Elo TouchSystems ET3201L Manuale utente
USER MANUAL
Elo Touch Solutions
ET3201L 32” Interactive Digital Signage Touchmonitor
ET4201L 42” Interactive Digital Signage Touchmonitor
ET7001L 70” Interactive Digital Signage Touchmonitor
Interactive Digital Signage Computer Module
SW601990 Rev A
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 1 of 32
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 2 of 32
Copyright © 2012 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, including, but not limited to, electronic,
magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its affiliates
(collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo to
notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo (logo), Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch are trademarks of
Elo and itsAffiliates. Windows is a trademark of Microsoft Corporation.
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 3 of 32
Table of Contents
Chapter 1 - Introduction ........................................................................... 4
Chapter 2 – Unpacking.............................................................................. 5
Chapter 3 – Touchmonitor Installation................................................ 7
Chapter 4 – Computer Module Installation........................................ 9
Chapter 5 – Mounting................................................................................ 13
Chapter 6 – Operation............................................................................... 16
Chapter 7 – Technical Support............................................................... 26
Chapter 8 – Safety & Maintenance........................................................ 27
Chapter 9 – Regulatory Information ................................................... 29
Chapter 10 – Warranty Information....................................................... 31
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 4 of 32
Chapter 1 - Introduction
Product Description
Your new Interactive Digital Signage Touchmonitor combines Elo Touch Solutions reliable
performance with the latest developments in touchscreen technology and display design. This
combination of features creates a natural flow of information between a user and the
touchmonitor.
This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor, digital signage
LCD panel to provide superior display performance. Its Full HD resolution of 1920x1080 is
suitable for displaying graphics and images. Other features that enhance this LCD monitors
performance are Plug & Play compatibility, built-in speakers and headphone output capability, a
remote for on screen display (OSD) controls, and a family of Digital Signage Computer
Modules.
The Computer Modules are designed to slide into a bay on the rear of the monitor, without any
effect on the monitors form factor or requiring any extra cabling, turning your Interactive Digital
Signage TouchMonitor into an Interactive Digital Signage All-In-One TouchComputer.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit and prevent risks to user safety. See Chapter 8 for more
information on touchmonitor safety.
For your health and safety, it is strongly recommended that at least two people handle, lift,
and/or move these touchmonitors.
This manual contains information that is important for the proper setup and maintenance of the
Interactive Digital Signage Touchmonitor and optional Computer Module. Before setting up and
powering on your new touchmonitor and computer module, read through this manual,
especially the Installation, Mounting, and Operation chapters.
Chapter 2 – Unpacking
Unpacking the Touchmonitor
To unpack the touchmonitor, follow these steps:
1. The carton should be oriented in the manner according to its labeling. The hinged plastic
locks should be at the ‘bottom’.
2. Open and remove all 4 hinged plastic locks. There are 6 hinged plastic locks for the 7001L
unit.
3. Once the locks are removed, lift the cartons top lid off the bottom frame.
4. With the top lid removed, you now have access to the touchmonitor and the included
accessories.
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 5 of 32
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 6 of 32
Note: For your health and safety, it is strongly recommended that at
least two people handle, lift, or move these touchmonitors. Elo
recommends safe lifting techniques as described in OSHA/NIOSH
Guidelines.
Check that the following items are present and in good condition:
Touchmonitor
User Manual CD
Quick Install Guide
Cables
oHDMI, USB, North America power, Europe/Korea power, U.K. power, Argentina power,
Taiwan power, China power, Korea power, Japan power, & Japan 3pin-2pin adapter
Cable cover screws will be attached to the cable cover.
Unpacking the Digital Signage Computer Module
Open the box.
Check that the following items are present and in good condition:
Digital Signage Computer Module
Quick Install Guide
Cable Cover
User Manual CD
Chapter 3 - Touchmonitor Installation
Connector Panel & Interfaces
Remove the cable cover on the bottom rear (when viewed in landscape orientation) to access
the touchmonitors connector panel.
Pictures of the connector panel and interfaces. The OSD connection is in red.
3201L/4201L/7001L
Images of monitor back I/O ports with OSD remote
Touchmonitor Connections to an External Computer
1. Connect the HDMI cable between the monitor and the video source.
2. Connect the USB touch cable between the monitor and the PC.
3. Connect the remote On-screen Display (OSD) via the remote OSD connector seen in red
above
4. Select the correct power cable for your region. Connect it between the AC power source
and the touchmonitors POWER IN connector.
5. The touchmonitor ships in an ON state. Use the remote OSD to access the On Screen
Display Menu.
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 7 of 32
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 8 of 32
Installing the Touchscreen Technology Software Drivers
Elo Touch driver software installation is required for your IDS 01 series touchmonitor in order to
utilize all of the features that are available through the Elo Tray.
Note: Optical Touchmonitors are capable of working independent of the Elo touch driver, but the
Elo Touch features will not be available. It is recommended to install the Elo Touch driver in
order to maximize your Elo Touchmonitor.
Visit the Elo Touch Solutions website www.elotouch.com for:
Updates to the Elo touch driver
Additional touch driver information
Detailed touch driver installation guides
Touch drivers for other operating systems
Chapter 4
Computer Module Installation
Installation
1. Use a Phillips head screwdriver to remove the access cover plate on the back of the
touchmonitor.
2. Slide the Computer Module all the way into the bay until it snaps into place.
3. Tighten the thumbscrews to secure the computer module inside the bay.
a. If any cables are connected to the computer module, a cable security cover is
included with the computer module kit. Install it by attaching the mounting clip
and bracket as shown in the user guide for the computer module and then
fastening the thumbscrews on the cover.
Connector Panel & Interfaces
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 9 of 32
Touchmonitor & Computer Module Connections
1. Press and hold the touchmonitors power button for 2 seconds to turn on the Computer
Module.
User Manual– Interactive Digital Signage
SW601990 Rev A, Page 10 of 32
Altri manuali per ET3201L
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Elo TouchSystems Schermo tattile
Elo TouchSystems
Elo TouchSystems 3243L Manuale utente
Elo TouchSystems
Elo TouchSystems 3239L Manuale utente
Elo TouchSystems
Elo TouchSystems 2270L Manuale utente
Elo TouchSystems
Elo TouchSystems 1515L Manuale utente
Elo TouchSystems
Elo TouchSystems 2020L Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems E421137 Manuale utente
Elo TouchSystems
Elo TouchSystems Z30POS Stand Manuale utente
Elo TouchSystems
Elo TouchSystems 1725C Series Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems 1528L Manuale utente
Elo TouchSystems
Elo TouchSystems ET17 XXL Series Manuale utente
Elo TouchSystems
Elo TouchSystems 1919L Manuale utente
Elo TouchSystems
Elo TouchSystems 1919L Manuale utente
Elo TouchSystems
Elo TouchSystems 1929LM Manuale utente
Elo TouchSystems
Elo TouchSystems 1928L Manuale utente
Elo TouchSystems
Elo TouchSystems ET1517L Manuale utente
Elo TouchSystems
Elo TouchSystems 1739L Manuale utente
Elo TouchSystems
Elo TouchSystems 1900L Manuale utente
Elo TouchSystems
Elo TouchSystems 2201 Manuale utente
Elo TouchSystems
Elo TouchSystems B-series Manuale utente
Elo TouchSystems
Elo TouchSystems 2440L Manuale utente
