Elgee Power-Vac 632-E Manuale utente
OWNER’S MANUAL
1
Your new machine is the perfect soluon for debris and lier control at factories, warehouses,
stables, sports arenas, amusement parks, and countless other facilies. The Power-Vac’s ability
to clean up to 40,000 square feet per hour will save you me and money!
632-E, 633-E, 634-E, 642-E, 643-E, 644-E
Assembling the Power-Vac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Handle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dolly Installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Deector Installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Filter Bag Installaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hose Assembly and Installaon . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the Oponal Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Maintaining your Power-Vac . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Addional Resources and Contact Informaon. . . . . . . . . . . . . . . . . . 15
Elgee Power-Vac Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . 16
2
Assembling your new Elgee Power-Vac is a snap. Just follow the instrucons on the next few pages and
you’ll be up and running in no me!
Below is an exploded view showing the main components to be assembled. The hardware that is used
is detailed on the next page.
FILTER BAG
LEFT HANDLE LEG
MACHINE BODY
AND POWER PLANT
HANDLE
DOLLY
DEFLECTOR
RIGHT HANDLE LEG
3
• Ratchet wrench with 1/2” socket and extension
• 1/2” Open end wrench
• Rubber mallet
5/16” x 1-1/2” Hex Head Screw (4)
5/16” Locking Hex Nut (has an embed-
ded nylon ring on one side) (4)
5/16” Hex Nut (2)
5/16” Lock Washer (2)
5/16” Flat Washer (4)
5/16” x 1-1/4” Hex Head Screw (2)
4
Aach the Le and Right Handle Legs to the machine body. NOTE: The Right Handle Leg has ve
holes and goes on the right side of the machine (when viewed from the operator’s posion); the
Le Handle Leg has only three holes and goes on the le side. For each leg, use two hex-head
machine screws, at washers, and locking hex nuts as shown in the illustraons below.
5/16” FLAT WASHER (2)
5/16” X 1-1/2” HEX
HEAD SCREW (2)
LEFT HANDLE LEG
(WHEEL NOT SHOWN FOR CLARITY)
5/16” LOCKING HEX NUT (2)
RIGHT HANDLE LEG
5/16” FLAT WASHER (2)
5/16” X 1-1/2” HEX
HEAD SCREW (2)
(WHEEL NOT SHOWN FOR CLARITY)
5/16” LOCKING HEX NUT (2)
5
LEFT HANDLE LEG
RIGHT HANDLE LEG
5/16” FLAT
WASHER (2)
5/16” X 1-1/4” HEX
HEAD SCREW (2)
5/16” HEX NUT (2)
HANDLE
Slide the Handle onto the Right and Le Handle Legs and
aach with two hex-head machine screws, at washers, and
hex nuts as shown in the illustraon. The two holes nearest
the bend must be on the right side of the machine when
viewed from the operator’s posion.
6
Line up the half hole of the Dolly with the machine’s Axle.
Strike the Dolly above the hole with a rubber mallet to snap it into place.
DOLLY
AXLE
WHEEL COLLAR
HALF HOLE ON DOLLY FRAME SNAPS
ONTO AXLE INBOARD OF WHEEL
COLLAR. STRIKE WITH RUBBER
MALLET TO FULLY ENGAGE.
(WHEEL NOT SHOWN FOR CLARITY)
7
Posion the Deector towards the inside of the machine so that its top and boom lips will engage
the channels on the discharge chute.
Use a rubber mallet to force the Deector outward unl it is centered on the discharge chute.
DISCHARGE CHUTE
TOP CHANNEL
ENGAGE THE DEFLECTOR’S
TOP LIP WITH THE TOP CHANNEL
DEFLECTOR
ENGAGE THE DEFLECTOR’S
BOTTOM LIP WITH THE
BOTTOM CHANNEL
BOTTOM CHANNEL
DEFLECTOR IN PLACE
8
Place the neck of the Filter Bag over the
Deector so that it covers the channels
on the machine’s discharge outlet.
Cinch the Filter Bag’s built-in
strap to secure its neck.
Loop each pair of the Filter Bag’s handle straps
around the Handle and fasten the metal clasps
to join them.
9
The next few pages describe the assembly, installaon, and use of the oponal Power-Vac Hose.
. Below is an exploded view showing the
parts included with the kit.
HOSE
BRACKET
HOSE NOZZLE
HOSE CUP
1/4” LOCK WASHER (2)
1/4” LOCK WASHER (3)
1/4” HEX NUT (2)
1/4” HEX NUT (3)
HEX HEAD MACHINE
SCREW, 1/4” x 1-1/4”
HEX HEAD MACHINE
SCREW, 1/4” x 1”
HOSE HANDLE
HOSE CLAMP (2)
5/16” HEX NUT
HOSE
5/16” LOCK WASHER
HEX HEAD MACHINE
SCREW, 5/16” X 1-1/4”
MANUAL HOSE
BAFFLE
Questo manuale è adatto per i seguenti modelli
5
Indice
