Elid EL374 Manuale utente

EL374 Access Control Panel

Technical Manual

(Revision 1.0.1)

ELID SDN BHD

EL374 Access Control Panel

Table of Content

CHAPTE 1 .............................................................................................................................. 1

1 EL374 Access Controller .............................................................................................. 1

1.1 Introduction .......................................................................................................... 1

1.2 Configuration........................................................................................................ 2

1.3 Principle of Operation .......................................................................................... 4

1.4 ID Cards............................................................................................................... 4

1. Normal Operation.................................................................................................

1.6 Timer and Time Zone........................................................................................... 6

1.7 Logging of Activities ............................................................................................. 7

CHAPTE 2 .............................................................................................................................. 9

2. INSTALLATION............................................................................................................. 9

2.1 Introduction .......................................................................................................... 9

2.2 Physical Installation ............................................................................................. 9

2.3 Input /Output Points Installation ......................................................................... 10

2.4 Powering Up Procedures................................................................................... 10

CHAPTE 3 ............................................................................................................................ 13

3. PROGRAMMING MODE............................................................................................ 13

3.1 The Operation of Keypad................................................................................... 13

3.2 Commands......................................................................................................... 14

CHAPTE 4 ............................................................................................................................ 16

4. TIME MENU................................................................................................................ 1

4.1 Set Date / Time .................................................................................................. 16

4.2 Set Timer............................................................................................................ 17

4.3 Set Holiday......................................................................................................... 19

4.4 Set Access Time Zone ....................................................................................... 19

4. Set Miscellaneous Time Zone............................................................................ 21

CHAPTE 5 ............................................................................................................................ 23

5. CARD MENU .............................................................................................................. 23

.1 Add Card Via Reader......................................................................................... 23

.2 Add Card Via Keypad ........................................................................................ 24

.3 Remove Card Via Reader.................................................................................. 2

.4 Remove Card Via Keypad ................................................................................. 26

. Set Code Entry................................................................................................... 26

CHAPTE 6 ............................................................................................................................ 28

. Set-up MENU.............................................................................................................. 28

6.1 Set Unit Number & Baud Rate........................................................................... 28

6.2 Set Door Parameter ........................................................................................... 29

6.3 Set Door Contact Type & Lock Release Time ................................................... 30

6.4 Set Auxiliary Output ........................................................................................... 30

6. Set EL Z ID Code and Customer Code ............................................................ 31

6.6 Power Save ...................................................................................................... 33

6.7 Print Transaction Report and Card Database.................................................... 33

6.8 Backup & Restore .............................................................................................. 34

6.9 Language ........................................................................................................... 34

CHAPTE 7 ............................................................................................................................ 36

.9 SELF-TEST COMMAND ........................................................................................ 3

7.1 Input Test............................................................................................................ 36

7.2 Output Test......................................................................................................... 37

7.3 Serial Port Test................................................................................................... 37

7.4 Keypad Test ....................................................................................................... 38

7. Reader Test........................................................................................................ 38

7.6 Memory Test....................................................................................................... 38

7.7 Hard Reset......................................................................................................... 39

7.8 Test CPU Frequency............................................ Error! Bookmark not defined.

EL374 Access Control Panel Technical Manual

CHAPTE 1

1 EL374 Access Controller

1.1 Introduction

EL374 is Microprocessor controlled equipment that combines access controller, card reader

and keypad in single unit. It is equipped with a 122 X 32 pixels backlit graphical LCD and a

12-key touch sense keypad.

EL374 has the following features:

 Stand-alone operation or networking operation with PC.

 24 timers, each with 2 sets of start-stops.

 10 sets of 8-day time zones (Monday to Sunday plus holiday)

 Stored up to 4000 ID cards (2000 ID with programmable PIN, or 4000 ID with pre-set

PIN)

 Logs 2000 transactions

 Automatic PIN activation by time zone

 Automatic lock release by time zone

 Operation mode: Card only, Card + PIN, PIN.

 Optional EL Z remote relay unit to improve security, with additional 1 sensor input and 1

auxiliary output.

 LAN option using EA792T

 In-circuit firmware update by serial communication.

EL374 Access Control Panel Technical Manual

1.2 Configuration

The drawings below show the basic set-up of an EL374 system. There are 4 configurations

available.

 Stand alone, normal mode

 Stand alone, secure mode

 PC linked, through RS48 of Local Area Network (LAN)

In the standalone mode, all programming is carried out using built-in keypad.

In the PC linked mode, all operations can be controlled from PC running access management

software such as E.WIN or WINPRO or SPHERE.

EL374 Access Control Panel Technical Manual

The first configuration has low security, because the EM lock is connected directly to EL374

and can be tampered with, as EL374 is installed in a non-secure area.

For better security, EL374 should be fitted with an EL Z remote relay unit mounted in a secure

zone as shown in the second diagram.

Note that in this mode, all external devices are connected to EL Z. Furthermore, EL Z

provides an extra input point and extra output point.

There are 3 external devices connected to EL374 (or EL Z, if it is used).

Device Description

Door Sensor Device that can detect whether the door open or shut.

Electric Lock Electrically operated device that can lock or unlock a door depending

on whether electricity is supplied to the device or not.

Exit Push Button Push button switch, which when activated, will unlock the door by

energizing the electric lock.

You need to supply a 12VDC power source with at least 0.7A capacity, excluding the power

consumption of the electric locking device. In most installations, a charger with sealed

lead-acid battery on float charge should be provided, so that the door can continue to work

even when there is power outage. The charger should maintain float charge voltage 13.8V.

There should also be a low-voltage cut off, so that the battery is disconnected from EL374

when voltage falls below 10V. This low voltage cut-off is particularly important if you are using

EM locks. When voltage falls below 10V, EL374 will shut down, and will not read a card

presented, nor will it respond to any command from PC. At the same time, the EM lock will still

be energized, because there is 10V of supply across it. Therefore, the door will be held locked

EL374 Access Control Panel Technical Manual

until battery drains out, or power supply returns.

Elid sells a range of chargers specially made for Access applications.

If EL Z is used, it provides 1 sensor input and 1 auxiliary output. This sensor input may

function as an alarm input or a status input, depending how the auxiliary output is configured.

The auxiliary output point can be programmed as a sensor alarm output, or door open alarm,

or general purpose output, or valid exit output

When configures as sensor alarm output, it will treat sensor input as a alarm point, which can

be armed or disarmed

When configured as a door open alarm output, it will be activated when the door protected by

EL374 is forced open or left open.

When programmed as a General Purpose (GP) output, it can be switched on manually or

automatically by time zone.

When program as Valid Exit output, it will be activated when there is valid exit transaction.

1.3 Principle of Operation

The EL374 system uses cards to unlock a door. Each person eligible to enter the door is

issued with an ID card. The type of ID card used will depend on the type of readers that EL374

is equipped with. Elid offers different models of EL374 fitted with different types of readers.

When a person presents his card to the reader, the card number is read and compared with

the list of ‘valid’ numbers held inside the memory of EL374. If the number is found, EL374 will

check to see whether this particular card user is allowed entry at the particular day. If the

answer is ‘yes’, and the EL374 is configured as card only mode, it will activate the electric lock

to unlock the door. If the EL374 is configured as card + pin mode, then it will wait for the PIN

(Personal Identification Number) to be keyed in. If any of the above 3 tests fail, the door will not

be unlocked.

1.4 ID Cards

As stated in the previous section, encoded ID cards are used as ‘keys’ for opening doors.

Cards can be EM proximity, HID Proximity, Mifare smart cards, depending on the model of

reader you have purchased. However, card format used must conform to the following:

ELID Wiegand Format

These are cards encoded with propriety Elid format.

Standard Wiegand 26-Bit Format

A card with the standard 26-bit Wiegand format will have a customer code in the range 0-127,

and ID number from 0-6 3 . Any card can be assigned as a Master Card. All cards with ID

EL374 Access Control Panel Technical Manual

number larger than 60,000 are automatically treated as Special Cards, and should not be

used.

Free Wiegand Format

The card can be encoded with up to 48 bits, and you can specify any bits, up to maximum of 20

bits as containing the ID number to be read.

For example, you can specify that EL374 reads 40 bits of the card output, and select bits 20 to

40 as the ID number. In this case, the first 20 bits will be ignored, and only bits 20 to 40 are

read.

1.5 Normal Operation

When the EL374 is operating normally, you will see ‘Welcome!’ and the time (HH:MM)

displayed at the LCD display. The first 2 digits indicate the hours and the next 2 digits the

minutes. Time is indicated in 24-hour format. For example, 4 pm is indicated as 16:00. The

‘Welcome!’ which located at the upper row of LCD will blink once every second. This condition

indicates that the equipment is ready to read a card.

Depending on how the EL374 is programmed, entry is granted on the following conditions:-

 Is the card properly read?

 Is the card number in the list of valid cards stored in EL374 memory?

 Is the Access Time Zone correct? In other words, is the card allowed access at this

particular day of the week and this particular time?

 Is the EL374 set to ‘No-Entry’ mode, in this mode, none of the card can access.

 Is the EL374 set to Card + PIN mode? If so, it will check the 4-digit PIN entered

The LCD screen of the EL374 unit will respond to the different situations above with different

displays as detailed below:-

Error ead : The card ID code cannot be read, which may be due to card

damage or use of cards with incompatible format.

Wrong CustCode : Card’s customer code does not match the Controller’s customer

code.

Not enrolled : The number is not found in the memory.

Wrong TimeZone : The number is found in the memory, but the category or time zone

of the card is such that it cannot enter the door at this particular time.

No Entry EL374 is set to “No Entry” mode.

If the card number is found in the memory, and the access time zone is correct. In other words,

the card is allowed entry at this particular time. Then one of the following will take place:-

 If the EL374 is programmed to “Card-only” mode, then the display will show “GO” and

the door is unlocked.

 If the EL374 is programmed to “Card+PIN” mode, then the display will show “Enter

EL374 Access Control Panel Technical Manual

PIN?” requesting the user to key in the 4-digit PIN code. As each number is keyed in,

there will be a “beep” sound and a”*” is displayed. If the code is correctly entered, the

display will show “GO” and the door is unlocked. If the code is wrong, the display will

show “Wrong PIN”, and the door will not open.

When a person wishes to exit, he should push the Exit Push Button. This will activate the

Electric Lock to unlock the door. However, an exit reader can be installed in lieu of push button,

in which case he should present his card at the exit reader. The advantage of putting an exit

reader is that you can tell who has exited the room.

Note that each time the Electric Lock is activated, it does so for a limited time period, (factory

setting is seconds, but can be changed to other duration) after which the door is locked back.

The user should open the door during this period; otherwise the door will be locked again.

1.6 Timer and Time Zone

A powerful feature provided by EL374 is the ability to grant or deny access depending on time.

This is done by setting “Timers” and “Access Time Zone”. A timer has 2 sets of “start” and “end”

times. There are 24 timers in EL374. For example, you may set up the timers as follows:-

Timer # Start Time 1 End Time 1 Start Time 2 End Time 2

1 (Predefined) 00:00 00:00 00:00 00:00

2 (Predefined) 00:00 23: 9 00:00 00:0

3 08:30 12:30 13:30 17:30

4 07:00 19:00 00:00 00:00

07:00 13:00 00:00 00:00

6 07:00 08:00 18:00 19:00

… … … … …

Timer # Start Time 1 End Time 1 Start Time 2 End Time 2

… … … … …

24 13:00 18:00 00:00 00:00

In the above example, Timer 3 is set to be activated between 08:30 and 12:30 for the first

period, and 13:30 to 17:10 for the second period. If this timer is assigned to, say, lock output,

then the door will be open during the 2 periods 08:30-12:30 and 13:30-17:30. The door will be

locked at other times.

In real life, we often need different timers for different day of the week, and if a particular date

happens to be a holiday, we will need a different timer. This is handled by the ‘Access Time

Zone’ command. The Time Zone command allows you to divide your staff into different groups

or categories, each with its own unique set of times to control when entry is granted.

An example of such a requirement for time zone is shown in the table below. Note that the

EL374 Access Control Panel Technical Manual

timers used are those referred ealier.

In this example, staffs are divided into 4 groups:-

 Time Zone 2 is for company chief executives, who may come in at any time, any day.

This is a predefined time zone, and no programming is needed.

 Time Zone 3 is for managers who can come in from 7 am to 7 pm from Monday to Friday,

but can only come in from 7 am to 1 pm on Saturday, and cannot come in on Sunday and

holiday. This is achieved by giving timer 4 for Monday, Tuesday, Wednesday, Thursday

and Friday, and timer for Saturday, and timer 1 for Sunday and holiday.

 Time Zone 4 is for general office staff who can come in only from 8:30 am to 12:30 pm

and from 1:30 pm to :30 pm from Monday through Friday. This is achieved by giving

timer 3 for Monday, Tuesday, Wednesday, Thursday, Friday, and timer 1 for Saturday,

Sunday and holiday.

 Time Zone is for cleaners who can come in only from 7 am to 8 am and 6 pm to 7 pm

on Tuesday.

Timer For

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche