Elsner elektronik 71162 Guida

Installation and Adjustment

KNX eTR Light

Button for Temperature Control

and Light

KNX eTR 205 Light

Item numbers

71160 (white), 71162 (black)

KNX eTR 206 Light

Item numbers

71170 (white), 71172 (black)

1 Contents

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

KNX eTR 205/206 Light push button • from application 1.0

Version: 12.12.2022 • Technical changes and errors excepted.

1. Safety and operating instructions ....................................................... 3

2. Description ........................................................................................... 3

2.0.1. Area function ................................................................................................. 4

3. Commissioning .................................................................................... 5

3.1. Addressing of the device at the bus ....................................................................... 5

4. Display and operation at the device .................................................... 6

4.1. Adjust room temperature (using the example KNX eTR 205 Light) .................... 6

5. Transmission protocol ......................................................................... 9

5.1. List of all communication objects ........................................................................... 9

6. Setting the parameters ...................................................................... 13

6.1. Behaviour on power failure/ restoration of power .............................................. 13

6.2. General settings ..................................................................................................... 13

6.3. Temperature measured value ............................................................................... 13

6.4. Temperature threshold values .............................................................................. 14

6.4.1. Threshold value 1, 2 ................................................................................... 14

6.5. Temperature PI controller ...................................................................................... 16

6.5.1. Heating control stage 1/2 ........................................................................... 22

6.5.2. Cooling control stage 1/2 ........................................................................... 24

6.5.3. Fan Coil Control .......................................................................................... 26

6.6. LEDs ......................................................................................................................... 27

6.7. Buttons .................................................................................................................... 28

6.7.1. Light 1 / 2 ..................................................................................................... 28

6.8. Logic ........................................................................................................................ 29

6.8.1. AND logic outputs 1/2 and OR logic outputs 1/2 ...................................... 29

6.8.2. OR LOGIC connection inputs ..................................................................... 31

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

3 Safety and operating instructions

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

1. Safety and operating instructions

Installation, testing, operational start-up and troubleshooting should

only be performed by an authorised electrician.

CAUTION!

Live voltage!

There are unprotected live components inside the device.

• Inspect the device for damage before installation. Only put undamaged devic-

es into operation.

• Comply with the locally applicable directives, regulations and provisions for

electrical installation.

• Immediately take the device or system out of service and secure it against un-

intentional switch-on if risk-free operation is no longer guaranteed.

Use the device exclusively for building automation and observe the operating instruc-

tions. Improper use, modifications to the device or failure to observe the operating in-

structions will invalidate any warranty or guarantee claims.

Operate the device only as a fixed-site installation, i.e. only in assembled condition and

after conclusion of all installation and operational start-up tasks, and only in the sur-

roundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

For information on installation, maintenance, disposal, scope of deliv-

ery and technical data, please refer to the installation instructions.

2. Description

The KNX eTR 205/206 Light push button has touch-sensitive buttons with which

functions can be called up in the KNX building bus system. The glass surface is printed

with areas for setting the temperature and light. LEDs are integrated in these areas and

their behaviour can be adjusted.

A temperature sensor is integrated into KNX eTR 205/206 Light. An external tem-

perature reading can be received via the bus and processed with its own data to create

a total temperature (mixed value).

The KNX eTR 205/206 Light has a PI controller for heating and cooling. The setpoint

temperature can be changed using the "+" and "-" touch buttons.

Communication objects can be linked via AND and OR logic gates.

Functions:

•Operating zone for temperature control with 2 areas (warmer, cooler)

4 Description

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

•LEDs can be set. All LEDs Off, all LEDs as ambient lighting, all LEDs

individually controllable

•Area function when touching two or more push buttons. Can be configured

as switch, selector switch, as 8 or 16 bit encoder or for scenario recall

•Temperature measurements. Mixed value from own measured value and

external values (proportion can be set by percentage), output of minimum and

maximum values

•PI-controller for heating (one or two-level) and cooling (one or two-level)

according to temperature. Regulation according to separate setpoints or basic

setpoint temperature

•2 AND and 2 OR logic gates each with 4 inputs. 8 logic inputs (in the form

of communications objects) can be used as inputs for the logic gates. The

output from each gate can be configured optionally as 1-bit or 2 x 8-bit

Additional functions KNX eTR 205 Light:

•1 operating zone for light with 2 areas (switching/dimming with short/long

distinction)

Additional functions KNX eTR 206 Light:

•2 operating zones for light with 2 areas (switching/dimming with short/long

distinction)

2.0.1. Area function

If the area function in ETS has been activated, another function is available alongside

the regular key functions. This is triggered by touching multiple keys, e.g. if you touch

the sensor with the palm of your hand.

Using the area function

If a key is pressed and another (different) key is touched within 0.2 seconds, the action

set in the ETS is performed for the area operation (See Fig. 1 a) and b)). The keys are

then blocked for 0.5 seconds.

Using the normal key function

If a key is pressed and no other key is touched within 0.2 seconds, the normal key

function is enabled/provided for 5 seconds (See Fig. 1 c) and d)). This is extended for 5

seconds with each push of the button.

5 Commissioning

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

If the area function in the ETS is disabled, the keys can be used normally at any time.

3. Commissioning

Configuration is made using the KNX software as of ETS 5. The product file can be

downloaded from the ETS online catalogue and the Elsner Elektronik website on

www.elsner-elektronik.de in the “Service” menu.

After the bus voltage has been applied, the device will enter an initialisation phase last-

ing approx. 5 seconds. During this phase no information can be received or sent via the

bus.

3.1. Addressing of the device at the bus

The equipment is delivered with the bus address 15.15.255. Another address can be

programmed using the ETS.

The programming button is located at the bottom outer side of the front panel of the

device and is recessed. Use a thin object to reach the button, e. g. a 1.5 mm² wire.

Key function readiness

Fig. 1

0s 0.2s 5.2s

Key Y

Key X

Design

FunctionY

Key function readiness

Area function

Examples of normal key functions

0.5 s block

Key X

Design

Area function

KeyY

Design

Function X

Key X

KeyY 0.5 s block

Design

Area function

Area function examples

readiness

6 Display and operation at the device

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

When programming mode is active, the programming LED lights up and all other LEDs

also flash.

4. Display and operation at the device

4.1. Adjust room temperature (using the example

KNX eTR 205 Light)

Depending on the setting of the "Display mode" parameter in the device application,

the KNX eTR 205/206 Light push button displays the current room temperature

value (or mixed value), the target value or the shift in relation to the basic setpoint. The

display can be dimmed and switched off via the bus so that no value is displayed.

Option A: Display of actual temperature (room temperature)

The current room temperature is displayed. It is not possible to change the room

temperature manually using the +/- buttons.

Option B: Display of target temperature or basic setpoint shift

Depending on the setting, the current target value or the shift relative to the base

setpoint is displayed. The temperature can be changed by touching the +/- buttons.

Target value display (absolute value):

PRG

Fig. 2

View from bottom

Temperature sensor

Tap +:

Increase room temperature

(target temperature is

increased)

Tap -:

Lower room temperature

(target temperature is lowered)

7 Display and operation at the device

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

Display of the basic setpoint shift (change compared to the basic setpoint of the

control):

Option C: Display of actual temperature and target temperature/basic

setpoint shift

During normal operation, the current room temperature is displayed. By touching the

buttons, the display jumps to the target temperature or to the basic setpoint shift,

depending on the presetting. Changes with + or - are visible. The display returns to the

room temperature if no button is touched for 7 seconds.

Touch the + or - button briefly: The current target temperature (or the basic setpoint

shift) is displayed.

Tap +: Increase room temperature

(target temperature/basic setpoint shift is increased).

Tap -: Lower room temperature

(target temperature/basic setpoint shift is lowered).

Tap +:

Increase room temperature

(Basic setpoint shift direction

PLUS)

Tap -:

Lower room temperature

(Basic setpoint shift direction

MINUS)

8 Display and operation at the device

KNX eTR 205/206 Light push button • Version: 12.12.2022 • Technical changes and errors excepted.

General:

The step size for the change and the possible setting range are defined in the device

application (ETS). There you can also define whether the manually changed values are

retained after a mode change (e.g. Eco mode overnight) or reset to the stored values.

The button functions can be disabled in the ETS or locked due to operating mode with

priority 1.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente

elsner elektronik 71162 Guida

Manuali Apparecchio di illuminazione popolari di altre marche