 1 pixel over 16 RGBW background

Palette channel of 64 → 255 : 12 palettes of preset colors

Palette 1: 64 → 79 ,Palette 2: 80 → 95 ,Palette 3: 96 → 111 ,

Palette 4: 112 → 127 ,Palette 5: 128 → 143 ,Palette 6: 144 → 159 ,

Palette 7: 160 → 175 ,Palette 8: 176 → 191 ,Palette 9: 192 → 207 ,

Palette 10: 207 → 223 ,Palette 11: 224 → 239 ,Palette 12: 240 → 255

10 Red background Level from 0 to 255

11 Green background Level from 0 to 255

12 Blue background Level from 0 to 255

13 White background Level from 0 to 255

If the program is set to 0 with a clipped palette, the spotlight switches to Blinder mode

Mode 16 Channels

DMX Channel Description

1 Red Level from 0 to 255 of pixel 1

2 Green Level from 0 to 255 of pixel 1

3 Blue Level from 0 to 255 of pixel 1

4 White Level from 0 to 255 of pixel 1

5 Red Level from 0 to 255 of pixel 2

6 Green Level from 0 to 255 of pixel 2

7 Blue Level from 0 to 255 of pixel 2

8 White Level from 0 to 255 of pixel 2

9 Red Level from 0 to 255 of pixel 3

10 Green Level from 0 to 255 of pixel 3

11 Blue Level from 0 to 255 of pixel 3

12 White Level from 0 to 255 of pixel 3

13 Red Level from 0 to 255 of pixel 4

14 Green Level from 0 to 255 of pixel 4

15 Blue Level from 0 to 255 of pixel 4

16 White Level from 0 to 255 of pixel 4

Mode 18 Channels

DMX Channel Description

1 General Dimmer

2 Strobe 0 → 0FF : 1 → 255 Slow to fast

3 Red Level from 0 to 255 of pixel 1

4 Green Level from 0 to 255 of pixel 1

5 Blue Level from 0 to 255 of pixel 1

6 White Level from 0 to 255 of pixel 1

7 Red Level from 0 to 255 of pixel 2

8 Green Level from 0 to 255 of pixel 2

9 Blue Level from 0 to 255 of pixel 2

10 White Level from 0 to 255 of pixel 2

11 Red Level from 0 to 255 of pixel 3

12 Green Level from 0 to 255 of pixel 3

13 Blue Level from 0 to 255 of pixel 3

14 White Level from 0 to 255 of pixel 3

15 Red Level from 0 to 255 of pixel 4

16 Green Level from 0 to 255 of pixel 4

17 Blue Level from 0 to 255 of pixel 4

18 White Level from 0 to 255 of pixel 4

Mode 21 Channels

DMX Channel Description

1 General Dimmer

2 Strobe 0 → 0FF : 1 → 255 Slow to fast

3 Red Level from 0 to 255 of pixel 1

4 Green Level from 0 to 255 of pixel 1

5 Blue Level from 0 to 255 of pixel 1

6 White Level from 0 to 255 of pixel 1

7 Red Level from 0 to 255 of pixel 2

8 Green Level from 0 to 255 of pixel 2

9 Blue Level from 0 to 255 of pixel 2

10 White Level from 0 to 255 of pixel 2

11 Red Level from 0 to 255 of pixel 3

12 Green Level from 0 to 255 of pixel 3

13 Blue Level from 0 to 255 of pixel 3

14 White Level from 0 to 255 of pixel 3

15 Red Level from 0 to 255 of pixel 4

16 Green Level from 0 to 255 of pixel 4

17 Blue Level from 0 to 255 of pixel 4

18 White Level from 0 to 255 of pixel 4

19 Program 0 → Off : 1 → 255 Program (see programs table)

20 Program speed 0 → 127 slow to fast following the program’s course

128 → 255 slow to fast following the program’s counter-course

21 Palette 0 → 31 , the color rogram is the RGBW com onents of channels 3-4-5-6.

with a colored background on 7-8-9-10

with 4 repetitions of the color pixel

RGBW Palette : 0→15 : 1 pixel over 2 RGBW background

RGBW Palette: 16 → 31 : 1 pixel over 4 RGBW background

RGBW Palette: 32 → 47 : 1 pixel over 8 RGBW background

RGBW Palette: 48 → 63 : 1 pixel over 16 RGBW background

Palette channel of 64 → 255 : 12 palettes of preset colors

Palette 1: 64 → 79 ,Palette 2: 80 → 95 ,Palette 3: 96 → 111 ,

Palette 4: 112 → 127 ,Palette 5: 128 → 143 ,Palette 6: 144 → 159 ,

Palette 7: 160 → 175 ,Palette 8: 176 → 191 ,Palette 9: 192 → 207 ,

Palette 10: 207 → 223 ,Palette 11: 224 → 239 ,Palette 12: 240 → 255

If the program is set to 0 with a clipped palette, the spotlight switches to Blinder mode on one of the

colors of pixel 1

Program Channel DMX Zone :

Indice

Altri manuali Electroconcept Riflettore

Electroconcept

Electroconcept QUAD 188 Manuale utente

Electroconcept

Electroconcept M SPOT 200II Manuale utente

Manuali Riflettore popolari di altre marche

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente

LIVARNO home

LIVARNO home 375304 2101 Istruzioni originali

Cameo

Cameo CLQS40WW Manuale utente

Leviton

Leviton Ellipsoid 5/50 Manuale utente

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuale utente

Vector

Vector SL3AKV Manuale utente

Quantum

Quantum Q262 Manuale operativo

Philips

Philips Vari-lite VL3015LT Manuale utente

EUROSPOT

EUROSPOT C51 Manuale utente

DTS

DTS MINI BRICK ARC Manuale utente

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuale

ACME

ACME LED-MS350B Manuale utente

EuroLite

EuroLite Akku flat light 1 Manuale utente

Commercial Electric

Commercial Electric SPTM-1401 Manuale utente

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuale utente

Teknik

Teknik FLEXI Manuale utente

Craftsman

Craftsman CMXLSB10 Manuale utente

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuale utente