Elite Acoustics A1-58 Manuale utente
WHAT IS IN THE BOX
A1-58 package contains the following:
Elite Acoustics Engineering
A1-58 120W Lithium Battery Powered
Acoustic Ampler with 3 Channels, Mixer,
and 16 digital Eects
Quick Start Guide V1.00
(1) Speaker
(1) 12V AC Power Supply Adapter
NOTE: Due to continuous development and improvements of our products, features and specications are subject to
change without notice. All weights and measures are approximate. Revision Date - Dec 2022.
QUICK START
1. Battery Switch [26] is set to Connect. (Battery Switch to preserve battery life.)
2. Make sure the SPEAKER VOLUME [3] control is down before you turn the POWER [25]
on.
3. Connect the input of your microphone to the MIC IN [15.1]. Or you can connect a ¼” line
input [15]from an instrument [15.2]. You can also connect an additional mono or stereo
[20].
4. Turn on the POWER [25] switch.
5. Turn on your source signal(s) and adjust the volume on the source signal for normal
operation.
6. Turn up LEVEL [16] until there is a solid green light showing “signal”[5] at desired level,
without a red “peak”[5] light, indicating too much signal.
7. Adjust the SPEAKER VOLUME [3] to a comfortable level.
Power LED: BLUE [1]: Indicate unit is ON
+48V LED [2]: Indicates Phantom Power is on
Monitor Output Controls
Speaker Volume [3]: Control speakers’ volume level
Mono [4]: Changes speaker output to Mono sound
Equalizer [6]: Adjust Speaker High, Mid, and Low Frequency response
Peak LED [5]: RED indicate Signal Clip
Signal LED [5]: GREEN indicate Signal
Aux Input/Level [7]: Connect audio source with 1/8” jack from MP3/CD player
Eects Controls
Effects Mix [8]: Amount of effect being applied to Input
Rate/Decay [9]: Controls the duration of the effect
Effects Knob Selector [10]: Select effect of choice
EFX Bypass [11]: Turn effects on or off (When LED is on, the effects are turned off)
Channel 1
EFX Send Level [13]: How much output effect is being sent out
+48V [14]: Phantom Power control
Line In [15]: 1/4” TRS inputs
Level [16]: Gain level control
Mute [17]: Mute channel
Mic In [15.1]: XLR for Microphone Input
Instrument Input [15.2]
Channel 2/3
Level [19]: Gain level control
Left/Right Input [20]: 1/4” TRS Input
EFX Send Level [21]: How much output effect is being sent out
Monitor Output: Connect with extra speakers/monitors
Output Source [22]: Assigns Main Output or Direct Output
Main Output [23]: XLR Output
Power LED: BLUE [1]: Indicate unit is ON
+48V LED [2]: Indicates Phantom Power is on -- for Both Chan 1 and Chan 2.
Monitor Output Controls
Speaker Volume [3]: Control speakers’ volume level
Mono [4]: Changes speaker output to Mono sound
Monitor Equalizer [6]: Adjust Speaker High, Mid, and Low Frequency response
Peak LED [5]: RED indicate Signal Clip
Signal LED [5]: GREEN indicate Signal
Aux Input/Level [7]: Connect audio source with 1/8” jack from MP3/CD player.
Top Panel View
A1-58 - Acoustic Amplifier with Three Channels
Digital Effects and Lithium Battery
ELITE ACOUSTICS
Eects Controls
Effects Mix [8]: Amount of effect being applied to Input, Dry and Wet mix. There is no
EFX if knob is completely on DRY position.
Rate/Decay [9]: Controls the duration of the effect
Effects Knob Selector [10]: Select effect of choice
www.EliteAcoustics.com
Designed, Assembled, & Tested
in California, USA.
A1-58 - Acoustic Amplifier with three Channels,
Digital Effects and Lithium Battery
ELITE ACOUSTICS
ConnectD isconnect
Battery Switch
OnOff
R1 - Bright Cavern
R2 - Dark Cavern
R3 - Bright Hall
R4 - Dark Hall
R5 - Bright Room
R6 - Dark Room
R7 - Bright Plate
R8 - Dark Plate
R9 - Ambience1
R10 - Ambience2
E1 - Echo
E2 - Repeat Echo
ER1 - Echo/Rev1
ER2 - Echo/Rev2
CHO - Chorus
Flange - Flange
A1-58 Effects
Serial number
+9VDC Output
Instr
Mic/Line
Instr
lift
GND
Low
Charging
Low
Charging
Battery Level
Charged
Charged
+12VDC 5A
DC Input
Tips.
+9VDC (500mA) output is Center Positive.
Use to StompMix 4 or GigMix 4-1 digital mixers.
Channel 1
Gain [16]: Gain level control
Mute [17]: Mute channel
EFX Send Level [13]: How much output
effect is being sent out
+48V Phamton Power [14]
Line In [15]: 1/4” TRS inputs Balanced
Mic In [15.1]: XLR for Microphone Input
Balanced
Mic/Line or Instrument Input selection
switch [18]
Instrument Input (15.2)
Instrument Input is recommendated for
Passive Pickups that need high Z and
higher Gain.
+9VDC Output
Instr
Mic/Line
Instr
lift
GND
Instr
Mic/Line
Instr
Battery Switch[38] : Built in Slide Swtich to preserve battery
life.
Connect: Enable battery power when using unit
Disconnect: Disable battery power when storing unit to
preserve battery life
Chanel 2/3
Gain [19]: Gain level control
EFX Send Level [21]: How
much output effect is being
send out
Left/Right Input [20]: 1/4” TRS
Input
Output Source [22]:Assigns
Main Mix Output
or Channel 1 Direct Output
Main Output [23]: XLR Left/Right
Output
GND lift For XLR outputs (24)
lift
GND
The Monitor Right Output (33) allows you to add a secondary active monitor while preserv-
ing the stereo image. The Monitor unit will play the Left Channel content and the secondary
monitor will play the Right Channel. If stereo imaging is not desired, simply engage the
Mono button on the A4-8’s top panel. Note that the Monitor Right Output (33) will not drive a
passive speaker; it is a Line-level output that can drive ampliers or active monitor systems.
Connect Master Speaker Right output (33) to Secondary speaker Chan 3/4 Line input (32).
Set Secondary Speaker Gain (30) to 3 0’clock. Then set Secondary Monitor Level (3) to
balance the Left (Master speaker) and Right (Secondary speaker) channels. EQ on Sec-
ondary Speaker should be FLAT and EFX (11) should be bypassed.
CONNECTING TO ANOTHER SPEAKER FOR STEREO
CONNECTING TO ANOTHER ACTIVE SPEAKER HOUSE PA
FROM DIRECT OUTPUTS OR MAIN MIX OUTPUTS
The XLR output jacks can be used for MAIN MIX outputs (seperate from the Monitor Speaker Out-
put) or Direct Outputs for Chan 1 “Left” (35) and Chan 2 “Right” (35) with Level Control. Switch
(34) control Main (Switch Out) or Direct Out (Switch pressed in).
For Maximum Battery Life
- Recharge after every use
- Use & recharge battery at least once a month
- Do not leave power switch in the “ON”
positionwhen it is not in us e
- Keep unit in a cool, dry place away from extreme
temperatures
- Do not service, modify,or replace the battery
- If the battery fails to charge, contact EliteA coustics
WARNING
Only exchanget he original speaker system
battery with ag enuine EliteA coustics Engineer-
ingr eplacement.E liteA coustics Engineering
cannotg uarantee thes afetya nd compatibilityo f
batteries from otherm anufacturesf or theu se in
operatingt he speaker system.U se of an uncerti-
fied battery may void all warranties.
www.eliteacoustics.com
ELIT EA COUSTICS
Mute
EFX Send
Phase
Mic 1
Line
01 0
Gain
01-0 10 50 3
Notch Filter
-100
Frequency
100 450
High
-15+ 15
Mid
-15+ 15
Low
-15+ 15
Equalizer
Mute
EFX Send
Phase
Mic 2
Line
01 0
High
-15+ 15
Mid
-15+ 15
Low
-15+ 15
Level
01 0
EFX Send
01 0
Left
(Mono)
Right
Monitor
Right
Output
Battery Level
Equalizer
32 1L ow Charge
Gain
01-0 10 50 3
CHAN 1 CHAN 2 CHAN 3/4
EFX
Bypass CHAN 1/2
Mute
Outputs
Output Source
Main Outputs
CHAN 1/2
Direct Output
Level
01 0
Left Right
+48V
On
Off
Power
DC INPUT
12VDC 2A
Connect Disconnect
Battery Switch
Serial Number
Designed, Assembled, & Tested
in California, USA
Charging
Only
TIP - CHAN 1
RING - CHAN 2
For Maximum Battery Life
- Recharge after every use
- Use & recharge battery at least once a month
- Do not leave power switch in the “ON”
positionwhen it is not in us e
- Keep unit in a cool, dry place away from extreme
temperatures
- Do not service, modify,or replace the battery
- If the battery fails to charge, contact EliteA coustics
WARNING
Only exchanget he original speaker system
battery with ag enuine EliteA coustics Engineer-
ingr eplacement.E liteA coustics Engineering
cannotg uarantee thes afetya nd compatibilityo f
batteries from otherm anufacturesf or theu se in
operatingt he speaker system.U se of an uncerti-
fied battery may void all warranties.
www.eliteacoustics.com
ELIT EA COUSTICS
Mute
EFX Send
Phase
Mic 1
Line
01 0
Gain
01-0 10 50 3
Notch Filter
-100
Frequency
100 450
High
-15+ 15
Mid
-15+ 15
Low
-15+ 15
Equalizer
Mute
EFX Send
Phase
Mic 2
Line
01 0
High
-15+ 15
Mid
-15+ 15
Low
-15+ 15
Level
01 0
EFX Send
01 0
Left
(Mono)
Right
Monitor
Right
Output
Battery Level
Equalizer
32 1L ow Charge
Gain
01-0 10 50 3
CHAN 1 CHAN 2 CHAN 3/4
EFX
Bypass CHAN 1/2
Mute
Outputs
Output Source
Main Outputs
CHAN 1/2
Direct Output
Level
01 0
Left Right
+48V
On
Off
Power
DC INPUT
12VDC 2A
Connect Disconnect
Battery Switch
Serial Number
Designed, Assembled, & Tested
in California, USA
Charging
Only
TIP - CHAN 1
RING - CHAN 2
EAE BATTERY & RECHARGING INFORMATION
1. To fully charge a unit –
a. Set Battery Switch to “CONNECT”
b. Turn Power Switch OFF
c. Connect “AC” adaptor to Power Jack.
d. Blue “Charge” LED should be lit, Charge time is about 5-6 hours.
2. When unit is powered with “AC” adaptor, Battery Switch should be in “CONNECT”
position. If unit is always plugged in, it is recommendate to put Battery Swtich in
Disconnected position, but make sure to recharge unit monthly.
3. Battery Switch should be on “DISCONNECT” when unit is packed for transit or unit
is in storage. Make sure battery is fully charged before UNIT is put into storage. We
recommend fully charging the battery at least once each month.
4. Lithium Iron Phosphate (LifePO4) battery lifetime is typically 3 – 4 years depending on
usage.
5. Recharge Battery every month if not in use.
FOR MAXIMUM BATTERY LIFE
• Battery TYPE - LifePO4
• Battery METER indicators -
•
• FULLY CHARGED. - GREEN LED ON (will turn off once unit is in use)
• NORMAL - GREEN ON
• NORMAL and LOW -- Both LEDS are ON less then (about 10% - 25%)
• LOW - RED ON (less then 10%)
• CHARGING - BLUE LED ON. (will turn off when Fully Charged)
•
• For Maximum Battery Life
• - Recharge when battery is low.
• - Drain & recharge battery at least once a month
• - Do not leave power switch in the “ON” position when it is not in use.
• - Keep unit in a cool, dry place away from extreme temperatures
• - Do not service, modify, or replace the battery
• - If the battery fails to charge, contact Elite Acoustics
•
• If unit is always plugged in, it is recommendate to put Battery Swtich in Dis-
connected position, but make sure to recharge unit monthly.
Low
Charging
Low
Charging
Battery Level
Charged
Charged
ABOUT EQ SETTINGS
High – used to add sibilance and crispness to your sound, with the knob at 12:00, there is no
boost or cut to the high frequency content.
Mid – Helps control the clarity of your overall mix and should be adjusted to suit lower or
higher volume performance levels. Boosting the mids helps speech clarity and intelligibility at
lower volumes while cutting the mids produces a more natural sound at higher volumes. The
Mid frequency selection knob allows for a range extending from high LF to low HF. When set
to 12:00 the Mid frequency peak is around 1.2k Hz, with +/- 12dB of boost or cut depending
on the setting of the Mid knob. Here again, with Mid set to 12:00 the mid control is effectively
out of the circuit.
Low – In general, lower volumes can benet from LF boost to help bring out the bass at these
lower settings, but it is usually left at or even slightly cut for high playback levels.
DIGITAL EFX
16 DIGITAL EFX PROGRAMS
•
• There are 16 total Digital EFX programs
• R1 to R10 - REVERB
• E1 and E2 - ECHO
• ER1 and ER2 - Echo and Reverb
• CHO - Chorus
• FLange - Flanger
•
• Program select Encoder (10) is for program change.
• Parameter knob (9) to change rate or delay time for the program that is set.
• Mix knob (8) is to ne turn the amount of EFX you want in output mix.
• EFX can be bypassed by Pressing the bypass switch (9)
• EFX send levels for each channel is set by on the rear panel ( 14, 24, and 31)
that correspond to each channel.
•
TIPS
• Distorted Sound
• 1) Check input level to make sure input Signal Light is in GREEN and not CLIP-
PING RED. Reduce Input by turn down GAIN knob (12, 19). Make sure all EQ
knobs are set to Middle. (FLAT)
• 2) Check Monitor Signal Light is also GREEN and not Clipping. Reduce Speaker
Level by turning Monitor Knob (3), make sure EQ is set to middle (FLAT)
•
• No Sound
• 1) Check LED signal lights. Green means there is Signal on the input.
• 2) Make sure MIX knob is at 12 o’clock position.
• 3) Make sure Channel is un-muted.
• 4) Make sure +48V is on when using a Condenser Mic. Make sure to MUTE
when turning on +48V to prevent loud POP sound.
•
• Battery not Holding Charging
• 1) Power unit off and charge the unit for 24 hours with Battery switch in Con-
nected position. If problem still persist, contact [email protected] for
battery replacement instructions.
•
•
R1 - Bright Cavern
R2 - Dark Cavern
R3 - Bright Hall
R4 - Dark Hall
R5 - Bright Room
R6 - Dark Room
R7 - Bright Plate
R8 - Dark Plate
R9 - Ambience1
R10 - Ambience2
E1 - Echo
E2 - Repeat Echo
ER1 - Echo/Rev1
ER2 - Echo/Rev2
CHO - Chorus
Flange - Flange
Indice
Altri manuali Elite Acoustics Amplificatore
