Electronics Line EL-4800 Manuale utente

Wireless Outdoor PIR

Two-Way Wireless Outdoor PIR Detector

Model: EL-4800

Installation Instructions

Table of Contents

Introduction ............................................................................................................................4

Mounting.................................................................................................................................4

Mounting Considerations......................................................................................................4

Installing the Wireless Outdoor PIR Detector in challenging situations ...........................5

Wall Mount Installation .........................................................................................................6

Flat Mounting: ......................................................................................................................6

45° angle Mounting (Left side mounting): .............................................................................6

Changing Back Tamper position: .........................................................................................7

Back Tamper Terminal Wiring ...............................................................................................8

Detection Range Adjustment.................................................................................................8

Walk test .................................................................................................................................9

LED Display ..........................................................................................................................10

Operational Modes ...............................................................................................................10

Transmitter/Receiver Communication link setup ...............................................................10

Optional Swivel Installation (Not Supplied) ........................................................................10

Wall Mounting ....................................................................................................................10

Replacing Lenses.................................................................................................................13

Technical Specification........................................................................................................14

Ordering Information............................................................................................................14

Accessory Kits .....................................................................................................................14

Introduction

Electronic Line’s Wireless PIR Outdoor Detector is a unique detector with signal processing

based on two Passive Infrared (PIR) channels. The detector has an adjustable detection range. The

detector is compatible with all Electronic Line’s Wireless and Hybrid systems.

The following instructions describe the installation of the Wireless PIR Outdoor Detector.

Mounting

Mounting Considerations

1. Installation Height: 0.8m - 1.2m

(2'8" – 3'11")

Typical Installation Height: 1m (3'3")

2. To ensure maximum operational reliability, install the detector perpendicular to the ground so

that the upper detection area is parallel to the ground.

3. For optimum detection,

select a location that is likely

to intercept an intruder

moving across the coverage

pattern.

4. Avoid pointing the detector to moving

objects (swaying trees, bushes etc.)

Out of

Detection Range

With moving objects

keep distance of

minimum 5 meters (16')

5m (16')

5. Ensure any objects do not obstruct the field

of view. Pay attention to growing trees or

bushes, plants with big moving leaves etc.

Installing the Wireless Outdoor PIR Detector in challenging situations

In the following situations, rapid and significant infrared radiation changes can happen in both

PIR channels together, resulting in false alarms and therefore care should be taken.

1. Situations in which metal and/or glass objects measuring over 70cm (2’4”) in height from the

ground are in the field of view of the detector (cars, metal gates, shutters, metal walls,

windows, etc.)

2. Situations in which a reflective surface on the ground larger than 1m (3’4”) in diameter may

cause reflection into the detector’s lens. Examples of a reflective surface on the ground are a

puddle, wet road or car park, smooth concrete or asphalt surface, swimming pool, etc.

Water Reflection

Notes:

1. Please note that any outdoor PIR detector will require reduction in range to a shorter distance than the car,

metal object or surface reflection (so that these objects won’t be protected) in order to eliminate false alarms.

2. For full 15m (50’) coverage in the above situations, it is highly recommended to install the Wired DT Outdoor

Detector, the only outdoor detector with 2 PIR channels and 2 Microwave channels.

3. Wireless Outdoor PIR detectors include high quality Silicon filters on the PIR sensors for blocking out

white light interferences. These filters are not intended to block infrared thermal radiation.

Wall Mount Installation

Note:

The installation knockouts numbering are marked

on the back plate.

1. Open the Wireless PIR Outdoor

Detector front cover (unlock C1, Figure

1).

2. Release internal base (unlock I1, Figure

2).

3. Select mounting installation as follows:

Flat Mounting:

Open knockouts on external base (Figure

3).

•B1 - B4: Wall mounting knockouts

•T1: Back tamper knockout

45° angle Mounting (Left side

mounting):

a. Open knockouts on external base

(Figure 3).

•L1, L2: Left mounting knockouts

•T3: Left tamper knockout

b. Remove tamper spring (Figure 4).

c. Replace tamper bracket (Item 1) with

supplied flat tamper bracket (Item 2).

Item 1

Item 2

d. Insert Tamper lever B onto T6 and T3

and secure screw A (Figure 3).

4. Secure external base to the wall.

5. Insert tamper wires through internal base

(Figure 4).

6. Secure internal base to external base

(lock I1, Figure 2).

7. Close the front cover (Lock C1, Figure 1)

after wiring and setting DIP switches.

8. Walk test the detector.

Figure 1

Figure 2

Figure 3

Tamper

Lever

(not visible)

Figure 4

Note:

For 45° right side installation use the equivalent units on the external base as follows:

Knockouts Description Lef

Righ

Mounting Knockouts L1, L2 R1, R2

Tamper spring knockouts T1,T3 T2,T4

Tamper screw anchor T5 T6

Changing Back Tamper position:

The back tamper is by default secured on the right

side of the internal base (Rear view). If you wish to

move it to the left side (rear view), do the following

(Figure 5):

1. Remove tamper screw 1 in order to release the

tamper from position 7.

2. Ensure tamper spring (2) rests over tamper wire

base 4.

3. Ensure plastic tamper bracket (3) rests over

both 2 and 4.

4. Secure tamper screw (1) into (3) over position 6.

Figure 5

Left Side

Tamper

Right Side

Tamper

Notes:

1. Verify that you hear a "Click" when attaching the tamper spring to the wall.

2. For pole installation, the tamper can be moved to the bottom right-hand side of the internal base.

Back Tamper Terminal Wiring

If you wish to use the back tamper (recommended) remove the short from the back tamper terminal

block and connect the back tamper wires to the back tamper terminal block.

Back Tamper in use

BACK TAMPER

Back Tamper not used

Short

H1 H1

Detection Range Adjustment

Slide the moving PIR to the desired

position, see figure 6.

The range of the lower detection area

determines the detection range.

The upper PIR is fixed and its detection

area is parallel to the ground at all times.

The lower detection area changes from

2m to 12m depending on the location of

the moving PIR. Therefore, the detection

range is established according to the

location of the lower PIR since both the

upper and the lower PIR should be

triggered in order to activate an alarm.

Figure 6

Detection patterns (side view):

Detection range with 1m (3'3")

installation height:

* Note:

Length may vary according to

environmental thermal conditions.

Note:

No effective detection occurs at distance

less than 2.5 ft from the detector.

Walk test

Two minutes after applying power, walk test the protected area to verify proper operation.

Adjust the moving PIR for required detection range and reliability.

Important!

Both upper and lower detection areas must be blocked simultaneously for detection to occur, see figure 7 below.

Figure 7

LED Display

LED State Description

RED Steady Indicates ALARM

Operational Modes

Operational Mode Description

Normal Dead time (between detection alarms) is 2.5 Minutes.

Test (walk test) Dead time (between detection alarms) is 3 sec.

Note:

After power up the detector enters into test mode for a period of 20 minutes (disregarding the DIP Switch Modes

Position).

Transmitter/Receiver Communication link setup

The detector must identify itself to the control panel’s receiver by registering its coded message into

the receiver’s address memory. This is accomplished by performing the following steps:

1. Set the receiver to Registration Mode.

2. Remove the insulation material from the battery and place it in the battery holder on the PCB on

the right direction (pay attention to the "+" and "–" diagram on the PCB)

3. Send a registration message by closing both of the tamper switches (back and cover) for at

least 3 seconds.

4. Verify that the detector has been identified by the receiver.

Caution Notice

Changes or modifications not expressly approved by Electronics Line may void the user’s authority to operate this

equipment.

Simultaneous transmissions from two different units may cause message interference resulting in loss of

information.

The communication quality of this unit may be affected by its surrounding environment. Nearby electrical

equipment may interfere with its normal operation.

The operation of this unit must, therefore, be tested at each installation since its transmission quality may vary as

a result of operational conditions.

Optional Swivel Installation (Not Supplied)

Please follow the instructions below for mounting the detector with the Swivel:

1. Open the Wireless PIR Outdoor Detector front cover (Unlock C1, Figure 1).

2. Release internal base (Unlock I1, Figure 2).

3. Remove back tamper from the internal base (see the “Changing Back Tamper Position"

paragraph on page 7) and connect it to S5 (Figure 8, Detail A) on the Standard Swivel.

4. Select the mounting installation as follows:

Note:

•The swivel mount has not been evaluated by UL

•Ensure that you see the engraved UP mark on the upper front face of the swivel.

Wall Mounting

1. Insert back tamper wires through the Swivel Wires Passage (Figure 8, Detail B).

2. Secure swivel to the wall through holes S1, S3, S6 and S8.

Indice

Altri manuali Electronics Line Sensore di sicurezza

Electronics Line

Electronics Line EL-2800 Manuale utente

Electronics Line

Electronics Line EL-4755 Manuale utente

Electronics Line

Electronics Line EL5845 Manuale utente

Electronics Line

Electronics Line EL-2650XL Manuale utente

Electronics Line

Electronics Line EL-1484 Manuale utente

Electronics Line

Electronics Line EL-4607 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente