Elite SIM-8000 Manuale utente
INSTALLATION
MANUAL
SIM/SIK/SI-8000
IP Intercom System
ELITE
SIM/SIK/SI-
8000Series
IP Intercom System
QUICK START GUIDE
CONTENTS
Introduction
Specifications and Package Contents 1
Dimensions 2
Installation and Connections 3
System Diagram 5
Basic Functions and Operation 6
Factory Reset 7
I.
Detect and Verify Network Settings
Search for devices with CVT Upgrade Tool 8
Getting to a Command Prompt in Windows
Verify your computer’s network settings 9
Compare your computer’s IP address with
your SIM’s IP address
II.
Accessing and Configuring the Setup Interface
Launching the user interface
10
Enter log in credentials
LAN Settings
11
Device Settings
12
Access Settings
13
SIP Settings
14
Forward Account Settings
15
External Module Settings
17
Advanced Settings
Phone Book
18
Default, Restore and Backup
Log Out
19
Support and Warranty (Back)
1
SPECIFICATIONS
SIM/SIK/SI-8000Series
IP Intercom System
PACKAGE CONTENTS
CPU 350 MHz
RAM DDR2 (1 GB x 2)
Flash 2 GB
Power
12V DC
IP Rating IP 66
Rated Power
6W
Standby Power Consumption 6W
Operating Temperature -5ºF ~ 131ºF
Relative Humidity 20% ~ 93%
Screen 3.5” Dot Matrix
Dimensions H 14.75”
W 6.5”
D 2”
Model: SIM-8302
Allen
Wrench
Seal
Ring
Waterproof jacket1
Waterproof jacket2
Cover
Waterproof jacket3
Installation screws Network port seal ring
Model SIK-8000 series
2
6.5”
Camera
LEDs
Speaker
Display
Digital
Keypad
14.75”
13.75”
Microphone
Card
Reader
5.5”
Flush Mount Box
Dimensions
2”
3
Installation Electrical
Exit/Door Detector
Exit/Door Detector Door Detector
Sense Switch
Power/Unlock Signal Output
Outdoor panel power interface
connects with 12V DC power. Unlock
signal input connected with unlock
module.
4
RS485 RJ45 Pin Out: T-568B
Enable to connect equipment with RS485 interface.
RS485 interface enables to output 12V/100mA power.
+12V is not needed to wire if it is unused.
RS485 Interface RS485 Equipment
5
CAT5e
EX-BUT1
EX-BUT2
GND
+12V
NC
COM
DC
+
+12V
GND
COM
NC
NO
CTRL
Network switch
Exit button
Lock
Flat camera/
Outdoor panel/
Help station
Power(UPS-DP)
Waterproof CAT5 Cable
Plug
Hole
l
Drain hole: 20mm
60mm
181mm
104mm
SIK-8000 series
6
Instruction
Center: 0000 + #
Call: RoomNo + #
Unlock: # + PSW + #
Name:
▲
or
▼
Basic Operation Basic Functions
Calling Indoor Monitor
•
Input floor and room number (at least 3 digits),
then press # to confirm. If you do not press pound
the unit will automatically call after 2 seconds.
•
You can also make a call by searching through
the phone book. To search the phone book,
press the up or down arrow on the keypad,
then press # once you have found the person
you wish to call
•
If the indoor monitor you are trying to reach is
unavailable, the outdoor panel will display “Busy”,
then auto return to standby mode.
•
Press the ✱ button to end communication
at any time during the call
Calling Management Center
•
Dial “0000” then press # to call
the management center
•
If the management center is busy or unavailable,
the outdoor panel will display “Busy”,
then auto return to standby mode.
•
Press the ✱ button to end communication
at any time during the call.
•
Video intercom with indoor
monitor & management center
•
ID card reader -
Supports a maximum of 10,000 cards
•
Access password unlocking
•
Supports standard SIP protocol
to communicate with IP phones
and SIP software
•
Phone book search and direct dial
Unlocking the Door
1. Unlocking by Access Password
•
Press the # key, enter the access password
(default is 000), then press the # key
to confirm
2. Unlocking by IC/ID card
•
Hold the IC/ID card up against the
card reader area of the SIM Intercom
Front Display
Call Guard / Management
Call a room directly
(e.g. 1111#) Unlock door from keypad
(e.g. #123456#)
Search Directory
7
Reset SIM unit to Factory Default Settings
1.
Press # key twice and type in the
default password: 123456. This will take you
to menu settings
2.
Select the Default menu, then enter into the
Default Settings menu
3.
Press 1 to indicate that all settings will be
back to Factory Default Settings,
press
#
to confirm
Access Control Card Reader Section
There are two ways to delete the card information:
1.
If you registered the card via Management Software,
you can delete the card information in the software
as well
2.
If you registered the card via SIM panel, you can
reset the SIM to Factory Default Settings to
delete the card information
8
1 Detect Door Station & Verify Network Settings
1-1
Connect a 12V DC power supply to your
SIM/MDU, then connect your SIM/MDU to your
switch or router via CAT5e or CAT6, then launch
the CVT Upgrade Tool. Click on Search to find
the IP address of your SIM/MDU intercom.
By default, the address is 192.168.1.200.
1-2
Verify your computer’s LAN settings via
Command Prompt
The easiest way to open Command Prompt on
a Windows machine is to press Win+R on your
keyboard. Hold the Windows key down and then
press R.
In the Run window, type “cmd” then hit OK.
This will open Command Prompt
Device ID
IP address
MAC address
Questo manuale è adatto per i seguenti modelli
2
Indice
