Eliwell ICPlus 915 Manuale utente

ICPlus 915

Electronic controller with 2 intervention points

USER INTERFACE

ICPlus 915

KEYS

Press and release

Scroll menu items

Increases values

Press for at least 5 sec

Function can be configured by the user (H31)

STAND-BY (ESC)

Press and release

Returns to the previous menu level

Confirms parameter value

Press for at least 5 sec

Function can be configured by the user (H33)

DOWN

Press and release

Scroll menu items

Decrease values

Press for at least 5 sec

Function can be configured by the user (H32)

SET (ENTER)

Press and release

Displays alarms (if active)

Opens Machine Status menu

Confirm commands

Press for at least 5 sec

Opens Programming menu

ICONs

Decimal Point Temperature

Permanently on: decimal point Permanently on: displays a temperature

Flashing: Soft Start active Flashing: reduced set active, displays

a temperature or no unit of

measure selected

Off: otherwise

Pressure Humidity

Permanently on: displays a pressure Permanently on: displays a humidity

Flashing: reduced set active and displays

a pressure

Flashing: reduced set active and displays

a humidity

Relay OUT1 Relay OUT2

Permanently on: OUT1 output active Permanently on: OUT2 output active

Flashing: a delay, a protection or a locked

start-up

Flashing: a delay, a protection or a locked

start-up

Off: otherwise Off: otherwise

Alarm NOTE:

When switched on, the device performs a Lamp Test; the

display and LEDs will flash for several seconds to check that

they all function correctly.

Permanently on: alarm active

Flashing: alarm acknowledged

Off: otherwise

NTC/PTC MODEL

CONNECTIONS INPUT/OUTPUT CHARACTERISTICS

Display range:

NTC: -50...110°C (-58...230°F)

PTC: -50...140°C (-58...302°F)

on display with 3½ digits + sign

Digital input 1 digital voltage free input

Analogue input 1 NTC or 1 PTC

(selectable by parameter H00)

Serial TTL for connection to Copy Card or Televis/

Modbus remote control systems

Digital outputs OUT1: 1 SPDTrelay 8(4)A250Va

OUT2: 1 SPST relay 8(4)A 250 Va

Buzzer output only on models where this is provided

Measurement range -50 ... 140°C (-58 ...284°F)

Accuracy better than 0.5% of end of scale +1 digit

Resolution 0.1°C (0.1°F up to +199.9°F; 1°F over)

NTC/PTC - 12V, 12-24V

D.I.

Supply

Pb1

OUT1 OUT2

1 2 3 4 5 7 8 9 10 11 12

NTC/PTC - 24V, 115 V, 230 V

D.I.

Supply

Pb1

OUT1 OUT2

1 2 3 4 5 6 7 9 10 11 12

TERMINALS

1-2-3 regulator relay OUT1 *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.

4-5 regulator relay OUT2 9-11 Probe Pb1 Input

*6-7 Power supply 24Va, 115Vaand 230Va.9-12 Digital Input (D.I.)

ATTL input for Copy Card and TelevisSystem connection * depends on model

V/I MODEL

CONNECTIONS INPUT/OUTPUT CHARACTERISTICS

Display range:

-199...199 (ndt = n)

-199.9...199.9 (ndt = y)

-1999...1999 (ndt = int)

on display with 3½ digits + sign

Digital input 1 digital voltage free input

Analogue input

1 V/I (0-1V, 0-5V, 0-10V, 0...20mA, 4...20mA)

(selectable by parameter H00)

Maximum load: - current = 100 Ω

- voltage = 20 kΩ

Serial TTL for connection to Copy Card or Televis/

Modbus remote control systems

Digital outputs OUT1: 1 SPDTrelay 8(4)A 250 Va

OUT2: 1 SPST relay 8(4)A 250 Va

Buzzer output only on models where this is provided

Measurement range -1999 ... 1999

Accuracy better than 0.5% of end of scale +1 digit

Resolution 1 or 0.1 digit according to settings

V/I - 12V, 12-24V

+12V

+ +−

Supply

OUT1 OUT2

1 2 3 4 5 7 8 9 10 11 12

V/I - 24V, 115V, 230V

+12V

+ +−

Supply

OUT1 OUT2

1 2 3 4 5 7 9 10 11 126

TERMINALS

1-2-3 regulator relay OUT1 *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.

4-5 regulator relay OUT2 *9-10-12 Voltage input (9=GND; 10=”+”; 12=12V)

*6-7 Power supply 24Va, 115Vaand 230Va.*9-11-12 Current input (9=GND; 11=”+”; 12=12V)

ATTL input for Copy Card and TelevisSystem connection * depends on model

PT100/Tcj-Tck MODEL

CONNECTIONS INPUT/OUTPUT CHARACTERISTICS

Display range:

PT100: -150...650°C

TcJ: -40...750°C

TcK: -40...1350°C

on display with 3½ digits + sign

Digital input 1 digital voltage free input

Analogue input 1 PT100 or 1 TcJ / Tck

(selectable by parameter H00)

Serial TTL for connection to Copy Card or Televis/

Modbus remote control systems

Digital outputs OUT1: 1 SPST relay 8(4)A 250 Va

OUT2: 1 SPST relay 8(4)A 250 Va

Buzzer output only on models where this is provided

Measurement range -150 ... 1350°C (-238 ...2462°F)

Accuracy see ‘Pt100/TcJ/TcKmodels’ table

Resolution see ‘Pt100/TcJ/TcKmodels’ table

PT100/Tcj-Tck - 12V, 12-24V

D.I.

Supply

Pb1

+−

OUT2

1 2 3 4 6 7 8 9 10 11 12

OUT1

PT100/Tcj-Tck - 24V, 115V, 230V

D.I.

Supply

Pb1

+−

OUT2

1 2 3 4 5 6 8 9 10 11 12

OUT1

TERMINALS

1-2 regulator relay OUT1 8-9 Digital Input (D.I.)

3-4 regulator relay OUT2 *10-11-12 Probe PT100 input - 3 wires (Pb1)

*5-6 Power supply 24Va, 115Vaand 230Va.*11-12 TcJ/TcK input

*6-7 Power supply 12Va/c and 12-24Va/12-36Vc.

ATTL input for Copy Card and TelevisSystem connection * depends on model

PT100/Tcj-Tck MODELs

PT100: ACCURACY: 0.5% for whole scale + 1 digit

0.2% from -150 to 300°C

RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond

TcJ: ACCURACY: 0.4% for whole scale + 1 digit

RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond

Tck: ACCURACY: 0.5% for whole scale + 1 digit

0.3% from -40 to 800°C

RESOLUTION: 0.1°C (0,1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond

MOUNTING - DIMENSIONS

The device is designed for panel mounting. Drill a 29x71 mm hole and insert the instrument; secure it with the special brackets provided.

Do not install the instrument in damp and/or dirty places; in fact, it is suitable for use in places with ordinary or normal levels of pollution.

Keep the area around the instrument cooling slots adequately ventilated.

74 mm

32 mm

29 mm

71 mm

70 mm

59 mm

EWPA-EWHS PROBE CONFIGURATION

EWPA 007/030 2 wires / Transducer

Transducer

brown

white

9101112

EWHS 304/314 3 wires

Probe

GND (only EWHS314)

V+

RH/T

9101112

EWHS 284 2 wires

Probe

brown

blue

9101112

EWHS 314 4 wires (V-I model)

Probe

GND

V+

GND

ICPlus

CPlus 2

91011129101112

ACCESSING AND USING THE MENUs

The resources are organized into 2 menus which are accessed as follows:

• ‘Machine Status’ menu: press and release the key.

• ‘Programming’ menu: hold down the key for 5 seconds.

Either do not press any keys for 15 seconds (timeout) or press the key once, to confirm the last value displayed and return to the previous

screen.

PASSWORD

Password ‘PA1’: used to access User parameters. The password is not enabled by default (PS1=0).

To enable it (PS1≠0): press and hold for longer than 5 seconds, scroll through the parameters using and until you see the label

PS1, press to display the value, modify it using and , then save it by pressing or . If enabled, it will be required in

order to access the User parameters.

Password ‘PA2’: used to access Installer parameters. The password is enabled by default (PS2=15).

