ELRO AG40SR11B Manuale di riferimento

INTRODUCTION ELRO OUTDOOR SOLAR SIREN AG40SR11B:

The Outdoor Solar Siren AG40SRB11B is designed for use with the ELRO HOME ALARM SYSTEM AG4000.

Outdoor Siren:

The siren will emit loud piercing sound when activated. It also has tamper detection features to detect unauthorized

attempts to forcibly remove it from the wall. It features periodic blinking LED to deter intruders.

Installing your Outdoor Solar Siren:

Open the siren by removing its back cover. Then remove the cover of the control box to reveal the control box

underneath.

Inside the control box:

DIP switch setting:

Set the DIP switches to the desired setting. Then connect up the 9V battery followed by the rechargeable battery.

Press the tamper switch and the front LED will flash.

Switch

setting

Siren

Period Siren

on/off Beep

on/off Not used

DIP1

(left most)

DIP2 DIP3 DIP 4-6

ON 15 mins Siren on Beep on Factory

use only

OFF 3 mins Siren off Beep off

Learning LED

Learning Key

DIP switches

1 - 6 (left to right)

6V 1.2Ahr

rechargeable

battery

9V initial power

up battery

Control Box –

hidden under

water proof cover

(below)

Control

box

cover

Tamper

switch

Adding the HOME Outdoor Siren to the Home Alarm System AG4000:

The Alarm Panel itself has a set function that has the default setting of Wireless Siren (Indoor and Outdoor) as

“Disabled”. For the Siren to be paired successfully this need to be changed to ‘Enable’.

The way of doing this is as follows:

Press PIN + 04 + PARM key to enable the wireless siren for pairing function.

After this, the user will see the number 0 on the panels keypad light up, this indicates that the Panel / Siren is

ready for pairing.

IMPORTANT

If the number 0 doesn’t light up, please press digital number 0 + PARM to enable & save the pairing function.

1. Set the alarm panel to Disarm mode.

2. On the siren, press the learning key for more than 3 seconds and release. The Learning LED will flash

repeatedly once every second.

3. Within 30 seconds, on the alarm panel, enter the PIN + DISARM Key.

4. Refer to table below for binding results:

Binding outcome

Indicator on Siren

Status

Successful

LED

Learning LED blink once

Sound

Beep once

Failed

LED

Learing LED flash 3 times

Sound

Beep rapidly 3 times

Mounting the Outdoor Siren:

Mount the siren on a wall outside the home :

- in a position that is clearly visible and at a height which is inaccessible to an intruder.

- where it receives sufficient sunlight

- on a flat surface so that the rear tamper switch is not easily activated.

- at least 1 meter away from any external or internal metalwork which can affect its radio transmission

Use the back plate as a template to mark the mounting holes on the wall. Drill the position of the mounting holes.

Fix the back plate to the wall using the plastic wall plugs and fixing screws provided.

Once the back plate has been secured, attach the main unit down onto the back plate and fasten the screw at the

base. Note: removing the main unit from its back plate will cause the Tamper alarm to sound. Quickly disarm the

alarm panel if this happens.

Operating the Indoor Siren:

Disarm

When the alarm panel is set to Disarm the siren will emit two beeps.

Alarm

Whenever the alarm panel is triggered or when the siren is removed from the wall, the siren will sound along with

flashing LED.

Low Battery

When battery level becomes low, the red strobe LED will flash at 20 second intervals. Replace the batteries as

soon as possible.

Siren Enable/Disable

The siren can be Enabled/Disabled from the alarm panel. When siren is disabled, it can be safely removed from its

mounting without causing it to sound when changing the batteries.

1. Set the alarm panel to Disarm mode.

2. Enter the PIN + 03 to enter Test Mode

3. Press 8Key for more than 3 seconds to toggle between Enable and Disabled. Listen to the siren beeps :

- Enable : beeeeep – beep - beep

- Disable : beep – beep – beeeeep

4. Press Disarm key to exit Test mode

IMPORTANT WARNING:

This package can contain small parts and or material which can be dangerous for small children! Be aware

of this, and keep this away from small children!

For more information about the ELRO HOME ALARM SYSTEM AG4000 visit www.elro.eu

SPECIFICATIONS

Battery Type

6V 1.2Ah Lead acid battery x 1

Loudness

Typically 105dB@1m

Altri manuali ELRO Sistema di sicurezza

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente