Element14 LCD8000-97C Manuale utente

LCD8000-97C

A 9.7” LCD Module for SABRE Lite & MarS Board

User Ma ual

Versio 1.0

Dated: 10

December 2013

Revisio History:

Version Date Description

1.0 10/12/2013 Original Version

Table of Co te ts

1: Product Overview .......................................................................... 1

1.1: Packing List .......................................................................... 1

2: Hardware Features ........................................................................ 2

2.1: Operational Parameters .......................................................... 2

3: Usi g LCD8000-97C With the MarS Board ...................................... 3

3.1: Hardware Connections ........................................................... 3

3.2: Software Configurations ......................................................... 4

4: Usi g LCD8000-97C o SABRE Lite ................................................ 7

4.1: Hardware Connections ...........................................................

4.2: Software Configurations ......................................................... 8

Page |

1: Product Overview

The LCD8000-9 C is a 9. ” capacitive touchscreen developed by element14

for use with the MarS Board - a super ARM DIY platform, and SABRE Lite.

The LCD8000-9 C has an LVDS interface and supports a resolution of up to

1024x 68 and 260,000 colours. Its multi-touch screen brings an enhanced

experience to the users of the MarS Board and the SABRE Lite.

1.1: Packi g List

LCD8000-9 C

Mini HDMI C-to-C Cable (for Mars Board)

LVDS Cable (for SABRE Lite)

Page |

2: Hardware Features

9. ” TFT Screen

Resolution of 1024x 68, 260,000 colours

Supports LVDS Signals

Multi-Touch Capacitive Touch-Screen

2.1: Operatio al Parameters

Operating Ambient Temperature: 0°C ~ +50°C

Storage Temperature: -25°C ~ +65°C

Operating Humidity: 20% - 90%

Dimension: 239mm x 185mm

Power Supply: +5V (provided by MarS Board or SABRE Lite)

Page |

3: Usi g LCD8000-97C With the MarS

Board

3.1: Hardware Co ectio s

1) Use the Mini HDMI cable provided with the product to connect the

LVDS interface on the MarS Board to the Mini HDMI interface on the

LCD8000-9 C as shown below;

Figure 1

Connection between MarS Board and LCD8000-97C

2) Use a (Type Mini B Male to Type A Male) USB cable to connect the USB

debugging interface on the MarS Board to a USB interface on your PC,

and then connect a 5V power supply to the board to finish the

hardware connections as shown below;

Page |

Figure 2

Complete hardware connection

3.2: Software Co figuratio s

1) The latest images and source code for Linux and Android on the MarS

Board have been updated to support the LCD8000-9 C.

For download please visit: www.element14.com/iMX6

2) Please refer to the MarS Board User Manual for detailed instructions

on how to update the Linux/Android images on the board;

3) After updating is done, please reboot the MarS Board and press any

key on your PC’s keyboard to enter u-boot when you see “Hit any key

to stop autoboot” in your terminal window.

U-Boot 2009.08-svn1 (Mar 14 2013 - 14:07:49)

CPU: Freescale i.MX6 family TO0.0 at 792 MHz

Temperature: 51 C, calibration data 0x58150469

mx6q pll1: 792MHz

mx6q pll2: 528MHz

mx6q pll3: 480MHz

mx6q pll8: 50MHz

Page |

ipg clock : 66000000Hz

ipg per clock : 66000000Hz

uart clock : 80000000Hz

cspi clock : 60000000Hz

ahb clock : 132000000Hz

axi clock : 264000000Hz

emi_slow clock: 29333333Hz

ddr clock : 528000000Hz

usdhc1 clock : 198000000Hz

usdhc2 clock : 198000000Hz

usdhc3 clock : 198000000Hz

usdhc4 clock : 198000000Hz

nfc clock : 24000000Hz

Board: MX6Q-MARSBOARD:[ POR]

Boot Device: I2C

I2C: ready

DRAM: 1 GB

MMC: FSL_USDHC: 0,FSL_USDHC: 1

JEDEC ID: 0xbf:0x25:0x41

Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8

SUCCESS

*** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Net: got MAC address from IIM: 00:00:00:00:00:00

----enet_board_init: phy reset

FEC0 [PRIME]

Hit any key to stop autoboot: 0

(press any key to enter uboot)

MX6Q MARSBOARD U-Boot >

4) Execute the following instructions to set the display mode for the

9. -inch LVDS LCD;

setenv bootargs console=ttymxc1,115200 init=/init rw video=mxcfb0:dev=ldb,

LDB-XGA,if=RGB666 fbmem=10M vmalloc=400M androidboot.console=ttymxc1

saveenv

Note:

At present, the touch screen of LCD8000-9 C only supports single point touch

Page |

on a Linux based system

Reboot the MarS Board again and the process will be complete. You

can now use the LCD8000-9 C.

Page |

4: Usi g LCD8000-97C o SABRE Lite

4.1: Hardware Co ectio s

1) Use the LVDS cable provided with the product to connect the Mini

HDMI interface on the LCD8000-9 C to the LVDS and IIC interfaces

on the SABRE Lite as shown below:

Figure 3

Connections between SABRE Lite and LCD8000-97C

2) Use the serial cable provided with the SABRE Lite to connect the serial

interface on the device to your PC. Following this, insert a TF card into

the SABRE Lite and connect a 5V/4A power supply to finish the

hardware connection as shown below:

Indice

Manuali Tavoletta popolari di altre marche

Laser

Laser MID-1060 Guida utente

MUNBYN

MUNBYN IRT09J Guida rapida

Motorola

Motorola MC3090R - Win CE 5.0 Professional 520 MHz Manuale utente

Dell

Dell Latitude ST Manuale del proprietario

Lenovo

Lenovo IdeaTab S6000L Manuale del proprietario

Venturer

Venturer WT9L11 Manuale utente

EDUGEAR

EDUGEAR UnoBook Manuale utente

Philips

Philips PI3210G/58 Manuale utente

ADLINK Technology

ADLINK Technology IMT-BT Manuale utente

TwinMOS

TwinMOS TwinTAB-T102D1 Manuale utente

Archos

Archos 9.7 xenon Manuale utente

Getac

Getac E100 Manuale utente

HANNspree

HANNspree HANNspad SN70T3 Manuale utente

Philips

Philips PI3105W2/55 Manuale utente

LG LG-V935 Manuale utente

Zeki

Zeki TBDB763B Manuale utente

Ricoh

Ricoh eQuill Manuale utente

DT Research

DT Research DT365CT Istruzioni per il montaggio