Electrolux EGG7222SX Manuale utente
SERVICE MANUAL
1
C O N T E N T S
1. GENERAL NOTES 2
2. HOW DOES GAS BURNER OPERATE 3
3. COMPONENTS SPECIFICATION 4
3.1 City gas a essories 5
4. TOOLS 6
5. REPAIR PROCESS 6
5.1 Remove the dirty oil from nozzle
5.2 Remove the gas valve
6. WIRING DIAGRAM 8
7. CONVERSION DETAILS 9
8. TAKE CARE OF GLASS TOP 9
9. SPARE PARTS 10
10. TROUBLE SHOOTING 19
2
1. GENERAL NOTES
1.1 WARNING: For models which connect to mains electrical power, before exposing an of the internal
electrical wiring the appliance must be disconnected from electrical power b unplugging the service cord
from the electrical outlet. For models which connect to batter power, before exposing an of the internal
electrical wiring the appliance must be remove the batter also.
1.2 An servicing carried out on gas containing components where seals are broken including manifold,
regulator, valves and burner suppl pipes should be followed b a leak test. Gross leaks can be detected b
connecting a manometer to the regulator test point, pressurising the manifold and then shutting off the gas
with a ball valve. A falling manometer reading indicates a leak. Small leaks can be located with soap and
water applied at the connection.
1.3 Burner suppl pipes leading from the burner control to the burner should have their compression fittings
tightened firml but not over tightened (If a torque spanner is used set this to 10 12Nm). If the tubes are
damaged the should be replaced. The soundness of the connections on the burner suppl tubes can be tested
b blocking the injector orifice temporaril , eg. b fitting an injector that has been blocked and leak testing
the fittings.
1.4 When reassembling the appliance any earth leads whi h have been dis onne ted must be re- onne ted.
1.5 Reassembl procedures are a reversal of removal procedures.
1.6 Replace the spare part with original spare parts. The modif part must not be used.
1.7 All the screws in this appliance have been designed for difference purpose. The must be use in the right
position and must be the right dimension. If there are an differences from the original design the ma have
the serious accident.
3
2. HOW DOES GAS BURNER OPERATE
1. Gas tank
2. Low pressure regulator (Safety warning: Do not use high pressure regulator)
3. Flexible rubber hose or copper tube
4. Elbow coupling gas with fibre washer (Warning: Do not use regular rubber washer)
5. 2 steps safet valve
6. Burner
7. Ignition switch
8. Batter 1.5V size D
9. Spark generator
10. Spark plug
1
2
3
4
5
6
7
8
9
10
4
Gas from the tank (1) is released from the low pressure regulator (2) into the hose or tube (3), travelling pass
the elbow coupling to the valve (4). To ignite the burner, press down and turn the safet valve (5) counter-
clockwise simultaneousl . This opens up the valve, letting the gas to the nozzle of the burner (6), and turns the
ignition switch to on (7) at the same time. The electrical current is automaticall supplied from the batter to
spark plug generator (8), and then to the pin heads (9), causing the ignition (10). The burner is ignited and bursts
into flame (11).
3. COMPONENTS SPECIFICATION
- Glass 2B : Float glass 8.0x500x760 mm
- Bottom plate forming : EG
- Knob : Phenolic PH31 heat + flame resistance
- Washer : fiber
- Hose end : Brass (size1/2)
- Rubber grommet (glass model) : Silicone heat resistance
- Spark generator 4p : 1.5Vdc+90C+electrode10KV
5
3.1 Citi Gas A essories
- Shutter Aeration (Semi Papid)
(TH-0003/ZA)
- Shutter Altration ( Triple Crown)
(TH-0003/ZB)
- Injector 2.1 (Semi Rapid)
(TH-0003/CD)
- Injector 4.0 (Triple Crown)
(TH-0003/ZA)
- Injector 3.5 (Defendi Outer)
(TH-0003/CL)
- Shutter Aeration (Defendi Outer)
(TH-0003/ZC)
- Injector 1.2 (Defendi Outer)
(TH-0003/CM)
- Shutter Aeration(Defendi Inner)
(TH-0003/ZD)
6
- Screw, M4x0.7x10 IP
- Screw, M4x0.7x18 H
- Screw, M3x12T + B stainless
- Screw, #6/32 x 9 PPZF
- Screw, #8 x ½ T+ Z
4. TOOLS
- Socket Spanner 7
- Nut spinner No. 7
- Philip / Flat screw driver
- Spanner No. 15
- Nozzle cleaner
- Gas leak detector
5. REPAIR PROCESS
5.1 Remove out the dirt oil from nozzle
1. Clean the head of nozzle with the cloth
2. Use the nozzle cleaner or the needle insert into the hole of nozzle.
3. Do repeat the step 1 and 2 for a few time until the nozzle is clean.
5.2 Removal of Hob & Access to Internal Components
1. Isolate the appliance from batter power.
2. Remove trivets and burners from hob.
3. Remove the control knobs from the valve shafts.
7
4. Remove burner mount retaining screws, 2 screws per burner and 4 on the wok burner (2.5mm Torque
Screwdriver required).
5. For models with a separate button ignition s stem, remove the switch button and ignition pack retaining nut.
Alternativel , lift the hob sufficientl to access and release the ignition leads and batter suppl cable from
the ignition pack.
6. The hob ma now be lifted awa from the appliance.
B removing the hob the following parts are accessible for service or replacement.
• Burner mounting cups.
• Burner suppl tubes. Note: When fitting the burner tubes to the valves and burner mounting
cups the nuts should be fastened with a torque of 10-12Nm.
• Manifold & Valves. Note: To remove the manifold or valves it will be necessar to isolate and
disconnect the appliance from gas suppl .
8
• Switch harness assembl and low voltage wiring.
• Ignition spark plug and lead assemblies. These are fastened to the burner bases b retaining clips, located on
the underside of the burner base.
• Ignition pack. For models without a separate ignition switch this is clipped to the base or attached with
double sided adhesive. For models with a separate ignition switch this is fastened to the hob with a retaining
nut. Observe the active & neutral are correctl connected in accordance with the markings on the ignition
pack when replacing this unit.
6. WIRING DIAGRAM
9
7. CONVERSION DETAILS
The applian e is onvertible between Natural Gas & LP.
Pro edure
1. Turn off gas suppl to appliance.
2. Disconnect appliance from electrical power.
3. Remove the trivets and the burner caps & distributors.
4. Remove the existing injectors and replace with the injectors shown in the table below.
5. Remove the control knobs to access the b -pass screw in the valve bodies.
6. Remove the regulator and replace with appropriate regulator or test point adapter as stated in table below,
and reconnect the appliance.
7. Turn on gas & check for leaks. Replace the Burner crowns & caps.
8. Check and adjust the test point pressure according to the procedure in the installation instructions.
9. Manuall light all burners with a hand held ignition source and operate burners at maximum. Note: Do not
reconnect the appliance to electrical power until this procedure is complete.
10. For each hotplate burner adjust the burner to minimum and screw in the b pass screw until a small stable
flame results. Adjust the burner to maximum and back to minimum to ensure correct adjustment.
11. Re-connect to electrical power and check ignition.
8. TAKE CARE OF GLASS TOP
Persistent stains ma require vigorous rubbing with n lon scourer or creamed powers cleansers. Household
enamel cleaners are available. Following the instruction in their use. Harsh abrasive cleaner ,powder cleaner
steel wool or wax polishes should not be used. Advise end user do not use glass as per working top.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Electrolux Piano cottura
Electrolux
Electrolux E36IC75FSS4 Manuale utente
Electrolux
Electrolux E36EC75ESS Manuale utente
Electrolux
Electrolux 318201475 Manuale utente
Electrolux
Electrolux E30EC65ESS - 30 Inch Smoothtop Electric... Manuale utente
Electrolux
Electrolux 318 200 687 Manuale utente
Electrolux
Electrolux 584146 Manuale utente
Electrolux
Electrolux EW30CC55GB Manuale utente
Electrolux
Electrolux E48GC76EPS - 48" Sealed Burner Slide-In Gas... Guida rapida
Electrolux
Electrolux EW36IC60IB - 36" Induction Cooktop Guida rapida
Electrolux
Electrolux E36GC70FSS1 Manuale utente
Electrolux
Electrolux E30IC75FSS5 Guida utente
Electrolux
Electrolux WLGWACOOOO Manuale utente
Electrolux
Electrolux E36EC65ESS2 Manuale utente
Electrolux
Electrolux EW30GC60IS Guida rapida
Electrolux
Electrolux GC1G21A1B Manuale utente
Electrolux
Electrolux ICON E36IC75FSS Manuale utente
Electrolux
Electrolux Competence Series Manuale utente
Electrolux
Electrolux EW36IC60IB - 36" Induction Cooktop Manuale
Electrolux
Electrolux EHD90LLUM Manuale utente
Electrolux
Electrolux Built-in appliances Manuale utente