To modify it (PS2≠15): press and hold for longer than 5 seconds, scroll through the parameters using and until you see the

label PA2, press , set the value to ‘15’ using and , then confirm using . Scroll through the folders until you find the label

diS and press to enter. Scroll through the parameters using and until you see the label PS2, press to display the value,

modify it using and , then save it by pressing or .

The visibility of ‘PA2’ is as follows:

1) PA1 and PA2 ≠ 0: Press and hold for longer than 5 seconds to display PA1 and PA2. It will then be possible to decide whether to

access the User parameters (PA1) or the Installer parameters (PA2).

2) Otherwise: The password PA2 is amongst the level1 parameters. If enabled, it will be required when accessing the Installer

parameters; to enter it, proceed as instructed for password PA1.

If the value entered is incorrect, the label PA1/PA2 will be displayed again and the procedure will need to be repeated.

MACHINE STATUS MENU

Access the Machine Status menu by pressing and releasing the key. If no alarms are active, the ‘SEt’ label appears.

Use the keys and to scroll through all the folders in the menu:

- AL:alarms folder (only visible if an alarm is active);

- SP1:Setpoint 1 setting folder;

- SP2:Setpoint 2 setting folder;

- Pb1:probe 1 - Pb1 folder;

Setting the Setpoint: To display the Setpoint value press the key when the ‘SEt’ label is displayed.

The Setpoint value appears on the display. To change the Setpoint value, press the and keys within 15

seconds. Press to confirm the modification.

Displaying probes: When label Pb1 is present, press the key to view the value measured by the corresponding probe (NOTE:

the value cannot be modified).

PROGRAMMING MENU

To access the ‘Programming’ menu, press the key for more than 5 seconds. If specified, an access PASSWORD will be requested: ‘PA1’ for

User parameters and ‘PA2’ for Installer parameters (see ‘PASSWORD’ paragraph).

User Parameter: When accessed, the display will show the first parameter (e.g. ‘diF’). Press and to scroll through all the parameters on

the current level. Select the desired parameter by pressing . Press and to modify it and to save the changes.

Installer Parameter: When accessed, the display will show the first folder (e.g. ‘CP’). Press and to scroll through the folders on the

current level. Select the desired folder using . Press and to scroll through the parameters in the current folder and select the

parameter using . Press and to modify it and to save the changes.

NOTE: Make sure you switch the instrument off and on again each time the parameter configuration is changed, in order to prevent mal-

functioning in the configuration and/or timing in progress.

Indice

Altri manuali Eliwell Controllori

Eliwell

Eliwell EWDR 981 Manuale utente

Eliwell

Eliwell IC 915 NTC/PTC Manuale utente

Eliwell

Eliwell ID 985 Manuale utente

Eliwell

Eliwell ID 961 Manuale utente

Eliwell

Eliwell IWP 760 LX Manuale utente

Eliwell

Eliwell EWCM 4120 Manuale utente

Eliwell

Eliwell ID 985 E Manuale utente

Eliwell

Eliwell IC 915 NTC/PTC Manuale utente

Eliwell

Eliwell IC 912 Manuale utente

Eliwell

Eliwell ECH 200BD "Adaptive" Manuale utente

Eliwell

Eliwell ICPlus 902 Manuale utente

Eliwell

Eliwell EWPlus 971 Manuale utente

Eliwell

Eliwell IDplus 961 Manuale utente

Eliwell

Eliwell ID 983LX HACCP Manuale utente

Eliwell

Eliwell ID 971 Manuale utente

Eliwell

Eliwell FREE Panel EVP 3300/C Manuale utente

Eliwell

Eliwell EWCM 8900 Manuale utente

Eliwell

Eliwell IC 912 Pt100-TC Manuale utente

Eliwell

Eliwell EZ-HT Manuale utente

Eliwell

Eliwell EWHT 1800LX Manuale utente

Eliwell

Eliwell IC 912 Series Manuale utente

Eliwell

Eliwell IC 912 LX Pt100 R Manuale utente

Eliwell

Eliwell EW961 Manuale utente

Eliwell

Eliwell EWPC 961/S Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente