ELEKTRA CX Series Manuale utente
Electric bathroom
dryers
ELEKTRA CX
RU
Instrukcja montażu PL
Installation manual UK
Èíñòðóêöèÿ ïî ìîíòàæó
www.elektra.eu
Key safety notes
Unless it is used under super-
vision or in accordance with the
instructions provided by persons
responsible for their safety, the
product must not be operated by
children under the age of 8 or
individuals with sensory-motor or
mental disability or persons with
previous experience with or
knowledge about the product.
Children must not play with the
product. Unsupervised children
must not clean or perform
maintenance of the product.
• The product may only be used
for its intended purpose
following all instructions for
installation and operation
included in this manual.
• The heated towel rail is not
a toy, therefore keep the
appliance out of reach of
children without parental
supervision.
3
Note:
• For the sake of safety of
children the heated towel rail
should be installed so that its
bottom part is out of reach
of small children, i.e. at least
60 cm above the floor.
• Please mind that the surface of
the working towel rail is hot.
Touching it can result in burns.
• The heated towel rail is not
a weight-bearing structure.
Avoid stepping on it or using
it as a ladder.
• Do not immerse any part of
the appliance in water
(e.g. in a bathtub etc.).
• The product is fitted with
a nondetachable power supply
cord which, in case of any
damage, should be replaced by
manufacturer or in a dedicated
repair shop, in order to avoid
danger.
• In case of inappropriate
functioning of the appliance,
or any damage to its elements,
4
Electric bathroom
dryers ELEKTRA CX
immediately disconnect the
mains plug and contact
the vendor.
• Removal of the protective
plugs, placing objects into the
appliance or filling the body up
with liquid in prohibited. Such
activity may cause electric shock
or damage to the towel rail.
• Repairs and technical modifica-
tions carried out by unqualified
personnel may be dangerous
for users.
• Should any additional connect-
ing elements, such as regula-
tors, switches, extension leads
etc. be required, they must be
selected appropriately
(see information included in
their technical specifications)
and they must comply with the
applicable laws and regulations.
• If you are out of home for
a longer period of time, as
well as during cleaning of the
towel rail, disconnect the mains
plug (do not pull the cord!)
5
or, for the CX...N version, switch
the device off by using the
ON/OFF switch.
The electric heated towel rail
must be situated at least 60 cm
away from baths, basins, sinks,
showers, pools etc.
PLEASE USE THE APPLIANCE IN
ACCORDANCE WITH THE GUIDE-
LINES INCLUDED IN THE
INSTALLATION, USE AND MAIN-
TENANCE INSTRUCTION MANUAL
AND READ THE WARRANTY
CONDITIONS.
6
Electric bathroom
dryers ELEKTRA CX
Application
Technical data
ELEKTRA CX electric bathroom dryer is intended
for drying towels, garments etc. washed in
water. It can be installed in any room where
electric power is available (~230V, 50/60Hz),
and is especially suited for bathrooms, kitchens,
bathing rooms, hairdressers' etc. The bathroom
dryer's design ensures its constant safe opera-
tion. The temperature increase of the dryer's
exposed surface, during continuous operation,
does not exceed 60°C.
Power supply: ~230V AC, 50/60Hz
Power consumption: 95÷230W
Power consumption depends on bathroom dryer
type. Power consumption data are given on the
nameplate.
Power output and IP protection rate: dependent
on the model of the heated towel rail.
For relevant information, see the rating plate.
Weight: Weight depends on the model of the
heated towel rail and is stated on the product
label.
Protection Class according to IEC: I (The electric
heatedtowelrailisaIprotectionclassapplian-
ce. It means that the power supply cord is
fitted with a protective conductor, which must
be connected to the PE protective conductor of
the electrical system directly - for the CX...N
version of the device, or through a socket
equipped with an adequate protective pin
– for the standard version of the device. 7
Mounting Instructions
of the standard CX version
of the dryer, with a plug
1. Assemble the brackets without screws (6)
and plugs (8) (as per the drawing).
2. Select bathroom dryer position on the wall.
3. Drill holes at pre-located points,
and insert plugs.
4. Using screws (6) mount brackets (7)
to the wall (as per the drawing).
5. Using screws (9) fix the bathroom dryer
and heater to the bracket, together with
the elements previously mounted to it.
Body of the dryer
M6 screw
Ø13 sleeve
Washer
M6 nut
1
2
3
4
5
Screw 6x70
Body of the bracket
Plug Ø10x50
Screw 2.9x9.5
6
7
8
9
Bracket elements
8
Electric bathroom
dryers ELEKTRA CX
Body of the dryer
Body of the bracket
1
2
Bracket elements for the bathroom dryer CX…N
9
Mounting Instructions
of the special CX...N
version of the dryer,
with a power supply cord
in the dryer's body
The special CX...N version of the bathroom dryer
varies from the standard one with the power
supply cord of the dryer led directly out
through the body, and not terminated with
a plug.
1. Mount elements of the three brackets of the
dryer according to the mounting instructions
of the standard CX version of the dryer
above.
2. The fourth element, through which the
power supply cord is led, is not mounted
to the wall.
Screw 2.9x9.5
Power supply cord
3
4
Connection to the mains
and adjustment
(switching the appliance on & off)
To start the bathroom dryer's operation, for the CX
standard version of the device (with a plug), insert the
plug into an earthed electrical socket (230V ~50Hz).
• In order to start the operation of the heated towel
rail, connect the plug to an earthed electrical socket
and set the switch into position "I". Occasional
monitoring of the appliance's operation is advisable.
• Only original factory fitted elements (cords, plugs)
can be used for direct electrical mains connection of
the appliance.
• To switch off the heated towel rail, it is enough to
set the switch into position "0" it is not necessary
to disconnect the mains plug.
• For the heated towel rails fitted with power supply
cords without plugs, designed for fixed connection
to electrical mains, electrical wiring must be equipped
with protective devices enabling disconnection of the
appliance on both poles for bipolar switches, or
disconnection of the live wire from the power supply
for unipolar switches. Applied devices for disconnection
from the power supply should be designed so that
their air gaps should exceed 3 mm.
To start the bathroom dryer's operation, for the
CX...N version of the device with the power supply
cord in the body (without a plug):
10
Electric bathroom
dryers ELEKTRA CX
Packaging elements can be dangerous
for children. Keep the packaging out of
reach of children.
Note:
Altri manuali per CX Series
1
Questo manuale è adatto per i seguenti modelli
19
Indice
Lingue:
Altri manuali ELEKTRA Asciugatrice
