Go-Go Dancer - INTRODUCTION 2
M O D E L S
Read through this manual before starting construction. It contains important
instructions and warnings concerning the assembly and use of this model.
Go-Go Dancer is a 30-watt electric-powered sport park yer. Powered by a
small CD-ROM brushless motor and a 2-cell 640 mAh LiPoly battery, Go-Go
Dancer will give you spirited performance at a very affordable price.
The Go-Go Dancer Design
Go-Go Dancer is an original kit designed for modelers with an interest in
electric-powered airplanes capable of park ying and sport aerobatics. Go-Go
Dancer was designed from the beginning for lightweight brushless CD-ROM
motors and LiPoly cells. This airplane makes use of strong, lightweight design
and construction, which improves electric-powered ight performance and du-
ration. Using the suggested motor and cells, Go-Go Dancer weighs about 7 oz.
ready-to-y. Go-Go Dancer was designed to y a wide speed range and handle
windier conditions than most park yers. Aerobatics, from very tight maneu-
vers to large, powerful loops, slow rolls, snaps, and big stall turns are possible
with Go-Go Dancer. Go-Go Dancer is very stable, and if trimmed out right, will
almost land itself. Go-Go Dancer is controllable and ies smoothly even in high
winds, yet slows down and lands like a feather. Go-Go Dancer is a great-ying
electric-powered model that ies predictably - not your typical “ip-and-op”
park yer. Go-Go Dancer should not be own by a beginner R/C pilot.
Go-Go Dancer was designed to make motor battery changes as easy as possible,
with no tools required. You don’t have to turn the airplane over or remove the
wing to change batteries. Just lift the front battery hatch up and ip it forward
for easy battery access. The hatch is hooked in the front and small magnets
hold the hatch rear in place. The recommended motor for Go-Go Dancer is the
GoBrushless basic CD-ROM motor kit with 16 turns powered by 2S1P - 640mAh
LiPoly cells at 5 amps. A 6” x 4” prop is recommended. This combination gives
spectacular performance and long ight times. Go-Go Dancer is light, yet tough.
Go-Go Dancer is a simple-to-build, y-anywhere airplane that is one of the best
ways to get into brushless performance on a budget.
This kit features leading edge design and interlocking laser-cut parts for excep-
tional t, quality, and ease of construction. A complete set of hardware is also
included. The Go-Go Dancer plans were drawn on a computer using professional
design software. We believe that the Go-Go Dancer plans are a work of art and
continue our high standards in kit manufacturing at ElectroFlying Models.
Easy-building engineering, great price, brushless performance and great ying
qualities, the Go-Go Dancer has it all.
WARNING!
This is not a beginner's airplane. This R/C kit and the model you will build from
it is not a toy! It is capable of serious bodily harm and property damage. It is
your responsibility, and yours alone, to build this kit correctly, properly install
all R/C components and ying gear (motor, batteries, speed control, radio,
servos, pushrods, etc.) and to test the model and y it only with experienced
competent help, using common sense and in accordance with all safety stan-
dards as set forth in the Academy of Model Aeronautics (AMA) Safety Code.
It is suggested that you join the AMA and become properly insured before
attempting to y this model.
Warranty
ElectroFlying, Inc. guarantees this kit to be free from defects in both materials
and workmanship at the date of purchase. This warranty does not cover any
components damaged by use or modication. In no case shall ElectroFlying‘s
liability exceed the original cost of the purchased kit. Further, ElectroFlying
reserves the right to change or modify this warranty without notice.
ElectroFlying has no control over the nal assembly or material used for nal
assembly, therefore no liability shall be assumed nor accepted for any damage
resulting from the use by the user of the nal user-assembled aircraft kit. By
the act of using the user-assembled aircraft kit, the user accepts all resulting
liability.
If the buyer is not prepared to accept the liability associated with the use of
this aircraft kit, the buyer is advised to return this kit immediately in new and
unused condition to ElectroFlying, Inc.
Follow These Important Safety Precautions:
1. This kit should not be considered a toy, but rather a sophisticated, working
model that functions very much like a full-size airplane. Because of its perfor-
mance capabilities, it could cause injury to yourself and spectators or damage
to property, if it is not assembled and operated correctly.
2. You must assemble the model according to the instructions. Do not alter or
modify the model, as doing so may result in an unsafe or unyable model.
3. You must take time to build straight and strong. You should not use any
materials or kit supplied parts that you suspect are defective or damaged.
Request replacement kit parts from ElectroFlying, Inc.
4. You should only use R/C radio systems that are in perfect working order.
5. You must check the operation of the model before every ight to ensure
that all equipment is operating and that the model has remained structurally
sound. Replace any part that shows any sign of wear or fatigue.
6. Check control surface travel and direction before each ight.
7. Do a radio range check before the rst ight or after any change to the
model's radio system. Never use a radio system that has been involved in a
crash without a professional check-out and repair if needed.
8. Do not over-power this kit. Use only recommended electric motors and cells.
9. If you are not already an experienced R/C pilot, you should y the model
only with the help of a competent, experienced R/C pilot.
10. While this airplane kit has been ight tested to exceed normal use, the
airplane should not be used for high stress ying, such as racing.
We,as the kit manufacturer,provide you with a top quality kit and instructions,
but ultimately the quality and flyability of your finished model depends on how
you build it;therefore,we cannot in any way guarantee the performance of your
completed model, and no representations are expressed or implied as to the
performance or safety of your completed model.
