eletab ELTGM01-2 Manuale utente
CAUTION:
IMPORTANT:
Read the entire instrution manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, Please
contact at EleTab_service@outlook.com for assistance.
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
Ensure that you have received all parts according to the component checklist prior to
installation. If any parts are received damaged or defective, please contact us at
EleTab_service@outlook.com. We are happy to replace parts to ensure you have a fully
functioning product.
• Mounts must be attached as specified in assembly instructions. Improper installation
may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by
professionals.
• Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
• This procuct is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
PRODUCT LINE GRAPH
Tools required
Components
Hardware
Parts
L(x1)
4mm Allen
Wrench
B (x2)
VESA Plate
H (x1)
Base Support
I (x1)
Support Plate
J (x1)
Knob
K (x2)
Pad
D5 (x4)
M-C
Washer
M5x12mm (x4)
M-B
Screws
M4x12mm (x4)
M-A
Thumbscrews
C (x1)
Clamp Base
Support
D (x1)
Clamp
E (x1)
Cable Clip
F (x1)
Long Screw
G (x5)
Bolt
M(x1)
5mm Allen
Wrench
A (x1)
Arm
(not included)
Phillips
Screwdriver
X2
OPTION A: Clamp Installation
Install clamp base support (C) onto base of monitor stand (A) with bolts (G)
using provided 4mm Allen wrench (L). Apply pads (K) to bottom of base.
Secure clamp (D) to upper two holes with
bolts (G) using 4mm Allen wrench (L) for
desks with a thickness of 10-55mm.
Secure clamp (D) to lower two holes with
bolts (G) using 4mm Allen wrench (L) for
desks with a thickness of 50-85mm.
STEP 1 Choose a mounting option
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide long screw (F) through the top of the grommet base support (H) and install on base of
monitor stand with bolts (G) using 4mm Allen wrench (L). Apply pads (K) to bottom of base.
Attach base support cover (E) to clamp base support (C). Tighten the clamp to the
desktop using the plastic knob.
Position stand on desk with long screw through hole, and secure by using the support plate (I)
and clamp knob (J) on underside of the mounting surface.
STEP 2 Attach the monitors to the arm
Position VESA plate (B) on back of monitor and
secure with screws (M -A) or (M-B) with (M-C)
washers.
Pull the tab on the spring arm (A) ① and slide the VESA
monitor mount and monitor into the mount on the
spring arm.②
②
①
Adjust spring tension by turning
screw with 5mm Allen wrench (M) .
Turning it clockwise can increase the
display tension and fix it. Turning
counterclockwise slightly reduces
the display tension and adjusts.
Remember not to go to the limit,
otherwise the spring slack will cause
the bracket to be useless.
Just slide the cable cover up and away from
the spring arm, do not need to take much
effort to pull the ends of the cable cover
away from the spring arm.
Insert the cable and slide the cable cover
down to reattach the cable cover.
If needed, adjust the bolt on
the side of the hinge behind
the VESA plate to tighten or
loosen the tilt angle support.
Be sure to keep the arm in horizontal
position during adjustment .0r else it
would be difficult to adjust the mount or
damage the mount.
STEP 3 Adjust the tension
STEP 4 Cable management
EleT[email protected] www.facebook.com/EleTabus
WARRANTY SERVICE
Feedback
To provide the best service to you, do not forget to register
your EleTab product to confirm your warranty.
It only takes a few simple steps and then you can access a
wide-range of services such as technical support, new products
alert, promotions, and warranty service from EleTab.
Let us know with a customer review.
Love it? Hate it?
EleTab is committed to delivering customer-driven products that
live up to you high standards. We encourage you to write a
review sharing your experierience.
Should you have any issues, please don't hesitate to contact us.
Scan the qr code below for more products from EleTab
For further services:
Send your name and order ID to EleTab_ser[email protected]
Altri manuali per ELTGM01-2
1
Indice
Altri manuali eletab Rack e supporto
eletab
eletab ELTGM02-1 Manuale utente
eletab
eletab ELTGM05-2 Manuale utente
eletab
eletab ELTGM03-2 Manuale utente
eletab
eletab ELTGM01-2 Manuale utente
eletab
eletab ELTGM03-2 Manuale utente
eletab
eletab ELTGM05-1 Manuale utente
eletab
eletab ELTGM01-1 Manuale utente
eletab
eletab ELTGM04-2 Manuale utente
eletab
eletab GM01-1 Manuale utente
